User's Manual - doc-station.ru

More documents

Recommendations

Info

SD-TestBus 2 v. 2.16 During the transfer of the data to the device, for each item modified will be visualized the indication "old_value-- -> new_value" (e.g. "10 ---> 12") to indicate that the writing operation is under execution. When the writing is completed the indication will change in "new_value". For sending the data it is necessary to be an “authorized” user. The default password is 0001. For more details see section Error! Reference source not found.. WARNING: the sending to the device of some value arrangements (e.g. not cong<strong>ru</strong>ent protection threshold) may cause an error message. In this case the page will be refreshed with the relay current value. Note 1: when the device under test is in the local operating modality , all the writing commands are disabled. Note 2: to cancel the modifications in the selections it is sufficient to press the pushbutton “Reset”. Note 3: according to the type of selected voice, TEST, SETTINGS, etc. it is possible to print a test report and to save/load the relay settings in the menu “File”. ABB SACE ABB SD-TestBus2 v. 2.16 1SDH000602R0002 L2937 EN 22 di 28
SD-TestBus 2 v. 2.16 7.6.1 Current time curve With some relays it is possible to have a graphical representation of the protection set (L, S, I and G protections). To open this window you have to push the button named “Curve current / time”. On the menu bar is made possible to print the current view, to change the current scale (Ampere or In) and to close the window. Note 1: the I1 current threshold is drawn at about 117% (IEC) or 105% (UL) of its nominal value. This is done according to the respective standards. Note 2: it is possible to change the protection set without close the window. At the end of the programming session, the window is automatically refreshed with the new parameters. If there is a communication problem or an incoherent parameter set a “?” icon is shown. 7.7 Communication settings (only for PR222DS/PD and PR223EF) This page is visualized only if the device found on the bus belongs is a PR222DS/PD or PR223EF. Here is some information about the configuration of the communication unit. ABB SACE ABB SD-TestBus2 v. 2.16 1SDH000602R0002 L2937 EN 23 di 28
Page 1 and 2: SD-TestBus 2 v. 2.16 User’s Manua
Page 3 and 4: SD-TestBus 2 v. 2.16 1 Introduction
Page 5 and 6: SD-TestBus 2 v. 2.16 Open the "Clie
Page 7 and 8: SD-TestBus 2 v. 2.16 It shoes the p
Page 9 and 10: SD-TestBus 2 v. 2.16 3.3.1.3 Print
Page 11 and 12: SD-TestBus 2 v. 2.16 PR122/P @ 3 ti
Page 13 and 14: SD-TestBus 2 v. 2.16 4 Bus scanning
Page 15 and 16: SD-TestBus 2 v. 2.16 At the end of
Page 17 and 18: SD-TestBus 2 v. 2.16 6 Find master
Page 19 and 20: SD-TestBus 2 v. 2.16 7.2 Alarms All
Page 21: SD-TestBus 2 v. 2.16 7.5 Run time m
Page 25 and 26: SD-TestBus 2 v. 2.16 7.9 Signaling
Page 27 and 28: SD-TestBus 2 v. 2.16 8 SD-View2000

User's Manual - doc-station.ru

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?