ABB industrial drives ACS880, single drives 0.55 ... - VAE ProSys sro

More documents

Recommendations

Info

$\ATS\schemi\ATS con S3-S4-S5\Rm002101.dwg - VAE ProSys sro$

du/dt filtersdu/dt filtering suppresses inverter output voltage spikesand rapid voltage changes that stress motor insulation.Additionally, du/dt filtering reduces capacitive leakagecurrents and high frequency emission of the motor cable aswell as high frequency losses and bearing currents in themotor. The need for du/dt filtering depends on the motorinsulation. For information on the construction of the motorinsulation, consult the manufacturer.If the motor does not fulfil the following requirements, thelifetime of the motor might decrease. Insulated N-end (nondrivenend) bearings and/or common mode filters are alsorequired for motor bearing currents with motors bigger than100 kW. For more information, please see the ACS880hardware manuals.Please see below about how to select a filter according to themotor.Filter selection table for ACS880Motor type Nominal AC supplyvoltageABB motorsRandom-woundM2__, M3__ andM4__Form-woundHX__ and AM__Old 1) form-woundHX__ and modularRandom-woundMotor insulation systemRequirements forABB du/dt and common mode filters, insulated N-end motor bearingsP N< 100 kW andframe size < IEC 315P N< 134 hp andframe size < NEMA 500U N≤ 500 V Standard _ + N500 V 150 m)Reinforced _ + N380 V < U N≤ 690 V Standard n/a + N + CMF380 V < U N≤ 690 V Check with the motormanufacturerHX__ and AM__ 2) 500 V < U N≤ 690 V fiber glass taping+ du/dt + N + CMF0 V < U N≤ 500 V Enmelled wire with + N + CMFHDPConsult the motor manufacturer.+ du/dt with voltages over 500 V + N + CMF1) Manufactured before 1.1.1998.2)For motors manufactured before 1.1.1998, check for additional instructions with the motor manufacturer.100 kW ≤ P N< 350 kW orIEC 315 ≤ frame size < IEC 400134 hp ≤ P N< 469 hp orNEMA 500 ≤ frame size ≤ NEMA 580Non-ABB motorsRandomwoundand formwoundU N≤ 420 V Standard Û LL= 1300 V _ + N or CMF420 V < U N≤ 500 V Standard Û LL= 1300 V + du/dt + du/dt + N or+ du/dt + CMForReinforced: Û LL= 1600 V, _+ N or CMF0.2 microsecond rise time500 V < U N≤ 600 V Reinforced: Û LL= 1600 V + du/dt + du/dt + N or+ du/dt + CMForReinforced: Û LL= 1800 V _ + N or CMF600 V < U N≤ 690 V Reinforced: Û LL= 1800 V + du/dt + du/dt + NReinforced: Û LL= 2000 V, _+ N or CMF0.3 microsecond rise timeThe abbreviations used in the table are defined belowAbbr. DefinitionU NÛ LLP Ndu/dtCMFNn/aNominal AC line voltage.Peak line-to-line voltage at motor terminals which the motor insulation must withstand.Motor nominal power.du/dt filter at the output of the drive. Available from ABB as an optional add-on kit.Common mode filter. Depending on the drive type, CMF is available from ABB as a factory-installed option (+208) or as an optional add-on kit.N-ned bearing: insulated motor non-drive end bearing.Motors of this power range are not available as standard units. Consult the motor manufacturer.30 ABB industrial drives ACS880 single drives | Catalog
du/dt filtersExternal du/dt filters for ACS880-01ACS880 du/dt filter type (3 filters included in kits marked* ) )Unprotected (IP00) Protectedto IP22Protectedto IP54NOCH0016-60NOCH0030-60NOCH0070-60NOCH0120-60* )FOCH0260-70FOCH0320-50NOCH0016-62NOCH0030-62NOCH0070-62NOCH0120-62NOCH0016-65NOCH0030-65NOCH0070-65NOCH0120-65400 V 500 V 690 V02A4-3 02A1-5 x x x03A3-3 03A0-5 x x x03A4-5 x x x04A0-3 04A8-5 x x x05A6-3 05A2-5 x x x07A2-3 07A6-5 07A3-7 x x x09A4-3 09A8-7 x x x12A6-3 11A0-5 x x x14A2-7 x x x014A-5 x x x017A-3 018A-7 x x x021A-5 022A-7 x x x025A-3 026A-7 x x x027A-5 x x x032A-3 034A-5 035A-7 x x x038A-3 040A-5 042A-7 x x x045A-3 052A-5 049A-7 x x x061A-3 x x x065A-5 061A-7 x x x072A-3 077A-5 x x x087A-3 084A-7 x x x105A-3 096A-5 098A-7 x x x124A-5 119A-7 x145A-3 156A-5 142A-7 x169A-3 180A-5 174A-7 x206A-3 240A-5 210A-7 x246A-3 260A-5 271A-7 x293A-3 x363A-3 361A-5 x430A-3 414A-5 xApplicabilitySeparate du/dt filters are available for ACS880-01.Unprotected IP00 filters must be placed into an enclosurethat provides an adequate degree of protection.Factory-installed du/dt filters are available for theACS880-07. They are installed inside the drive cabinet.Dimensions and weights of the du/dt filtersdu/dt filter Height Width Depth Weight(mm) (mm) (mm) (kg)NOCH0016-60 195 140 115 2.4NOCH0016-62/65 323 199 154 6NOCH0030-60 215 165 130 4.7NOCH0030-62/65 348 249 172 9NOCH0070-60 261 180 150 9.5NOCH0070-62/65 433 279 202 15.5NOCH0120-60 3) 200 154 106 7NOCH0120-62/65 765 308 256 45NOCH0260-60 3) 383 185 111 12FOCH0260-70 382 340 254 47FOCH0320-50 662 319 293 65FOCH0610-70 662 319 293 653)3 filters included, dimensions apply for one filter.NOCH0016-62NOCH0016-60NOCH0016-65 FOCH0610-70Catalog | ABB industrial drives ACS880 single drives 31
Page 1 and 2: Low voltage AC drivesABB industrial
Page 3 and 4: The all-compatibleACS880 series dri
Page 5 and 6: Single drives, ACS880The all-compat
Page 7 and 8: Process all-compatibleThe drives ar
Page 9 and 10: Business all-compatibleThe new all-
Page 11 and 12: Wall-mounted single drives, ACS880-
Page 13 and 14: Ratings, types and voltagesWall-mou
Page 15 and 16: Ratings, types and voltagesCabinet-
Page 17 and 18: Standard interface and extensions f
Page 19 and 20: Application control programsOur app
Page 21 and 22: PC tool for easy startup and mainte
Page 23 and 24: Drive application programming with
Page 25 and 26: Input/output extension modules for
Page 27 and 28: Brake optionsBrake chopperThe brake
Page 29: Brake options, ACS880-07U N = 400 V
Page 33 and 34: Catalog | ABB industrial drives ACS
Page 35 and 36: Summary of features and optionsPowe
Page 37 and 38: Secure uptime throughout the drive
Page 39 and 40: NotesCatalog | ABB industrial drive

ABB industrial drives ACS880, single drives 0.55 ... - VAE ProSys sro

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?