Domnick Hunter Compressed Air Dryers - regula servis

More documents

Recommendations

Info

Saving energy with the dewpoint dependentswitching (DDS) energy management systemThe energy required to regenerate the off-line desiccant bed in an absorption dryer is constant, and based upon theassumption that the dryer is operating at its full capacity and the desiccant bed requiring regeneration has been fullysaturated. In reality, a dryer is rarely operating at full capacity all of the time, for example during shift work and periodsof low demand. Daily and seasonal fluctuations in ambient temperature and humidity also change the moisture loadingplaced upon the dryer.Under such conditions, at the point in the drying cycle where the air flow is switched from one drying chamber to theother, there is the potential for drying capacity to remain in the desiccant material about to undergo regeneration. As theenergy used to regenerate this partially saturated bed is based upon the assumption that the bed is fully saturated, moreenergy (purge air) is consumed than is actually necessary.Dewpoint Dependent Switching (DDS) Energy Management SystemWith the DDS Energy Management system installed, the drying cycle remains unchanged, however as the dryingchambers are about to change, the DDS system overrides normal operation to fully utilise the drying capacity of theon-line desiccant material.DDS operationAt column changeover, the exhaust valve is closed to allow the purge air tore-pressurise the off-line column, thus ensuring no loss of system pressure.At this time, both drying chambers are at full line pressure, so that no purgeair is being used and the dryer is in a state of zero energy consumption.Under normal operation, the drying chambers would proceed to change overautomatically, however the DDS energy management system incorporates ahygrometer which is used to monitor the pressure dewpoint of the air leavingthe dryer. If the air is drier than the pre-set dewpoint, the desiccant material isonly partially saturated and has drying capacity remaining within it, thereforechange over is delayed.The hygrometer constantly monitors the outlet dewpoint until the pre-set levelhas been achieved, at which point, change over will occur.The drying and regenerating cycle will then continue normally until the endof the next column changeover when the DDS energy management systemmay again extend the drying period as dictated by the outlet air quality.DDS Operation - Energy Saving Cycle (Heatless Dryer example shown)Time(minutes)Side A0 2.5 3RegenerationDDS Drying / Regeneration Cyclechangeover time dictatedby outlet dewpointEnergy SavingSide B Drying Regenerationchangeover0 2.5 3RepressurisationRepressurisationDryingchangeover time dictatedby outlet dewpointEnergy SavingchangeoverUsing DDS will ensure that the energy consumed by PNEUDRI is directly proportional to the actual air flow, temperatureand moisture loading, not the dryers rated capacity, thus providing significant energy and environmental savings.DDS Energy Saving (Heatless Dryer example shown)Air Demand % Energy Saving %Energy SavingP/A KwEnvironmental SavingP/A Kg CO 2100 33.00 95,040 40,86790 40.00 115,200 49,53680 47.00 135,360 58,20570 53.00 152,640 65,63560 60.00 172,800 74,30450 66.00 190,080 81,7349System pressure 6 bar g. Max Temp 35°C. System flow 1700 m 3 /hr (1000 cfm). Average pressure 6.5 bar g. Average Temp 30°C.
Dryer control systemsPNEUDRI ControllersDRYER MODELCONTROLLERMiDAS (DAS) MIDI (DME) MAXI (MX) MAXI (MPX) MAXI (DH)MiDAS•Smart Smart DDS• • Electronic• •AdvancedPneumatic• •PNEUDRI Controller FeaturesControllerOptionsPower onIndicationFaultIndicationDisplay faultconditionvaluesServiceintervalIndicationFUNCTIONServicecountdowntimersConfigurablealarmsettingsRemote VoltFree AlarmContactsFilter ServiceTimerDDS EnergyMgmtSystemMiDAS• •Smart• • • •Smart DDS• • • • •Electronic• • • • • • • • •Advanced• • • • • • • • •PneumaticIf you would like more information about these or other rangesof Parker domnick hunter purification products please visit:www.domnickhunter.com, Email: dhindsales@parker.com orcontact your local Parker domnick hunter representative.Compressed AirCapabilities17 400 4401PNEUDRIMiDAS17 400 4407PNEUDRIMIDIplus17 400 4408OIL-X EVOLUTIONFilters17 400 4402PNEUDRIMX17 400 4410PNEUDRIMPX17 400 4411PNEUDRIHeat Regenerative17 400 4409MAXIGASNitrogen Generators17 400 470410
Page 4 and 5: The PNEUDRI modular designThe PNEUD
Page 6 and 7: Air qualityAdsorption dryers remove
Page 8 and 9: PNEUDRI OperationDrying of Compress
Page 12 and 13: PNEUDRI MPXHeatless (PSA) Regenerat
Page 14 and 15: Technical DataDryerModelsMin Operat
Page 16 and 17: Dryer PerformanceDryer ModelsDewpoi
Page 18 and 19: PNEUDRI DHHeat Regenerative (TSA) R
Page 20 and 21: Technical DataDryerModelsMin Operat
Page 22 and 23: Dryer PerformanceDryer ModelsDewpoi
Page 24 and 25: PNEUDRI MiDASA totally clean and dr
Page 26: Technical DataDryerModelsMin Operat

Domnick Hunter Compressed Air Dryers - regula servis

Create successful ePaper yourself

Delete template?

Save as template?