rada tf503 tIMEd floW Controls

jhplumb.com
  • No tags were found...

rada tf503 tIMEd floW Controls

timed flow controlsrada tf503 timed flow controls• Water saving• Vandal resistant• Minimal maintenance• Easy to use - push-button controls• Ideal for group showering applicationsRada TF503Dimensions (mm)32Rada TF503B88Specify as: Rada TF503 (2.1.122.01.2)Exposed ½” push-button flow control with 30 second timed flow andcomplete with 15 mm compression fittings. Incorporates internal flowadjuster.Rada TF5031069-8485Specify as: Rada TF503 b (3.0.122.45.3)Concealed ½” push-button flow control with 30 second timed flowand complete with stainless steel concealing plate and 15 mmcompression fittings. Incorporates internal flow adjuster.Flow Diagram0.070.06117 88152Pressure (bar)0.050.040.030.02Rada TF503 b361130.0104 5 6 7 8 9 10Flow Rate (l/min)with flow adjuster fully openKohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


timed flow controlsTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.ConnectionsAll models 15 mm compression.Alternatively a ¾” BSP male thread is available by removing thecompression nuts.ApprovalsWRAS approved (Water Regulations Advisory Scheme)Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.OperationThe flow cycle is activated by pressing the flow button. The flowrate is constant and is automatically turned off after a period ofapproximately 30 seconds.For economy in the use of energy and water an economical flow ratecan be obtained by adjustment of the internal flow adjuster.MaterialsBody: Copper alloy.Concealing plate of TF503 b: Stainless steel.Pressures/Flow RateMaximum static pressure: 7 bar.WeightProduct Gross Weight (Kgs) Total PackagedWeight (Kgs)Rada TF503 0.630 0.750Rada TF503 B 1.380 1.520Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P1539/18


Timed flow controlsrada autosense (SA 163U) for urinal flushing• Hygienic no-touch automatic flushing• Low Power warning LED• 12 or 24 hour ‘Duty Flush’• Accurate electronic timed flow control• Water economy and energy savings• Low visual impact• Easy to install and maintain• Unique compact designSpecify as: Rada Autosense Battery Operated Urinal FlushingControl (2.1.409.11.1)Complete with infra-red sensor, batteries and solenoid with 15 mmcompression fitting.Dimensions (mm)sensorRada Autosense InstallationBox containing Batteries, Sensorand Control Unit150 5080Existing waterflushing tankBox containingSolenoid Valve2.5 msolenoid156 59893 m x 0.4 mKohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


Timed flow controlsTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.Rada Autosense (SA 163U) is a battery powered urinal flushingoperating system designed to provide water economy and energysaving benefits within the washroom.years service (using higher power alkaline batteries).Low power warning LED.Sensor detection area: 3 metres by 0.4 metres area at 0.25 metresheight.Sensor range: 3 metres maximum.Rada Autosense can be preset to allow water to flush single or groupurinals when the sensor detects the presence of a user. Both thewaiting time prior to flushing and the flush duration can be preset.Designed to be used in the UK with a flushing cistern and installed tosatisfy the current Water Regulations.* The water supply to the solenoid valve is recommended to be fittedwith a strainer and isolation valve.FlushingFlush duration can be preset to between 1 and 189 seconds.Automatic 12 or 24 hour preset duty flush if no one uses the urinal.ApprovalsCE Approved.Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Managenment Systems.OperationThe infra-red sensor detects the presence of user.Flush cycle is activated when user leaves after a preset waiting timewhich can be adjusted to suit individual preference.MaterialsCover: Off-white plastic housing.Solenoid valve: glass-reinforced acetal body with EPDM diaphragm.Note! The unit is supplied with securing screws and fixings.Temperature RangeOperating ambient temperature range: 4°C to 55°C.Maximum humidity: 80% at 25°C.PressuresWorking pressure: 0.1 - 8 bar (0.3 - 10 bar in Europe).Electrical SpecificationProtection class: IP51.Supply voltage: powered by 4 AA LR6 MIN/500 alkaline batteries(supplied).Typical battery pack life approximately 150, 000 operations, or 2Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P2982/6


timed flow controls - electronicrada pulse electronic washroom controlThe Rada Pulse electronic washroom flow control system will enable the precise control of showering, hand washing and urinal flushing outlets.A single Rada Pulse control box will control up to 10 outlets in any configuration. Each outlet is operated via a no touch sensor, ensuringmaximum hygiene in the washroom.The system is programmed remotely, via a hand held programmer. The Rada Pulse hand held programmer is simply plugged into the controlbox then used to either set up or adjust the flow settings of each individual outlet. This is done by following the easy to use menu structure.Water flow to each outlet can be controlled to the second thereby providing the ultimate in economy. After adjusting the settings theprogrammer can be removed and thus stop any unwanted tampering.Rada Pulse Control BoxSolenoid ValveCeiling SensorShowerWashbasinWall Mounted SensorUrinalShowering and Hand WashingAfter the user has activated the sensor the flow of water to the shower or basin spout runs for a preset period, after which the water isautomatically shut off. If the user wishes to continue washing, they simply re-activate the sensor. Time setting functions can be easilyprogrammed into the Rada Pulse Control Box using the Rada Pulse Hand Held Programmer.Urinal FlushingAfter the user has activated the sensor for a single urinal there is an optional pre-flush of water to the urinal for a preset period, after which thewater is automatically shut off. Time setting functions and duty flush cycles can be easily programmed into the Rada Pulse Control Box usingthe Rada Pulse Hand Held Programmer.Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


Timed flow controls - electronicTECHNICAL SPECIFICATIONControl BoxInstallation and MaintenanceThe control box is supplied with an easy to use fixing template andcan be mounted in any plane. Access to the programmer socketshould be considered when installing the control boxMaterialsControl box: PC/ABS blended plastic to give the product fire-retardantqualities.Electrical SpecificationProtection class: Control box IP54.Supply voltage: 230 V AC, 50/60 HZ.Transformer: 230 V AC/12 V AC.Maximum humidity: 80% at 35°C.Hand Held ProgrammerInstallation and MaintenanceThe hand held controller has a back lit two line alpha numeric display.A four button key pad is used for scrolling through the menu structureand programming the timing options.The programmer is multilingual and can be set by the user to displaythe menu in one of nine languages.MaterialsProgrammer: Tough ABS plastics. The hand held programmer has a3 m extendable coiled cable with a pin plug attachment for connectionto the control box.120/122 ‘No-touch’ SensorInstallation and MaintenanceThe sensor should be mounted on a flat smooth surface (e.g. centreof a tile) so that the seal on the reverse can prevent water ingress,otherwise a silicone sealant should be used. The sensor back plateis mounted via two fixing points. The cover is then fitted over theback plate and secured with a security screw on the underside of thecover. This conceals the wall fixing screws and prevents unwantedtampering.MaterialsWall Mounted Sensor: Chromium plated durable engineering plasticwith shatterproof plastic sensing window.Electrical SpecificationProtection class: Sensor, electronic module IP65.Supply voltage: 12V AC + 10% 50/60 HZ, via Rada Pulse ControlBox.


timed flow controls - electronicTECHNICAL SPECIFICATION129 ‘No-touch’ SensorInstallation and MaintenanceThe sensor should be mounted on a flat smooth surface (e.g. centreof a tile) so that the seal on the reverse can prevent water ingress,otherwise a silicone sealant should be used. The sensor is mountedvia two fixing points.MaterialsWall Mounted Sensor: Chromium plated brass with shatterproofplastic sensing window.Electrical SpecificationProtection class: Sensor, electronic module IP65.Supply voltage: 12V AC + 10% 50/60 HZ, via Rada Pulse ControlBox.124/125 and 126 Ceiling Mounted Concealed SensorInstallation and MaintenanceThe sensor is recessed into false ceilings or ceiling tiles, and issupplied with a conduit box, front fixings, plate and cover screws.Note! The ceiling sensor is not recommended for use in a highhumidity environment such as a shower changing room.MaterialsCeiling Sensor: Base - ABS, cover - polycarbonate.Electrical SpecificationProtection class: Sensor, electronic module IP55.Supply voltage: 12V AC + 10% 50/60 HZ, via Rada Pulse ControlBox.SV1015 Solenoid ValveInstallation and MaintenanceThe solenoid valve should be accessible for maintenance purposes.Supplied complete with integral isolator and filter.MaterialsSolenoid Valve: Body material fibreglass polymide.PressuresSolenoid valve: 0.2 - 10 bar (20 - 1000 kPa).Electrical SpecificationProtection Class: Solenoid Coil IP65Coil 12 V AC, 5.5 VA, 50/60 Hz.Typical cable requirements (cross-sectional area and length): 0.5 sqmm up to 27 m, 0.75 sq mm up to 40 m, 1.00 sq mm up to 53 m.Note: Alternative solenoid valves are available for applications outsidethis specification. Contact Specification Enquiries for details.


timed flow controls - electronicTECHNICAL SPECIFICATIONControl Box129 ‘No-touch’ Sensor300 11712 6884 6230Hand Held Programmer124/125 and 126 Ceiling Mounted Concealed Sensor95 3016559.5 to 251201578dia128 dia120/122 ‘No-touch’ SensorSV1015 Solenoid Valve68 2284686127Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P3422/5


timed flow controls - electronicrada mono-control mc122 for urinal flushing• Hygiene ‘no-touch’ automatic urinal flushing• Wall mounted sensor for ‘no-touch’ control of a singleurinal• Programmable flush times provides flexibility andgreater economy• Automatic duty flush when building unoccupied• All elements linked via safe extra low voltage (12Volts) supplyDimensions (mm)68 22684Specify as: Mono-Control System MC122 (1.1495.009)Each urinal bowl to be served by one Rada Mono-Control SystemMC122 wall mounted flushing control. Complete with concealedpassive infra-red sensor, control module and ½” solenoid valve withisolator and filter.68127533564Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


timed flow controls - electronicTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.PressuresSolenoid valve: 0.2 - 10 bar (20 - 1000 kPa).When the design of today’s washrooms require higher levels ofhygiene and energy savings, Rada provide the solution.Rada Mono-Control systems enable precise control of showering,hand washing and urinal flushing systems.The sensor should be mounted on a flat smooth surface (e.g. centreof a tile) so that the seal on the reverse can prevent water ingress,otherwise a silicone sealant should be used. The sensor back plateis mounted via two fixing points. The cover is then fitted over theback plate and secured with a security screw on the underside of thecover. This conceals the wall fixing screws and prevents unwantedtampering.The solenoid valve should be accessible for maintenance purposes.Supplied complete with integral isolator and filter.Electrical SpecificationProtection class: Sensor, electronic module IP65.Supply voltage: 12V AC + 10% 50/60 HZ, via Rada 302, 308 or 316transformer (not included).Power consumption: 6 VA.Operating ambient temperature range: 5°C - 40°C.Maximum humidity: 80%.Wiring from sensor to control module: 2 core PVC covered cable,3.0 m supplied.Sensor range: 0 - 550 mm.Operation SchematicApprovalsWRAS approved (Water Regulations Advisory Scheme).CE Approved.Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.Rada TransformerOperationWhen the sensor is activated, if the pre-flush option has beenselected, there will be an approximate 2 second delay and 2 secondpre-flush.Control Module andSolenoid ValveWhen there has been 5 seconds of inactivity (when the user hasleft the area), the flush is activated for the duration selected (3 - 10seconds, in 1 second intervals).MaterialsWall Mounted Sensor: Chromium plated durable engineering plasticwith shatterproof plastic sensing window.Solenoid Valve: Body material fibreglass polymide.Flush TimingThe system provides an optional pre-flush of 2 seconds if a humanbody is detected and then initiates a flush cycle after usage.Flush duration can be pre-set, between 3 - 10 seconds in incrementsof 1 second, by the adjustment of the integral timing dial.A duty flush is incorporated, every 24 hours after usage.The Control Module attaches directly onto the solenoid valve.Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P3776/3


timed flow controls - electronicrada mono-control mc120 for showering and handwashing• Hygiene ‘no-touch’ control• Wall mounted sensor for ‘no-touch’ control of a singlewash basin or shower• Economy and flexibility - timing can be programmedto suit application• All elements linked via safe extra low voltage (12Volts) supplyDimensions (mm)68 22684Specify as: Mono-Control System MC120 (1.1495.009)Each outlet to be served by one Rada Mono-Control System MC120wall mounted flow control. Complete with chrome plated concealedactive infra-red sensor, control module and ½” solenoid valve withisolator and filter.68127533564Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


timed flow controls - electronicTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.When the design of today’s washrooms require higher levels ofhygiene and energy savings, Rada provide the solution.Rada Mono-Control systems enable precise control of showering,hand washing and urinal flushing systems.Cycle TimingFlow duration can be pre-selected during commissioning by theadjustment of an integral timing dial.a) Cycle time in seconds, full cycle only3, 4, 5, 6, 7, 8, 9, 15, 30, 60b) Cycle time in seconds, cycle can be stopped by reactivating sensor5, 10, 15, 30, 60, 75The sensor should be mounted on a flat smooth surface (e.g. centreof a tile) so that the seal on the reverse can prevent water ingress,otherwise a silicone sealant should be used. The sensor back plateis mounted via two fixing points. The cover is then fitted over theback plate and secured with a security screw on the underside of thecover. This conceals the wall fixing screws and prevents unwantedtampering.The solenoid valve should be accessible for maintenance purposes.Supplied complete with integral isolator and filter.ApprovalsWRAS approved (Water Regulations Advisory Scheme).CE Approved.Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.PressuresSolenoid valve: 0.2 - 10 bar (20 - 1000 kPa).Electrical SpecificationProtection class: Sensor, electronic module IP65.Supply voltage: 12V AC + 10% 50/60 HZ, via Rada 302, 308 or 316transformer (not included).Power consumption: 6 VA.Operating ambient temperature range: 5°C - 40°C.Maximum humidity: 80%.Wiring from sensor to control module: 2 core PVC covered cable,3.0 m supplied.Operation SchematicOperationWhen the sensor is activated, a signal is sent to the Rada Mono-Control module, which, in turn, energises the solenoid valve.The solenoid valve opens - allowing water to flow through the outlet.Control Module andSolenoid ValveThe duration of the flow for each outlet can be individually preset, viathe Rada Mono-Control module, ensuring optimum saving of waterand energy.The sensor may be used to switch off the supply of water before thepreset time.MaterialsWall Mounted Sensor: Chromium plated durable engineering plasticwith shatterproof plastic sensing window.Solenoid Valve: Body material fibreglass polymide.Rada TransformerKohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P3787/4


timed flow controls - electronicrada pulse 122 operating system for individual urinal flushing• Hygiene ‘no-touch’ automatic urinal flushing• Wall mounted sensor for ‘no-touch’ control of a singleurinal• Programmable flush times provides flexibility andgreater economy• Automatic duty flush when building unoccupied• All elements linked via safe extra low voltage (12Volts) supply• For use with Rada Pulse Control Box systemDimensions (mm)68 22Specify as: Rada Pulse 122 Operating System (1.1495.004)Each urinal bowl to be served by one Rada Pulse 122 OperatingSystem wall mounted flushing control. Complete with concealedactive infra-red sensor and ½” solenoid valve with isolator and filter.84668127Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


timed flow controls - electronicTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.PressuresSolenoid valve: 0.2 - 10 bar (20 - 1000 kPa).When the design of today’s washrooms require higher levels ofhygiene and energy savings, Rada provide the solution.The sensor should be mounted on a flat smooth surface (e.g. centreof a tile) so that the seal on the reverse can prevent water ingress,otherwise a silicone sealant should be used. The sensor back plateis mounted via two fixing points. The cover is then fitted over theback plate and secured with a security screw on the underside of thecover. This conceals the wall fixing screws and prevents unwantedtampering.Electrical SpecificationProtection class: Sensor, electronic module IP65.Supply voltage: 12V AC + 10% 50/60 HZ, via Rada Pulse ControlBox.Operating ambient temperature range: 0°C - 40°C.Maximum humidity: 80%.Wiring from sensor to control box: 2 core PVC covered cable,3.0 m supplied.Sensor range: 0 - 550 mm.The solenoid valve should be accessible for maintenance purposes.Supplied complete with integral isolator and filter.Operation SchematicFor details of the Rada Pulse Control Box, refer to the applicabledatasheet. Each Rada Pulse Control Box will accommodate amaximum of 10 operating systems.Rada PulseControl BoxApprovalsCE Approved.WRAS approved (Water Regulations Advisory Scheme)Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.OperationWhen the sensor is activated the Rada Pulse Control Box mayprovide a pre-flush (if required). The Rada Pulse Control Box thenwaits for a period of inactivity before operating the solenoid valve.Solenoid ValveThe solenoid valve opens - allowing water to flow through the outlet.The duration of the flow for each outlet can be individually preset, viathe Rada Pulse Control Box, ensuring optimum saving of water andenergy.MaterialsWall Mounted Sensor: Chromium plated durable engineering plasticwith shatterproof plastic sensing window.Solenoid Valve: Body material fibreglass polymide.Pre-flush, Delay and Flush TimingThe operating systems are programmed remotely, via the Hand HeldProgrammer. The programmer is simply plugged into the control boxthen used to either set up or adjust the flow timings using the easy tofollow menu structure.The programmer can be removed after adjustment to preventunwanted tampering.Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P3789/3


timed flow controls - electronicrada pulse control box and hand held programmerControl Box• Provides central control for complete washroomsystem• Controls up to 10 individual showers, hand washbasins or urinals• Integral 12 volt transformer• Provides interface for auxiliary equipment e.g. pumps,ventilation fans or light systems• Robust construction• Compatible with all Rada Pulse Operating systems,sensors and solenoidsHand Held Programmer• Allows the user to program mode of operation, dutycycles and flow duration for individual outlets• Flexible programming to ensure maximum economy• Easy to follow menu• Multi-lingual• Easy to use ‘copy and paste’ facility to assistprogramming multiple outlets• Back lit alpha numeric display• Fault finding facilitySpecify as: Rada Pulse Control Box (2.1.093.79.1)‘A complete washroom system control unit’ with 12 V transformercapable of controlling up to 10 Rada Pulse Operating Systems.Specify as: Rada Pulse Hand Held Programmer (2.1.093.80.1)With four touch sensitive buttons, two line back lit alpha numericdispaly and 3.0 metres extendable coiled cable suitable forprogramming the Rada Pulse Control Box.Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


timed flow controls - electronicTECHNICAL SPECIFICATIONDescriptionThe Rada Pulse electronic washroom flow control system will enablethe precise control of showering, hand washing and urinal flushingoutlets. A single Rada Pulse control box will control up to 10 outlets inany configuration. Each outlet is operated via a no touch sensor anda universal solenoid valve (refer to Operating System datasheets formore information), ensuring maximum hygiene in the washroom.Electrical SpecificationProtection class: Control box IP54.Supply voltage: 230 V AC, 50/60 HZ.Transformer: 230 V AC/12 V AC.Maximum humidity: 80% at 35°C.The system is programmed remotely, via a hand held programmer.The Rada Pulse hand held programmer is simply plugged into thecontrol box then used to either set up or adjust the flow settings ofeach individual outlet or check for faults in cable runs to solenoids andsensors. This is done by following the easy to use menu structure.Installation and MaintenancePlease refer to the appropriate Product Manual.Dimensions (mm)300 117The control box is supplied with an easy to use fixing template andcan be mounted in any plane. Access to the programmer socketshould be considered when installing the control box.Note! Any combination of showering, washbasin or urinal flushing(up to a maximum of 10) can be controlled from a single Rada Pulsecontrol box. In addition the control box will also provide a signal for upto 3 auxiliary functions e.g. fans, lights and pumps.230The hand held controller has a back lit two line alpha numeric display.A four button key pad is used for scrolling through the menu structureand programming the timing options.95 30The programmer is multilingual and can be set by the user to displaythe menu in one of nine languages.ApprovalsComplies with all relevant directives for CE marking.Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.120MaterialsControl box: PC/ABS blended plastic to give the product fire-retardantqualities.Programmer: Tough ABS plastics. The hand held programmer has a3 m extendable coiled cable with a pin plug attachment for connectionto the control box.Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P3790/3


timed flow controls - electronicrada pulse 120 operating system for showering and hANDWASHING• Hygiene ‘no-touch’ control• Suitable for showering and handwashing• Wall mounted sensor for ‘no-touch’ control of a singlewashbasin or shower• Economy and flexibility - timing can be programmedto suit application• All elements linked via safe extra low voltage (12Volts) supply• For use with Rada Pulse Control Box systemDimensions (mm)Specify as: Rada Pulse 120 Operating System (1.1495.003)Each outlet to be served by one Rada Pulse 120 Operating Systemwall mounted ‘no touch’ flow control. Complete with concealed activeinfra-red sensor and ½” solenoid valve with isolator and filter.68 2284668127Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


timed flow controls - electronicTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.When the design of today’s washrooms require higher levels ofhygiene and energy savings, Rada provide the solution.The sensor should be mounted on a flat smooth surface (e.g. centreof a tile) so that the seal on the reverse can prevent water ingress,otherwise a silicone sealant should be used. The sensor back plateis mounted via two fixing points. The cover is then fitted over theback plate and secured with a security screw on the underside of thecover. This conceals the wall fixing screws and prevents unwantedtampering.The solenoid valve should be accessible for maintenance purposes.Supplied complete with integral isolator and filter.For details of the Rada Pulse Control Box, refer to the applicabledatasheet. Each Rada Pulse Control Box will accommodate amaximum of 10 operating systems.Cycle TimingThe operating systems are programmed remotely , via the Hand HeldProgrammer. The programmer is simply plugged into the control boxthen used to either set up or adjust the flow timings using the easy tofollow menu structure.The programmer can be removed after adjustment to preventunwanted tampering.PressuresSolenoid valve: 0.20 - 10 bar (20 - 1000 kPa).Electrical SpecificationProtection class: Sensor, electronic module IP65.Supply voltage: 12V AC + 10% 50/60 HZ, via Rada Pulse ControlBox.Operating ambient temperature range: 0°C - 40°C.Maximum humidity: 80%.Wiring from sensor to control box: 2 core PVC covered cable,3.0 m supplied.Sensor range: 0 to 50 mm.ApprovalsCE Approved.WRAS approved (Water Regulations Advisory Scheme)Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.Operation SchematicRada PulseControl BoxOperationWhen the sensor is activated, a signal is sent to the Rada PulseControl Box, which, in turn, energises the solenoid valve.The solenoid valve opens - allowing water to flow through the outlet.The duration of the flow for each outlet can be individually preset, viathe Rada Pulse Control Box, ensuring optimum saving of water andenergy.The sensor may be used to switch off the supply of water before thepre-set time.MaterialsWall Mounted Sensor: Chromium plated durable engineering plasticwith shatterproof plastic sensing window.Solenoid Valve: Body material fibreglass polymide.Solenoid ValveKohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P3791/3


timed flow controlsTimed Flow Controls - applicationsIndividual Timed Flow Control for Group Showers - MechanicalRada VR145Rada TF503Rada 320 cIndividually activated, ‘non-concussive’,mechanical valves, with approximately30 seconds timed flow duration. Thetemperature is pre-set via a ‘groupcontrol’thermostatic mixing valve.Note: ‘Group-control’ applications aredependent on the maintained waterpressure available. Please refer toSpecification Enquiries,Tel:01242 282527 for advice.Individual Timed Flow Control for Group Showers - ElectronicRada 320 cRada Solenoid ValveRada VR125Rada 120 SensorNo-touch sensor and solenoid valveoperation with programmable timedflow control (see Rada Pulse). Thetemperature is pre-set via a ‘groupcontrol’ thermostatic mixing valve.Note: ‘Group-control’ applications aredependent on the maintained waterpressure available. Please refer toSpecification Enquiries,Tel: 01242 282527 for advice.Individual Showering with Timed Flow Control - Mechanical - TMV3 ApprovedRada VR105Rada TF503bRada VR145‘Built-in’ and ‘exposed’ thermostaticmixing valves allowing individualtemperature selection with separate,non-concussive, mechanical timed flowvalves of approximately 30 secondsduration.Rada 215-t3bcRada TF503Rada 215-t3 cKohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


timed flow controlsTimed Flow Controls - applicationsUnder Basin Mixing Valve for Multiple ApplicationMeynell Push Action Pillar TapPre-set thermostatically controlled hotwater via under-basin mixing valvefor multiple wash basin application.Flow activated by ‘non-concussive’,mechanical valves with approximately15 seconds timed flow duration.Rada 222-t3 dkSingle & Group UrinalsRada PulseControl BoxTimed flow control activated by eitherno-touch wall mounted or ceilingmounted sensor (see Rada Pulse).Rada solenoid ValveType ‘dC’Pipe interrupterRada PulseHand HeldProgrammersolenoidValve150mmRada 122 sensor≥300mmKohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P3887/2


timed flow controlsrada tf31 timed flow controls• Water saving• Vandal resistant• Minimal maintenance• Easy to use - push-button controls• Specially designed for prison applicationsSpecify as: Rada TF31/1 (1.0.095.01.1), Rada TF31/2(1.0.095.02.1), Rada TF31/3 (1.0.095.03.1)½” push-button flow control for duct mounting with 30 second timedflow and complete with extended rod options for extra security andvarying wall thickness with 15 mm compression fittings. Incorporatesinternal flow adjuster.Dimensions (mm)Flow DiagramAB 490.0786Ø500.060.05(bar)0.04Model‘A’Overall Length‘B’wall thicknessPressure0.030.020.01TF31/1 340 100 - 140Tf31/2 380 142 - 18204 5 6 7 8 9 10Flow Rate (l/min)with flow adjuster fully openTf31/3 445 206 - 246Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


timed flow controlsTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.ConnectionsAll models 15 mm compression.Alternatively a ¾” BSP male thread is available by removing thecompression nuts.ApprovalsWRAS approved (Water Regulations Advisory Scheme)Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.OperationThe flow cycle is activated by pressing the flow button. The flowrate is constant and is automatically turned off after a period ofapproximately 30 seconds.For economy in the use of energy and water an economical flow ratecan be obtained by adjustment of the internal flow adjuster.MaterialsBody: Copper alloy.Pressures/Flow RateMaximum static pressure: 7 bar.Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5334


timed flow controls - electronicrada mono-control mc125 for urinal flushing• Hygiene ‘no-touch’ automatic urinal flushing• Ceiling mounted for ‘no-touch’ control of a singleurinal• Programmable flush times provides flexibility andgreater economy• Automatic duty flush when building unoccupied• All elements linked via safe extra low voltage (12Volts) supplyDimensions (mm)55169.5 to 25Specify as: Mono-Control System MC125 (1.1495.012)Each urinal bowl to be served by one Rada Mono-Control SystemMC125 ceiling mounted flow control. Complete with concealedpassive infra-red sensor, control module and ½” solenoid valve withisolator and filter.1578dia128 dia68127533564Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


timed flow controls - electronicTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.When the design of today’s washrooms require higher levels ofhygiene and energy savings, Rada provide the solution.Rada Mono-Control systems enable precise control of showering,hand washing and urinal flushing systems.The ceiling sensor is recessed into false ceilings or ceiling tiles and issupplied with a conduit box, front fixings, plate and cover screws.Electrical SpecificationProtection class: Sensor, electronic module IP55.Supply voltage: 12V AC + 10% 50/60 HZ, via Rada 302, 308 or 316transformer (not included).Power consumption: 6 VA.Operating ambient temperature range: 5°C - 40°C.Maximum humidity: 80%.Wiring form sensor to control module: 2 core PVC covered cable, 3.0m supplied.Sensor range: minimum 0.5 metres, maximum 2.5 metres.The solenoid valve should be accessible for maintenance purposes.Supplied complete with integral isolator and filter.Operation SchematicApprovalsWRAS approved (Water Regulations Advisory Scheme).CE Approved.Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.OperationWhen the sensor is activated, if the pre-flush option has beenselected, there will be an approximate 2 second delay and a 2 secondpre-flush.Rada TransformerWhen there has been 5 seconds of inactivity (when the user hasleft the area), the flush is activated for the duration selected (3 - 10seconds, in 1 second intervals).Control Module andSolenoid ValveMaterialsCeiling Sensor: Base - ABS, cover - polycarbonate.Solenoid Valve: Body material fibreglass polymide.Flush TimingThe system provides an optional pre-flush of 2 seconds if a humanbody is detected and then initiates a flush cycle after usage.Flush duration can be pre-set, between 3 - 10 seconds in incrementsof 1 second, by the adjustment of the integral timing dial.A duty flush is incorporated, every 24 hours after usage.The Control Module attaches directly onto the solenoid valve.PressuresSolenoid valve: 0.2 - 10 bar (20 - 1000 kPa).Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5493


timed flow controls - electronicrada mono-control mc126 for Group urinal flushing• Hygiene ‘no-touch’ automatic urinal flushing• Ceiling mounted for ‘no-touch’ control of a singleurinal• Programmable flush times provides flexibility andgreater economy• Automatic duty flush when building unoccupied• All elements linked via safe extra low voltage (12Volts) supplyDimensions (mm)55169.5 to 25Specify as: Mono-Control System MC126 (1.1495.013)Each group of urinal bowls to be served by one Rada Mono-Control System MC126 ceiling mounted flow control. Complete withconcealed passive infra-red sensor, control module and ½” solenoidvalve with isolator and filter.1578dia128 dia68127533564Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


timed flow controls - electronicTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.When the design of today’s washrooms require higher levels ofhygiene and energy savings, Rada provide the solution.Rada Mono-Control systems enable precise control of showering,hand washing and urinal flushing systems.The ceiling sensor is recessed into false ceilings or ceiling tiles and issupplied with a conduit box, front fixings, plate and cover screws.Electrical SpecificationProtection class: Sensor, electronic module IP55.Supply voltage: 12V AC + 10% 50/60 HZ, via Rada 302, 308 or 316transformer (not included).Power consumption: 6 VA.Operating ambient temperature range: 5°C - 40°C.Maximum humidity: 80%.Wiring form sensor to control module: 2 core PVC covered cable, 3.0m supplied.Sensor range: minimum 0.5 metres, maximum 2.5 metres.The solenoid valve should be accessible for maintenance purposes.Supplied complete with integral isolator and filter.Operation SchematicApprovalsWRAS approved (Water Regulations Advisory Scheme).CE Approved.Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.Control Module andSolenoid ValveRada TransformerOperationWhen the sensor is activated, a signal is sent to the Rada Mono-Control module which initiates a delay, after which the solenoid valveopens - allowing water to flow through the outlet.The duration of the flow and the delay can be pre-set, via the RadaMono-Control module, ensuring optimum saving of water and energy.MaterialsCeiling Sensor: Base - ABS, cover - polycarbonate.Solenoid Valve: Body material fibreglass polymide.Flush TimingThe system provides a flush duration which can be set for 6, 9, 11 or13 seconds.This will operate after a flush delay of either 30 seconds, 1 minute, 2minutes or 3 minutes. These settings can be adjusted via the integraltiming dial.A duty flush is incorporated, every 24 hours after usage.The Control Module attaches directly onto the solenoid valve.PressuresSolenoid valve: 0.2 - 10 bar (20 - 1000 kPa).Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5494


timed flow controls - electronicrada mono-control mc124 for handwashing• Hygiene ‘no-touch’ control• Ceiling mounted sensor for ‘no-touch’ control ofindividual washbasins• Economy and flexibility - timing can be programmedto suit application• All elements linked via safe extra low voltage (12Volts) supplyDimensions (mm)55151678dia9.5 to 25Specify as: Mono-Control System MC124 (1.1495.011)Each washbasin to be served by one Rada Mono-Control SystemMC124 ceiling mounted flow control. Complete with concealedpassive infra-red sensor, control module and ½” solenoid valve withisolator and filter.128 dia68127533564Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


timed flow controls - electronicTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual .When the design of today’s washrooms require higher levels ofhygiene and energy savings, Rada provide the solution.Rada Mono-Control systems enable precise control of showering,hand washing and urinal flushing systems.The ceiling sensor is recessed into false ceilings or ceiling tiles and issupplied with a conduit box, front fixings, plate and cover screws.Electrical SpecificationProtection class for control module: IP55.Protection class for sensor: IP00.Supply voltage: 12V AC + 10% 50/60 HZ, via Rada 302, 308 or 316transformer (not included).Power consumption: 6 VA.Operating ambient temperature range: 5°C - 40°C.Maximum humidity: 80%.Wiring from sensor to control module: 2 core PVC covered cable,3.0 m supplied.Sensor range: minimum 0.5 m, maximum 2.5 m.The solenoid valve should be accessible for maintenance purposes.Supplied complete with integral isolator and filter.Operation SchematicApprovalsWRAS approved (Water Regulations Advisory Scheme).CE Approved.Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.OperationWhen the sensor is activated, a signal is sent to the Rada Mono-Control module, which, in turn, energises the solenoid valve.2.5 m Max.The solenoid valve opens - allowing water to flow through the outlet.The duration of the flow for each outlet can be individually preset, viathe Rada Mono-Control module, ensuring optimum saving of waterand energy.Control Module andSolenoid ValveRada TransformerMaterialsCeiling Sensor: Base - ABS, cover - polycarbonate.Solenoid Valve: Body material fibreglass polymide.Cycle TimingFlow duration can be pre-selected during commissioning by theadjustment of an integral timing dial in steps from 1 second upto 16seconds.The Control Module attaches directly onto the solenoid valve.PressuresSolenoid valve: 0.2 - 10 bar (20 - 1000 kPa).Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5495


timed flow controls - electronicrada mono-control mc129 for showering and handwashing• Hygiene ‘no-touch’ control• Wall mounted sensor for ‘no-touch’ control of a singlewash basin or shower• Economy and flexibility - timing can be programmedto suit application• All elements linked via safe extra low voltage (12Volts) supplyDimensions (mm)12 6884 6Specify as: Mono-Control System MC129 (1.1495.014)Each outlet to be served by one Rada Mono-Control System MC129wall mounted flow control. Complete with chrome plated active infraredsensor, control module and ½” solenoid valve with isolator andfilter.68127533564Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


timed flow controls - electronicTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.PressuresSolenoid valve: 0.2 - 10 bar (20 - 1000 kPa).When the design of today’s washrooms require higher levels ofhygiene and energy savings, Rada provide the solution.Rada Mono-Control systems enable precise control of showering,hand washing and urinal flushing systems.The sensor should be mounted on a flat smooth surface (e.g. centreof a tile) so that the seal on the reverse can prevent water ingress,otherwise a silicone sealant should be used. The sensor is mountedvia two fixing points.The solenoid valve should be accessible for maintenance purposes.Supplied complete with integral isolator and filter.Electrical SpecificationProtection class: Sensor, electronic module IP65.Supply voltage: 12V AC + 10% 50/60 HZ, via Rada 302, 308 or 316transformer (not included).Power consumption: 6 VA.Operating ambient temperature range: 5°C - 40°C.Maximum humidity: 80%.Wiring from sensor to control module: 2 core PVC covered cable,3.0 m supplied.Operation SchematicApprovalsWRAS approved (Water Regulations Advisory Scheme).CE Approved.Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.Rada TransformerOperationWhen the sensor is activated, a signal is sent to the Rada Mono-Control module, which, in turn, energises the solenoid valve.The solenoid valve opens - allowing water to flow through the outlet.Control Module andSolenoid ValveThe duration of the flow for each outlet can be individually preset, viathe Rada Mono-Control module, ensuring optimum saving of waterand energy.The sensor may be used to switch off the supply of water before thepreset time.MaterialsSensor: Chromium plated metal with shatterproof plastic sensingwindow.Solenoid Valve: Body material fibreglass polymide.Cycle TimingFlow duration can be pre-selected during commissioning by theadjustment of an integral timing dial.a) Cycle time in seconds, full cycle only3, 4, 5, 6, 7, 8, 9, 15, 30, 60.b) Cycle time in seconds, cycle can be stopped by reactivating sensor5, 10, 15, 30, 60, 75.Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5496


timed flow controls - electronicrada pulse 124 operating system for Handwashing• Hygiene ‘no-touch’ control• Ceiling mounted sensor for ‘no-touch’ control ofindividual washbasins• Econony and flexibility - timing can be programmed tosuit application• All elements linked via safe extra low voltage (12Volts) supply• For use with Rada Pulse Control Box systemDimensions (mm)Specify as: Rada Pulse 124 Operating System (1.1495.005)Each outlet to be served by one Rada Pulse 124 Operating Systemceiling mounted flow control. Complete with concealed passive infraredsensor and ½” solenoid valve with isolator and filter.16559.5 to 251578dia128 dia68127Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


timed flow controls - electronicTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.When the design of today’s washrooms require higher levels ofhygiene and energy savings, Rada provide the solution.The sensor is recessed into false ceilings or ceiling tiles, and issupplied with a conduit box, front fixings, plate and cover screws.Note! The ceiling sensor is not recommended for use in a highhumidity environment such as a shower changing room.Electrical SpecificationProtection class: Sensor, electronic module IP55.Supply voltage: 12V AC + 10% 50/60 HZ, via Rada Pulse ControlBox.Operating ambient temperature range: 0°C - 40°C.Maximum humidity: 80%.Wiring from sensor to control box: 2 core PVC covered cable,3.0 m supplied.Sensor range: between 0.50 and 2.5 metres.The solenoid valve should be accessible for maintenance purposes.Supplied complete with integral isolator and filter.Operation SchematicFor details of the Rada Pulse Control Box, refer to the applicabledatasheet. Each Rada Pulse Control Box will accommodate amaximum of 10 operating systems.ApprovalsCE Approved.WRAS approved (Water Regulations Advisory Scheme)Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.Rada PulseControl BoxOperationWhen the sensor is activated, a signal is sent to the Rada PulseControl Box, which, in turn energises the solenoid valve.2.5 m Max.The solenoid valve opens - allowing water to flow through the outlet.The duration of the flow for each outlet can be individually pre-set, viathe Rada Pulse Control Box, ensuring optimum saving of water andenergy.MaterialsCeiling Sensor: ABS, cover - polycarbonate.Solenoid Valve: Body material fibreglass polymide.Solenoid ValveCycle TimingThe operating systems are programmed remotely , via the Hand HeldProgrammer. The programmer is simply plugged into the control boxthen used to either set up or adjust the flow timings using the easy tofollow menu structure.The programmer can be removed after adjustment to preventunwanted tampering.PressuresSolenoid valve: 0.2 - 10 bar (20 - 1000 kPa).Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5497


timed flow controls - electronicrada pulse 129 operating system for showering and hANDWASHING• Hygiene ‘no-touch’ control• Suitable for showering and handwashing• Wall mounted sensor for ‘no-touch’ control of a singlewashbasin or shower• Economy and flexibility - timing can be programmedto suit application• All elements linked via safe extra low voltage (12Volts) supply• For use with Rada Pulse Control Box systemDimensions (mm)Specify as: Rada Pulse 129 Operating System (1.1495.008)Each outlet to be served by one Rada Pulse 129 Operating Systemwall mounted ‘no touch’ flow control. Complete with chrome platedactive infra-red sensor and ½” solenoid valve with isolator and filter.12 6884 668127Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


timed flow controls - electronicTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.PressuresSolenoid valve: 0.2 - 10 bar (20 - 1000 kPa).When the design of today’s washrooms require higher levels ofhygiene and energy savings, Rada provide the solution.The sensor should be mounted on a flat smooth surface (e.g. centreof a tile) so that the seal on the reverse can prevent water ingress,otherwise a silicone sealant should be used. The sensor is mountedvia two fixing points.The solenoid valve should be accessible for maintenance purposes.Supplied complete with integral isolator and filter.Electrical SpecificationProtection class: Sensor, electronic module IP65.Supply voltage: 12V AC + 10% 50/60 HZ, via Rada Pulse ControlBox.Operating ambient temperature range: 0°C - 40°C.Maximum humidity: 80%.Wiring from sensor to control box: 2 core PVC covered cable,3.0 m supplied.Sensor range: 0-50mmFor details of the Rada Pulse Control Box, refer to the applicabledatasheet. Each Rada Pulse Control Box will accommodate amaximum of 10 operating systems.Operation SchematicApprovalsCE Approved.WRAS approved (Water Regulations Advisory Scheme)Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.Rada PulseControl BoxOperationWhen the sensor is activated, a signal is sent to the Rada PulseControl Box, which, in turn, energises the solenoid valve.The solenoid valve opens - allowing water to flow through the outlet.The duration of the flow for each outlet can be individually preset, viathe Rada Pulse Control Box, ensuring optimum saving of water andenergy.The sensor may be used to switch off the supply of water before thepre-set time.Solenoid ValveMaterialsWall Mounted Sensor: Chromium plated metal body with shatterproofplastic sensing window.Solenoid Valve: Body material fibreglass polymide.Cycle TimingThe operating systems are programmed remotely , via the Hand HeldProgrammer. The programmer is simply plugged into the control boxthen used to either set up or adjust the flow timings using the easy tofollow menu structure.The programmer can be removed after adjustment to preventunwanted tampering.Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5498


timed flow controls - electronicrada pulse 125 operating system for individual urinal flushingßHygiene ‘no-touch’ automatic urinal flushingß Ceiling mounted sensor for ‘no-touch’ control of asingle urinalß Programmable flush times provides flexibility andgreater economyß Automatic duty flush when building unoccupiedß All elements linked via safe extra low voltage (12Volts) supplyß For use with Rada Pulse Control Box systemDimensions (mm)Specify as: Rada Pulse 125 Operating System (1.1495.006)Each urinal bowl to be served by one Rada Pulse 125 OperatingSystem ceiling mounted flow control. Complete with concealedpassive infra-red sensor and ½” solenoid valve with isolator and filter.16559.5 to 251578dia128 dia68127Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


timed flow controls - electronicTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.When the design of today’s washrooms require higher levels ofhygiene and energy savings, Rada provide the solution.The sensor is recessed into false ceilings or ceiling tiles, and issupplied with a conduit box, front fixings, plate and cover screws.The solenoid valve should be accessible for maintenance purposes.Supplied complete with integral isolator and filter.Electrical SpecificationProtection class: Sensor, electronic module IP55.Supply voltage: 12V AC + 10% 50/60 HZ, via Rada Pulse ControlBox.Operating ambient temperature range: 0°C - 40°C.Maximum humidity: 80%.Wiring from sensor to control box: 2 core PVC covered cable,3.0 m supplied.Sensor range: between 0.50 and 2.5 metres.For details of the Rada Pulse Control Box, refer to the applicabledatasheet. Each Rada Pulse Control Box will accommodate amaximum of 10 operating systems.Operation SchematicApprovalsCE Approved.WRAS approved (Water Regulations Advisory Scheme)Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.Rada PulseControl BoxOperationWhen the sensor is activated the Rada Pulse Control Box mayprovide a pre-flush (if required). The Rada Pulse Control Box thenwaits for a period of inactivity before operating the solenoid valve.The solenoid valve opens - allowing water to flow through the outlet.The duration of the flow for each outlet can be individually preset, viathe Rada Pulse Control Box, ensuring optimum saving of water andenergy.MaterialsBase: ABS, Cover: Polycarbonate.Solenoid Valve: Body material fibreglass polymide.Solenoid ValveFlush TimingThe operating systems are programmed remotely , via the Hand HeldProgrammer. The programmer is simply plugged into the control boxthen used to either set up or adjust the flow timings using the easy tofollow menu structure.The programmer can be removed after adjustment to preventunwanted tampering.PressuresSolenoid valve: 0.2 - 10 bar (20 - 1000 kPa).Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5499


timed flow controls - electronicrada pulse 126 operating system for group urinal flushing• Hygiene ‘no-touch’ automatic urinal flushing• Ceiling mounted sensor for ‘no-touch’ control ofmultiple urinals• Programmable flush times provides flexibility andgreater economy• Automatic duty flush when building unoccupied• All elements linked via safe extra low voltage (12Volts) supply• For use with Rada Pulse Control Box systemDimensions (mm)16Specify as: Rada Pulse 126 Operating System (1.1495.007)Each group of urinal bowls to be served by one Rada Pulse 126Operating System ceiling mounted flow control. Complete withconcealed passive infra-red sensor and ½” solenoid valve withisolator and filter.559.5 to 251578dia128 dia68127Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


timed flow controls - electronicTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.When the design of today’s washrooms require higher levels ofhygiene and energy savings, Rada provide the solution.The sensor is recessed into false ceilings or ceiling tiles, and issupplied with a conduit box, front fixings, plate and cover screws.The solenoid valve should be accessible for maintenance purposes.Supplied complete with integral isolator and filter.Electrical SpecificationProtection class: Sensor, electronic module IP55.Supply voltage: 12V AC + 10% 50/60 HZ, via Rada Pulse ControlBox.Operating ambient temperature range: 0°C - 40°C.Maximum humidity: 80%.Wiring from sensor to control box: 2 core PVC covered cable,3.0 m supplied.Sensor range: between 0.50 and 2.5 metres.For details of the Rada Pulse Control Box, refer to the applicabledatasheet. Each Rada Pulse Control Box will accommodate amaximum of 10 operating systems.ApprovalsCE Approved.WRAS approved (Water Regulations Advisory Scheme)Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.Operation SchematicRada PulseControl BoxOperationWhen the sensor is activated, the Rada Pulse Control Box, waits for aperiod of inactivity before, energising the solenoid valve.Solenoid ValveThe solenoid valve opens - allowing water to flow through the outlet.The duration of the flow can be preset, via the Rada Pulse ControlBox, ensuring optimum saving of water and energy.MaterialsBase: ABS, Cover: Polycarbonate.Solenoid Valve: Body material fibreglass polymide.Delay and Flush TimingThe operating systems are programmed remotely , via the Hand HeldProgrammer. The programmer is simply plugged into the control boxthen used to either set up or adjust the flow timings using the easy tofollow menu structure.The programmer can be removed after adjustment to preventunwanted tampering.PressuresSolenoid valve: 0.2 - 10 bar (20 - 1000 kPa).Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5500

More magazines by this user
Similar magazines