DeviceNet Modules, Series 90-30, Manual, GFK-2196

More documents

Recommendations

Info

4Data Areas TabsThese tabs show the PLC program references assigned to the selected module:These reference assignments can be edited, or left at their defaults. Note thatthe input data area tab shows master inputs, which are module outputs. Theoutput data area tab shows master outputs, which are module inputs. For bothinputs and outputs, data can be configured for both connection 1 andconnection 2.For both inputs and outputs, the offset is the starting address in the master PLCmemory area. It must be less than the size of the data area specified in theNetwork Settings dialog box. To specify data area Size, in the Navigator, rightclickthe DeviceNet slave and choose Network Settings. The DeviceNet SlaveProperties dialog box appears. On the Connection 1 or Connection 2 tab, setthe Size under Resources.The Reference Address is the location in master PLC memory where the data ismapped. This field is read-only if Size is set to 0. This must be a range in %AI,%I, %Q, %G, %AQ, %R, %T, or %M. If the number of bytes (Size) is odd, onlythe discrete addresses (%I, %Q, %G, %M, %T) can be used.Power Consumption TabPower consumptionThis read-only tab shows the backplane power that will be consumed by theDeviceNet Slave Module. This power will be used for module operation.The DeviceNet Slave Module also draws power for its DeviceNet transceiverfrom the 24VDC power supply on the DeviceNet network.4-6 Series 90®-30 Programmable Controller DeviceNet Modules – November 2002 GFK-2196
4Configuring the Network Settings of a DeviceNet Slave ModuleTo configure the Network Settings for a DeviceNet Slave Module, right-click the DeviceNet Slavein the PLC configuration, and choose Network Settings.The Network Settings dialog box appears.The General tab allows setting a name and description for the module. On this tab, you can alsoselect the MACID and Baud Rate. These parameters are also found on the Configuration Parameterscreen; they can be set in either place.The rest of the tabs set up the messaging connections that will be used by the module.Configuring the MAC IDAll software-configured devices originally have the same default MAC ID: 63. Therefore,assigning the MAC ID 63 to be used by a device on the network should be avoided if possible, toprevent duplicate MAC ID conflicts when adding a new slave.GFK-2196 Chapter 4 PLC Configuration for the DeviceNet Slave 4-7
Page 1 and 2: GE Fanuc AutomationProgrammable Con
Page 4 and 5: ContentsCOMMREQ Programming Require
Page 6 and 7: 1DeviceNet Modules for the Series 9
Page 8 and 9: 1Series 90-30 DeviceNet Master Modu
Page 10 and 11: 1Series 90-30 DeviceNet Slave Modul
Page 12 and 13: 1DeviceNet Communications for Serie
Page 14 and 15: 2Power SuppliesWhen using a Series
Page 16 and 17: 2Bus LengthThe maximum length of th
Page 18 and 19: 2GroundingDeviceNet Cable Grounding
Page 20 and 21: 2Module LEDsThe module's three LEDs
Page 22 and 23: Chapter3PLC Configuration for the D
Page 24 and 25: 3Adding a DeviceNet Master Module t
Page 26 and 27: 3Settings tabFault StateTransmissio
Page 28 and 29: 3Network Settings of a DeviceNet Ma
Page 30 and 31: 3Configuring Network Settings for S
Page 32 and 33: 3Configuring a Polled I/O Messaging
Page 34 and 35: 3Configuring a Change-of-State (COS
Page 36 and 37: 3Configuring DeviceNet Explicit Mes
Page 38 and 39: 3Configuring a Polled I/O Messaging
Page 40 and 41: 3Configuring a Change-of-State (COS
Page 42 and 43: 3Configuring DeviceNet Explicit Mes
Page 44 and 45: 4Configuration StepsThere are three
Page 46 and 47: 4Configuring the Parameters of a De
Page 50 and 51: 4Configuring I/O Messaging Connecti
Page 52 and 53: 4Configuring a Strobed I/O Messagin
Page 54 and 55: 4Configuring a Cyclic I/O Messaging
Page 56 and 57: Chapter5Module OperationThis chapte
Page 58 and 59: 5The DeviceNet Master Module stores
Page 60 and 61: 5Fault Table Entries for a Series 9
Page 62 and 63: 5Device Status Bits for the Series
Page 64 and 65: 6COMMREQs for the Series 90-30 Devi
Page 66 and 67: 6Format of the Communication Reques
Page 68 and 69: 6Corrective Actions for COMMREQ Err
Page 70 and 71: 6Command Code 9: Reading Identifica
Page 72 and 73: 6Runtime Error Codes in the Module
Page 74 and 75: 6Command Code 4: Getting the Status
Page 76 and 77: 6Command Code 5: Getting Status Inf
Page 78 and 79: 6Command Code 6: Getting Input Stat
Page 80 and 81: 6Command Codes 1 & 7: Sending a Dev
Page 82 and 83: 6Word # Dec (Hex) Description1 0001
Page 84 and 85: 6Send Device Explicit Extended, Dat
Page 86 and 87: 6Command Codes 2, 3 & 8: Reading an
Page 88 and 89: 6Reading a DeviceNet Custom-Explici
Page 90 and 91: 6Command Codes 3 & 8: Replying to a
Page 92 and 93: 6Command Code 8: Send Server Explic
Page 94 and 95: 7Identity ObjectObject Class 0x01Th
Page 96 and 97: 7DeviceNet ObjectObject Class 0x03T
Page 98 and 99:
7Connection ObjectObject Class 0x05
Page 100 and 101:
7PLC Data ObjectObject Class 0x64Nu
Page 102 and 103:
AppendixADeviceNet EDS FilesThis se
Page 104 and 105:
IndexAACK timeout, 3-5, 4-5Add Devi
show all

DeviceNet Modules, Series 90-30, Manual, GFK-2196

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?