RENOLIN PG Series.pdf
RENOLIN PG Series.pdf
RENOLIN PG Series.pdf
- No tags were found...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>RENOLIN</strong> <strong>PG</strong> 100, 150, 220, 320, 460, 680, 1000PI 4-1042ePage 1Fully synthetic polyglycol based gear- and general lubrication oilsDescriptionThe importance of gear- and general lubrication oils based on polyglycols is still growing. The initial raw materials for producingpolyglycol are petroleum and natural gas. Polymers of different chain lengths are produced by the thermal decomposition andsubsequent synthesis of the raw materials. Different viscosity grades can be produced by just changing the chain length of the molecule.The polyglycols obtained using this synthesis have a uniform structure. An optimum adjustment of <strong>RENOLIN</strong> <strong>PG</strong> is obtained by speciallyselected additive combinations.The special properties of the <strong>RENOLIN</strong> <strong>PG</strong> oils are:• very good viscosity-temperature behavior• very good shear stability, shear losses < 1 % acc. to DIN 51 382• high pressure absorption capacity• high wear protection• very low friction coefficient; because of this reduction in operating temperature is possible• very good oxidation stability, high aging resistance• excellent corrosion protection of steel and non-ferrous metals• low foaming characteristics• high flash pointApplications<strong>RENOLIN</strong> <strong>PG</strong> transmission oils are suitable for highly-stressed spur gear, planetary gear and worm gear drives. Applications whenenhanced gliding performance is requested, transmission oils on polyglycol basis have advantages compared to mineral oils.Advantage: Decrease in the oil temperature and the possibility to extended oil change intervals.<strong>RENOLIN</strong> <strong>PG</strong> oils can be used at continuous operating temperatures up to 180°C and in some cases even higher.Products of the <strong>RENOLIN</strong> <strong>PG</strong> series are also used as lubricating oil for compressor handling, process gases like methane, ethane,butane.<strong>RENOLIN</strong> <strong>PG</strong>-oils are not compatible with mineral oils!Approvals<strong>RENOLIN</strong> <strong>PG</strong> is recommended by the Flender company for lubrication of spur gears, bevel gears and planetary gears.PM 4-01/02Previous editions are invalid and should be destroyed.
<strong>RENOLIN</strong> <strong>PG</strong> 100, 150, 220, 320, 460, 680, 1000PI 4-1042ePage 2Fully synthetic polyglycol based gear- and general lubrication oilsTypical PropertiesR E N O L I NProperties Unit <strong>PG</strong> 100 <strong>PG</strong> 150 <strong>PG</strong> 220 Test methodColour - 0,5 0,5 0,5 DIN ISO 2049Density at 15°C kg/m³ 997 1000 1002 DIN 51 757Flashpoint °C 269 258 278 DIN ISO 2592Kinematic Viscosityat 40°C mm²/s 100 150 220 DIN 51 562at 100°C mm²/s 17,2 24,9 35Viscosity Index - 189 200 208 DIN ISO 2909Pour point °C -48 -45 -45 DIN ISO 3016Neutralization number mgKOH/g 0,6 0,6 0,6 DIN 51 558FoamingSequ. I to III24°C immediately/after 10 min ml 10/0 20/0 10/0 ASTM D 89293.5°C immediately/after 10 min ml 10/0 10/0 10/0 ASTM D 89224°C nach 93,5°Cimmediately/after10 min ml 10/0 10/0 10/0 ASTM D 892Copper corrosiondegree ofCorr. 1 - 100 A 3 DIN EN ISO 2160FZG mechanical gear test rig failure loadFZG A/8,3/90 stage > 12 > 12 > 12 DIN 51 354-2FZG micro pitting testGT-C/8,3/90 step-loading test load- G F T h o c h * FVA-InfoblattstageNr. 54/I-IVContinuous load testloadstage G F T h o c h *Steel corrosiondegree of(Corrosion protection) corr. 0-A 0-A 0-A DIN 51 355* Gray discoloration test highPM 4-01/02Previous editions are invalid and should be destroyed.
<strong>RENOLIN</strong> <strong>PG</strong> 100, 150, 220, 320, 460, 680, 1000PI 4-1042ePage 3Fully synthetic polyglycol based gear- and general lubrication oilsTypical PropertiesR E N O L I NProperties Unit <strong>PG</strong> 320 <strong>PG</strong> 460 <strong>PG</strong> 680 <strong>PG</strong> 1000 Test methodColour - 0,5 0,5 0,5 0,5 DIN ISO 2049Density at 15°C kg/m³ 1050 1053 1053 1054 DIN 51 757Flashpoint °C 234 267 264 292 DIN ISO 2592Kinematic Viscosityat 40°C mm²/s 320 460 680 1000 DIN 51 562at 100°C mm²/s 56,2 77,4 115,2 174 DIN 51 562Viscosity Index - 244 251 270 287 DIN ISO 2909Pour point °C -45 -42 -42 -39 DIN ISO 3016Neutralization numberl mgKOH/g 0,6 0,6 0,6 0,6 DIN 51 558FoamingSequ. I to III24°C immediately/after 10 min ml 20/0 10/0 20/0 10/0 ASTM D 89293,5°C immediately/after 10 min ml 5/0 20/0 10/0 10/0 ASTM D 89224°C after 93,5°Cimmediately/after 10 min ml 20/0 10/0 20/0 20/0 ASTM D 892Copper corrosiondegree ofCorr. 1 - 100 A 3 DIN EN ISO 2160FZG mechanicalfailuregear test rigloadFZG A/8,3/90 stage > 12 > 12 > 12 > 12 DIN 51 354-2FZG micro pitting testGT-C/8,3/90step-loading test load stage G F T h o c h * FVA-InfoblattContinuous load test load stage ..............G F T h o c h * Nr. 54/I-IVSteel corrosiondegree of(Corrosion protection) corr. 0-A 0-A 1-A 0-A DIN 51 355* Gray discoloration test highPM 4-01/02Previous editions are invalid and should be destroyed.
Change language