Coating systems for cost effective, long term corrosion protection

wattyl.net.au

Coating systems for cost effective, long term corrosion protection

ion 5stile Boldstile RegularCoating systems for cost effective,long term corrosion protection


Epinamel CF602A gloss finish coat for a variety of industrial applications.Used in combination with an appropriate priming system, EpinamelCF602 provides a gloss finish with excellent impact and abrasionresistance. Typically used on concrete floors in industrial environments.Suitable for use as a stand alone system on concrete.Epinamel EB600A versatile high build maintenance buildcoat for steel andconcrete protection.Unlimited recoatability and versatile application methods make thisproduct an ideal choice for use in processing plants and refineries.Used over a suitable primer, this product cures at temperaturesdown to -5°C and may be applied under high relative humidity,up to 95% RH. Full AS2700 colour offer and selected micaceousiron oxide (MIO) colours available. May be topcoated withPoly U400 or Paracryl ® IF540 for superior UV protection.Epinamel NS808A high build, non-skid coating designed for aggressiveenvironments.The coarse non-skid properties make this coating ideal for work boatdecks and heavy industrial situations where occupational slip hazardsare present. May be used as a finish coat or in combination withcoloured finish coats.Epinamel DTM985A surface tolerant, rapid curing, high solids, high build,direct-to-metal, primer/build coat/finish for atmospheric andimmersion applications.A highly versatile and economical maintenance coating for heavyindustrial applications. Well suited for use in mines, off shore rigs,wharf structures and ship hulls to provide long term corrosionprotection. Typically used as a high build, single coat application or incombination with a polyurethane topcoat. Full AS2700 colour rangeand selected MIO colours available.Epinamel MF920A highly abrasion resistant, mineral flake filled, high solids, highbuild, direct-to-metal coating for steel.Designed specifically for areas of extreme wear and abrasion suchas wharfs, drilling rigs, helicopter pads, rolling stock internals andvarious types of heavy equipment. Excellent corrosion protection,chemical resistance and flexibility. Suitable for atmospheric andimmersion situations.Epinamel TL710A high solids, chemical resistant tank lining for protection of steelstructures, concrete floors and steel tanks in aggressive chemicalenvironments.Provides excellent resistance to a wide range of chemicals, refer to theWattyl Tank Lining Resistance Guide for a full list of suitable chemicals.Used in a variety of heavy industrial applications, this high build epoxymay be used direct-to-metal or in combination with an appropriateprimer to increase flexibility during application. Also approved toAS/NZS 4020:2005 for use as a potable water tank lining.Epinamel TL770SFA solvent free, potable water tank lining.Ensures high quality water supply in steel and concrete reservoirsand water tanks. Tested and approved to AS/NZS 4020:2005 by theAustralian Water Quality Centre. Provides excellent coverage in asingle coat high build system. Also suitable for storage of most wastewaters, and saline/sea water. Off white colour provides excellentvisibility during application and for in-service tank inspection.Epinamel UHB1000A 100% solids, ultra high build coating for aggressive marineenvironments.Epinamel UHB1000 is designed principally to provide excellentcorrosion resistance to steel and concrete structures including wharfpiles, work decks, jetties and bridges. It is suitable for new workand maintenance both above and below the waterline in freshand seawater. The coating sets up quickly allowing for applicationbetween tides, with the product continuing to cure under water.Film builds up to 1500 microns are achievable in a single applicationproviding high productivity and maximum protection.For steel in immersion situations, surface preparation of AS/NZS 1627.4 to Sa2 1 / 2 minimum is required and factory manufactured colours only may be used.Epoxies may chalk or discolour on exterior exposure- this does not detract from their performance. Always refer to the appropriate product technical data sheetand material safety data sheet prior to use and ensure that the product is suitable for your application.


Our CommitmentWattyl is a world-class company, providing innovative, quality products to meet thechallenges of Australian and New Zealand industries. We are dedicated to the supply of highquality, cost effective products to improve efficiency and reduce operating costs.Designed and Made in Australia and New ZealandProducts are designed by Wattyl’s team of industrial chemists specifically for Australia andNew Zealand’s harsh and varied environments. Wattyl’s products are manufactured inAustralia and New Zealand supporting the local economy.Our QualityWattyl is committed to quality in the design, production and delivery of its products andservices, and is accredited with ISO9001:2000, NATA and APAS approvals.For the latest product or specification information, customer orders or tospeak to your local industrial specialist contact Wattyl Customer Service onAustralia132 101www.wattyl.com.auNew Zealand0800 735 551www.wattyl.co.nzWattyl, Epinamel and Paracryl are registered trademarks and Poly U is a trademark of Wattyl Australia Pty Ltd. (ABN 40 000 035 914)

More magazines by this user
Similar magazines