Pneumatic Tubing Fittings - Bay Port Valve & Fitting

GENERAL INFORMATION on LEGRIS PUSH-IN FITTINGSCConnection:1. Make sure the tubing end iscut square.2. Push the tubing into the fittinguntil it stops. Tubing is nowheld and sealed.3. Pull on the tubing to verify.Disconnection:1. Make sure there is no air flow.2. Press the release ring towardsthe fitting and pull the tubingout. No tools required.General Instructions:• Make sure the tubing end is cut square and free of burrs or contamination.• Avoid kinking the tubing, or side stress against the collet, which may cause leaking.• Tighten threaded fittings by hand, using a wrench on the hex to finish tightening.NOTE: These fittings are designed for use with Compressed Air ONLY.LEGRIS NICKEL-PLATED BRASS PUSH-IN FITTINGSTechnical Characteristics:• Service temperature: -4º F to +250º F• Pressure: vacuum to + 290 PSI• Thread: length of threads in accordance with ISO 7.1 standards• Thread sealant on all NPT threadsMaterials of Construction:• High Phosphorous Electroless: Nickel-plated Brass• O-ring Seal: Buna Nitrile• Button: Polypropylene• Sealing Washers: Nylon• NO SiliconeApplications:• Various fluids: compressed air, fluids, compatible with materials of construction.• Typical industries: automotive, packaging, paper mills, wood working, factories with washdownprocesses.• Tube Compatibility: Urethane, Nylon, Polyethylene, Teflon, metallic tubes (Stainless Steel& Copper).4 Dixon Valve & Coupling, 800-355-1991 Pneumatic Tubing Fittings

LEGRIS NICKEL-PLATED BRASS FITTINGSMale Connector(Tube to Male NPT)Tube O.D. Male NPT Part # Pkg Qty5/32" 10-32* 3201 04 20 105/32" 1/8" 3275 04 11 105/32" 1/4" 3275 04 14 101/4" 10-32* 3201 56 20 101/4" 1/8" 3275 56 11 101/4" 1/4" 3275 56 14 101/4" 3/8" 3275 56 18 103/8" 1/8" 3275 60 11 103/8" 1/4" 3275 60 14 103/8" 3/8" 3275 60 18 103/8" 1/2" 3275 60 22 101/2" 3/8" 3275 62 18 101/2" 1/2" 3275 62 22 10* UNF - Straight thread; Supplied with gasket5/32"5/32"1/4"1/4"3/8"3/8"1/2"1/2"Female Connector(Tube to Female NPT)TubeO.D. Female NPT Part #1/8"1/4"1/8"1/4"1/4"3/8"3/8"1/2"3215 04 113215 04 143215 56 113215 56 143215 60 143215 60 183215 62 183215 62 22Pkg Qty1010101010101010CMale Elbow Swivel(Tube to Male NPT)Tube O.D. Male NPT Part # Pkg Qty5/32"5/32"5/32"1/4"1/4"1/4"3/8"3/8"3/8"1/2"10-32*1/8"1/4"1/8"1/4"3/8"1/4"3/8"1/2"1/2"3299 04 203209 04 113209 04 143209 56 113209 56 143209 56 183209 60 143209 60 183209 60 223209 62 2210101010101010101010* UNF - Straight thread; Supplied with gasketMale Run Swivel Tee(Tube to Male NPT)Tube O.D. Male NPT Part # Pkg Qty5/32"5/32"5/32"1/4"1/4"1/4"3/8"3/8"3/8"1/2"10-32*1/8"1/4"1/8"1/4"3/8"1/4"3/8"1/2"1/2"3293 04 203203 04 113203 04 143203 56 113203 56 143203 56 183203 60 143203 60 183203 60 223203 62 2210101010101010101010* UNF - Straight thread; Supplied with gasketEqual Union(Tube to Tube)Tube O.D. Part # Pkg Qty5/32"1/4"3/8"1/2"3206 04 003206 56 003206 60 003206 62 0010101010Union Elbow(Tube to Tube)Tube O.D. Part # Pkg Qty5/32"1/4"3/8"1/2"3202 04 003202 56 003202 60 003202 62 0010101010Union Tee(Tube to Tube)Tube O.D. Part # Pkg Qty5/32"1/4"3/8"1/2"3204 04 003204 56 003204 60 003204 62 0010101010Pneumatic Tubing FittingsDixon Valve & Coupling, 800-355-19915

LEGRIS NYLON/NICKEL-PLATED BRASS FITTINGSTubeO.D.1/8"1/8"1/8"1/8"5/32"5/32"5/32"1/4"1/4"1/4"1/4"5/16"5/16"5/16"3/8"3/8"3/8"3/8"1/2"1/2"1/2"Male Elbow(Tube to Male NPT)MaleNPT10-32*1/16"1/8"1/4"10-32*1/8"1/4"10-32*1/8"1/4"3/8"1/8"1/4"3/8"1/8"1/4"3/8"1/2"1/4"3/8"1/2"Part #310953203109530831095311310953143109042031090411310904143109562031095611310956143109561831090811310908143109081831096011310960143109601831096022310962143109621831096222PkgQty101010101010101010101010101010101010101010* UNF - Straight thread; Supplied withgasketTubeO.D.1/8"1/8"5/32"5/32"1/4"1/4"5/16"5/16"3/8"3/8"3/8"Female Connector(Tube to Female NPT)FemalePart #NPT1/8"1/4"1/8"1/4"1/8"1/4"1/8"1/4"1/8"1/4"3/8"3014531130145314301404113014041430145611301456143014081130140814301460113014601430146018PkgQty1010101010101010101010TubeO.D.1/8"5/32"5/32"1/4"1/4"5/16"5/16"3/8"1/2"Female Elbow(Tube to Female NPT)FemalePart #NPTTubeO.D.1/8"1/8"1/8"5/32"5/32"1/4"1/4"1/4"5/16"5/16"5/16"3/8"3/8"3/8"3/8"1/2"1/2"1/2"1/8"1/8"1/4"1/8"1/4"1/8"1/4"1/4"3/8"300953113009041130090414300956113009561430090811300908143009601430096218Male Connector(Tube to Male NPT)MaleNPT1/16"1/8"1/4"1/8"1/4"1/8"1/4"3/8"1/8"1/4"3/8"1/8"1/4"3/8"1/2"1/4"3/8"1/2"Part #317553083175531131755314317504113175041431755611317556143175561831750811317508143175081831756011317560143175601831756022317562143175621831756222PkgQty101010101010101010PkgQty101010101010101010101010101010101010CPneumatic Tubing FittingsDixon Valve & Coupling, 800-355-19917

FLOW CONTROL VALVESPush-to connect, uni-directional flow control valves, with one-piece design, for controlling the speed of a cylinder byregulating air exhaust. Intake air flows freely through the flow control and exhaust air is metered out through a speciallydesigned fine adjustment screw. Control Pressure Range: 15 to 135 PSI. Temperature Range: 30°F to 160°F.CTubeO.D.5/32"1/4"1/4"3/8"3/8"CompactFlow Control ValveNPTSize1/8"1/8"1/4"1/4"3/8"Part #7065041170655611706556147065601470656018PkgQty1010101010TubeO.D.5/32"5/32"1/4"1/4"1/4"Miniature ExhaustFlow Control ValveNPTSize10-32*1/8"10-32*1/8"1/4"Part #7660042076600411766056207660561176605614PkgQty1010101010* UNF - Straight thread; Suppliedwith gasketPush-to connect flow control valve for use where cylinder access is difficult or another fitting is attached to thecylinder port. Stackable using 2 joining clips supplied, or panel mountable using exisiting holes.Working Pressure Range: 15 to 145 PSI.In-LineFlow Control ValveTubeO.D.5/32"1/4"3/8"1/2"Part #77700400777056007770600077706200PkgQty10101010Allows air to pass in one direction while blocking flow in the other direction. A pressure of more than 7.3 PSI willovercome the spring pressure and allow flow. An arrow indicates free flow direction.Maximum Working Pressure: 145 PSI.TubeO.D.5/32"6mm1/4"5/16"Non-ReturnIn-Line ValvePart #79960400799606007996560079960800PkgQty10101010Pneumatic Tubing FittingsDixon Valve & Coupling, 800-355-19919

METRIC PUSH-IN FITTINGS & TUBINGMaterials: Nickel-plated Brass construction. Black bodyis glass-filled Nylon; Buna-N O-Ring seal; Polypropylenerelease button. Silicone free.Positive Seal: Sealing and holding is accomplishedinstantaneously.Reusable: Connect and disconnect numerous times.Full Flow: Fitting seals on outside diameter of tubing.Working Pressure: Fittings rated to 275 PSI at ambienttemperature.Maximum Working Temperature: 175°FPre-applied thread sealant on all male pipe threads.Compatible Tubing: Semi-rigid Nylon, Polyurethaneand Polyethylene tube.Gripping Ring TechnologyQuick Connect and Disconnect:Simply push tubing in. To remove, pressthe release ring towards the fitting andpull tubing out. No tools required.CTubeO.D.4mm4mm6mm6mm8mm8mmMale Connector(Tube to Male BSPT)MaleBSPT1/8"1/4"1/8"1/4"1/8"1/4"Part #317504103175041331750610317506133175081031750813PkgQty101010101010TubeO.D.4mm4mm6mm6mm8mm8mmFemale Connector(Tube to Female BSPP)FemaleBSPP1/8"1/4"1/8"1/4"1/8"1/4"Part #311404103114041331140610311406133114081031140813PkgQty101010101010TubeO.D.4mm4mm6mm6mm8mm8mm4mm6mm8mmMale Elbow(Tube to Male BSPT)MaleBSPTSizeO.D.xxx1/8"1/4"1/8"1/4"1/8"1/4"4mm31090410 10WallWorkingI.D. Thickness Length Part # Pressure31090413 104mm31090610 106mm31090613 106mm31090810 108mm31090813 108mm2.7 mm4mm6mmPart #.65 mm1 mm1 mmPkgQty25m25m25m1025P04001025P06001025P0800275280210• Resistant to fungus, abrasion, moisture and UV radiation.• Temperature range -60°F to 200°F at 75°F (highertemperatures lower working pressures)• Translucent colorTubeO.D.Male Branch Tee(Tube to Male BSPT)MaleBSPT1/8"1/4"1/8"1/4"1/8"1/4"Part #310804103108041331080610310806133108081031080813PkgQty101010101010METRIC NYLON TUBING ROLLSPneumatic Tubing FittingsDixon Valve & Coupling, 800-355-199111

D.O.T. PUSH-IN FITTINGS & TUBINGMaterials:• Body(straights) tube supports and grippers: Brass CA360.• Forged Elbows and Tees: Brass CA377.• "O" Ring: Buna N.• Thread Sealant: Loctite 516.Working Pressure: Vacuum to 150 PSI.Working Temperature: -40°F to +200°F.Threads: NPTF standard.Compatible Tubing: Designed for use with SAE J844 NylonTubing. Meets Department Of Transportation FMVSS-106.TubeO.D.1/4"1/4"1/4"3/8"3/8"TubeO.D.1/4"1/4"Swivel Male Elbow(Tube to Male NPT)MaleNPT1/8"1/4"3/8"1/4"3/8"Part #AQ69DOTS4x2AQ69DOTS4x4AQ69DOTS4x6AQ69DOTS6x4AQ69DOTS6x6Swivel Male Run Tee(Tube to Male NPT)MaleNPT1/8"1/4"Part #AQ71DOTS4x2AQ71DOTS4x4PkgQty101010105PkgQty105Swivel Male Branch Tee(Tube to Male NPT)TubeO.D.1/4"1/4"MaleNPT1/8"1/4"Part #AQ72DOTS4x2AQ72DOTS4x4D.O.T. AIR BRAKE TUBINGHOSE COUPLING SAFETYSizeO.D.1/4"1/4"1/4"3/8"3/8"PkgQty105LengthAQ69DOT4x2AQ69DOT4x4AQ69DOT6x43/8" 100' Red J844-06-R-100 150Meets Department Of Transportation FMVSS-106.Nylon Material conforming to SAE J844.Dixon's couplings and retention devices are designed to work safely for their intended use. The selection of the proper hose, coupling andretention device, and the proper application of the coupling to the hose are of utmost importance.Users must consider the size, temperature, application, media, pressure and hose and coupling manufacturer's recommendations whenselecting the proper hose assembly components. Dixon recommends that all hose assemblies be tested in accordance with the RubberManufacturers Association's recommendations and be inspected regularly (before each use) to ensure that they are not damaged or havebecome loose.Where safety devices are integral to the coupling, they must be working and utilized. The use of supplementary safety devices such as safetyclips or safety cables are recommended.If any problem is detected, couplings must be removed from service immediately.Dixon is available to consult, train and recommend the proper selection and application of all fittings we sell. We strongly recommend thatdistributors and end users make use of Dixon's Testing and Recommendation Services. Dixon can be contacted at 1-800-355-1991.© 2002 DVCC PTB5011P15M100'100'100'100'100'TubingColorBlackBlueRedBlackBlueTubeO.D.1/4"1/4"3/8"TubeO.D.1/4"1/4"1/4"3/8"3/8"Part #Male Elbow(Tube to Male NPT)MaleNPT1/8"1/4"1/4"Part #Male Connector(Tube to Male NPT)MaleNPT1/8"1/4"3/8"1/4"3/8"TubeO.D.1/4"3/8"TubeO.D.1/4"3/8"J844-04-BL-100J844-04-B-100J844-04-R-100J844-06-BL-100J844-06-B-100Part #AQ68DOT4x2AQ68DOT4x4AQ68DOT4x6AQ68DOT6x4AQ68DOT6x6Union Connector(Tube to Tube)Part #AQ62DOT4AQ62DOT6Union Tee(Tube to Tube)Part #AQ64DOT4AQ64DOT6WorkingPressure150150150150150$PkgQty101010PkgQty101051010PkgQty1010PkgQty1010