Rada individual showers

jhplumb.com

Rada individual showers

individual showeringrada 415 fc pressure balancing Mixing valve• Surface mounted• Service friendly - supplied with integralstrainers and easy change plug-in cartridge• Easy to install• Connection to 15 mm compression or ½” BSP fittings• Reversed inlet connections supported• Adjustable elbows to allow top,bottom or rear entry pipeworkSpecify as: Rada 415 fc (1.1542.018)½” surface mounted pressure balancing mixing valve, incorporatingintegral inlet elbows to accept either rising, falling or back inletsupplies.Dimensions (mm)Flow Diagram5Ø9235Ø153 Ø188.5Pressure Loss - bar432113500 5 10 15 20 25Flow Rate - l/minKohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


individual showeringTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.ConnectionsInlets: 15 mm compression/½” BSP male fitting connections to acceptrising, falling or back inlet supplies.Outlet: ½” BSP male/female.WeightProduct Gross Weight (Kgs) Total PackagedWeight (Kgs)Rada 415 fc 2.040 2.403Standard connections are hot-left, cold-right, outlet-top when facingthe controlApprovalsWRAS approved (Water Regulations Advisory Scheme).Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.OperationAnti-clockwise rotation of the control knob alters temperatures fromfull cold to a pre-set maximum temperature, which can be set uponcommissioning.If required, a maximum temperature override facility is available.A red button on the perimeter of the control knob, which is locked intoposition when despatched, can be unlocked upon commissioning.The button can be pressed to enable further rotation of the knob, toobtain higher temperatures than the pre-set maximum temperature.Flow ControlThe Rada 415 fc requires a separate outlet flow control.MaterialsBody and Inlet Elbows: Corrosion resistant copper alloy.Control knobs and trims: Polished stainless steel and chrome platedengineering plastic.Temperature RangeThe blend temperature obtainable is between full cold and full hot,and is therefore dependant upon the supply temperatures.Under normal operating conditions and with stable supplytemperatures, temperature control is maintained to within ±1°C ofthe temperature selected for up to a 50% pressure change in eithersupplyPressuresMinimum maintained pressure: 1.0 barMaximium maintained pressure: 5.0 barMaximum static pressure: 10.0 barKohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P2804/7


i/tlindividual showeringrada exact-3 thermostatic Mixing valve• TMV3 Thermostatic Mixing Valve Scheme Approved• Service friendly - supplied with integral strainers andeasy change plug-in cartridge• Surface mounted• Easy to install• Connection to 15 mm compression or ½” BSP fittings• Reversed inlet connections supported• Adjustable elbows to allow top, bottom or rear entrypipeworkSpecify as: Rada Exact-3 (1.0.408.01.3)Dimensions (mm)½” exposed thermostatic shower control, incorporating Radathermservice-free cartridge. Pre-set maximum temperature stop. This32153Shown with a fallingoutlet. Can be arising outlet whenused with a rigid riser.28553380product can also be used with a rising outlet when fixed to Rada er-s310 kit, or VR145 and Rada Riser.Specify as: Rada Exact-3 ev (1.0.409.48.1)As above, only supplied with Mira Response exposed variable showerfittings.9455Flow Diagram5252Hydraulic restriction: Flow rate/Pressure loss graph(shower control only, equal dynamics supply pressures, unrestrictedoutlet and blend temperature setting.1250332max.305 max.332max.n )40600600ML(30Exact 3e75030R a20w250 max.oF103320 in anydirection000.5 1.0 1.5 2.0 2.5 3.0 3.5Rada er-s 310 fittingsPressure Loss (Bar)Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


individual showeringTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.ConnectionsInlets: 15 mm compression.Reversible outlet connector: ½” BSP male or 15 mm compression(compression nut and olive may be required for the exposed models).Standard connections are hot-left, cold-right, bottom outlet whenfacing the control.ApprovalsBuildcert TMV3 Thermostatic Mixing Valve Scheme approved:LP-S - Low Pressure ShowerHP-S - High Pressure ShowerCertificate No: ETC/22/0897.Complies with the technical requirements of BS7942 for the samedesignations.Buildcert TMV2 Thermostatic Mixing Valve Scheme approved:LP-S Low Pressure showerHP-S High Pressure ShowerCertificate No: BC197/0406Designed to comply with European Standards EN1111 and EN1287.WRAS approved (Water Regulations Advisory Scheme).Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.OperationAll V8/3 valves (excluding ‘lockshield’ model) are operated via asingle sequential control which when rotated, initially opens the valve,then increases the temperature from cold through to a pre-settablemaximum temperature stop.Outlet blend temperature is maintained within 2°C with a 10°C changein hot or cold supply.Shutdown of outlet flow to seepage within 3 seconds in the eventof failure in either the hot or cold water supply, providing the blendtemperature differs from the inlet supply temperature by at least 10°C.The valve will maintain control with a pressure loss ratio of up to 10:1.PressuresFor optimum performance, maintained supply pressures should benominally equal.Minimum maintained pressure 0.1 bar*Maximum static pressure: 10 barMaximum pressure loss ratio **: 10:1 (in favour of either supply)* 1 metre head from underside of cold tank to outlet of shower fitting.* * Pressure loss ratio is determined by subtracting the resistance toflow of the outlet pipework and outlet fittings (generally known as the‘back pressure’, and measured at the outlet of the mixing valve) fromthe dynamic pressures of the hot and cold water at the inlets of themixing valve. This is at its extreme when the mixing valve is beingused at its lowest flow rate and when the maximum inequality occursin the pressure of the hot and cold water supplies.WeightProduct Gross Weight (Kgs) Total PackagedWeight (Kgs)Meynell V8/3 3.000 3.228Meynell V8/3 L 3.000 3.230Meynell V8/3 K 3.000 3.230Meynell V8/3 - ev 4.500 4.993MaterialsBody: DZR brass chrome plated.Temperature RangeFactory preset maximum outlet temperature: 42°C.Minimum temperature differential between hot inlet and preset outlettemperature: 10°C.Optimum temperature control range: 35°C - 45°C.Maximum hot water temperature: 85°C (for safety reasons it isrecommended that hot water storage temperature is maintained atbetween 60°C to 65°C in ablutionary applications).The performance specification outlined below is achieved with outletblend temperature set between 35°C - 45°C and supplies of 15°Ccold and 65°C hot with nominally equal pressures:Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P3229/6


individual showeringmeynell v6 thermostatic mixerßßßßßProven thermostatic performanceSafe thermostatic shutdown in less than 3 secondsSuitable for use on all plumbing systemsExposed versionSingle sequential control for ease of useSpecify as: Meynell V6 (PESM0540P)½” exposed single sequential thermostatic mixing valve.Specify as: Meynell V6-ev (PESM0562P)½” exposed single sequential thermostatic mixing valve with showerfittings including single mode handset, slide rail, hose, soap dish andhose retaining ring.Dimensions (mm)Flow Diagram137110353011015551535Flow Rate – l/min25201510500 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0Pressure Loss – barKohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


individual showeringTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.ConnectionsInlets: 15 mm compression.Outlet connector: ½” BSP male or 15 mm compression.Compression nut and olive may be required for the outlet connector ofthe exposed model if used in conjunction with a Rada riser pipe andVR145 head.ApprovalsDesigned to comply with European Standards EN1111 and EN1287.WRAS Approved (Water Regulations Advisory Scheme).Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.OperationAll V6 valves are operated via a single sequential control which whenrotated, initially opens the valve, then increases the temperature fromcold through to a preset maximum.PressuresFor optimum performance, maintained supply pressures should benominally equal.Minimum maintained pressure 0.1 bar*Maximum static pressure: 10 barMaximum pressure loss ratio**: 5:1 (in favour of either supply)* 1 metre head from underside of cold tank to outlet of shower fitting.** Pressure loss ratio is determined by subtracting the resistance toflow of the outlet pipework and outlet fittings (generally known as the‘back pressure’, and measured at the outlet of the mixing valve) fromthe dynamic pressures of the hot and cold water at the inlets of themixing valve. This is at its extreme when the mixing valve is beingused at its lowest flow rate and when the maximum inequality occursin the pressure of the hot and cold water supplies.WeightProduct Gross Weight (Kgs) Total PackagedWeight (Kgs)Meynell V6 1.500 1.773Meynell V6 ev 3.000 3.626Wax capsule thermostatic technology ensures that constantshowering temperatures are maintained over a varying range of inlettemperatures.MaterialsBody: DZR brass chrome plated.Temperature RangeFactory preset maximum outlet temperature: 42°C.Minimum temperature differential between hot inlet and preset outlettemperature: 10°C.Optimum temperature control range: 35°C - 45°C.Maximum hot water temperature: 85°C (for safety reasons it isrecommended that hot water storage temperature is maintained atbetween 60°C to 65°C in ablutionary applications).The performance specification outlined is achieved with outlet blendtemperature set between 35°C - 45°C and supplies of 15°C cold and65°C hot with nominally equal pressures:- Outlet blend temperature is maintained within 3°C with a 10°Cchange in hot or cold supply.- Shutdown of outlet flow to seepage within 3 seconds in the eventof failure in either the hot or cold water supply, providing theblend temperature differs from the inlet supply temperature by atleast 10°C.- The valve will maintain control with a pressure loss ratio of up to5:1, with open outlet.Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P3230/5


individual showeringIndividual showering - applicationsIndividual Showering - Dual Control - TMV3 ApprovedA commercial range of ‘built-in’ and‘exposed’ individual thermostaticshower valves. Examples shown are ofboth dual and single sequential control.Rada bsr-s/300Dual Control - TMV3 ApprovedDual Control feature separate flow andtemperature controls.Rada Exact-3BRada Exact-3 evwith Mira Response FittingsIndividual Showering - Single Sequential ControlRada VR105Single Sequential ControlCombined sequential lever operatedtemperature selection and ‘on/off’ flowcontrol.Rada er-s 310Meynell V6BMeynell V8/3Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


individual showeringIndividual showering - applicationsIndividual Showering with Timed Flow Control - Mechanical - TMV3 ApprovedRada VR105‘Built-in’ and ‘exposed’ thermostaticmixing valves allowing individualtemperature selection with separate,non-concussive, mechanical timed flowvalves of approximately 30 secondsduration.Rada TF503bRada VR145Rada 215-t3bcRada TF503Rada 215-t3 cIndividual Showering with Timed Flow Control - Electronic - TMV3 ApprovedRada SV1015Rada bsr-s/300Rada 120 Sensor‘Built-in’ thermostatic mixing valveallowing individual temperature control.No-touch sensor and solenoid valveoperation with programmable timedflow control.Note: The location of the solenoidvalve in an accessible duct or void isnecessary.Rada 215-t3bcKohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P3884/2


individual showeringmeynell v4 single point thermostatic shower mixer• Reliable thermostatic performance• Indepedent flow and temperature controls forease of use• Suitable for high pressure applications• Attractive, contemporary design• Supplied with ½” BSP offset inlet connectorsSpecify as: Meynell V4 Thermostatic Shower Mixer (1.1577.002)½” exposed, dual control, thermostatic shower valve. Shower fittingsavailable seperately.Specify as: Mira Select UV Fittings Chrome (1.1541.008)Mira React adjustable spray handset with three different sprayactions, hose, clamp bracket, soap dish, slide bar, hose retaining ringand additional low capacity spray plate.Specify as: Mira Verve UV Fittings Chrome (1.1540.218)Mira Response adjustable spray handset with three different sprayactions, hose, clamp bracket, soap dish, slide bar, hose retaining ringand additional low capacity spray plate.Dimensions (mm)Flow Diagram150 ± 25301107062 diaFlow Rate - l/min2010002 4 6Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


individual showeringTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.ConnectionsInlet: Offset connectors (½” BSP male connection, ¾” BSP maleconnection to shower).Outlet: ½” BSP male connection.WeightProduct Gross Weight (Kgs) Total PackagedWeight (Kgs)Meynell V4 2.500 2.970Dimensions (mm)ApprovalsDesigned to comply with European Standards EN1111 and EN1287.WRAS approved (Water Regulations Advisory Scheme).Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems54285 maxMeynell V4 with Mira Select UVFittings - chromeOperationThe Meynell V4 thermostatic shower mixer provides accuratetemperature control and easy flow rate adjustment. The MeynellV4 is precision engineered to consistently deliver water at a safetemperature. The product responds to changes in the pressure ortemperature of the incoming water in order to maintain the selectedoutput temperature.600MaterialsBody: Chrome plated brass.Control knobs and trims: Chrome plated engineering plastic.Temperature RangeMinimum temperature differential between hot supply and outlettemperature: 10 °C.Optimum temperature control range of mixer: 35 °C - 45 °C.Minimum hot water supply temperature: 55 °C.Maximum hot water supply temperature: 80 °C52Meynell V4 with Mira Verve UVFittings - chromeThe performance specification outline below is achieved with theblend set between 35°C and 45°C, with supply temperatures of 15°Ccold and 65°C hot and nominally equal inlet supply pressures.332 maxOutlet blend temperature is maintained within 2°C with a 10°C change600in the hot or cold supply.Thermostatic shut down to seepage in approximately five seconds ifthe cold supply fails. Shut down to seepage is only achieved if the hotsupply is 10°C above the blend temperature.PressuresMaintained supply pressures should be nominally equal.Maximum pressure loss ratio: 5:1.Minimum maintained pressure: 0.5 bar.Maximum maintained pressure: 5.0 bar.Maximum static pressure: 10 bar.Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P4217/1


individual showeringrada revive-3 thermostatic shower valve• Enhanced thermostatic performance - TMV3approved for high pressure applications• Independent flow and temperature controls for easeof use• Service friendly - supplied with non-return valves,integral strainers and sealed for life temperaturecartridge• Attractive, contemporary design• Easy to install - supplied with variable inletconnectors and wall mounting support bracketSpecify as: Rada Revive-3 Thermostatic Shower (1.1577.001)½” exposed, dual control, thermostatic shower valve incorporatingservice-free temperature cartridge, ceramic disc flow control cartridgeand check valves and strainers, housed in a brass body.Shower fittings available seperately.Specify as: Mira Select UV Fittings Chrome (1.1541.008)Mira React adjustable spray handset with three different sprayactions, hose, clamp bracket, soap dish, slide bar, hose retaining ringand additional low capacity spray plate.Dimensions (mm)150 ± 1570 dia80 min32 maxSpecify as: Mira Verve UV Fittings Chrome (1.1540.218)Mira Response adjustable spray handset with three different sprayactions, hose, clamp bracket, soap dish, slide bar, hose retaining ringand additional low capacity spray plate.Flow Diagram25Flow Rate - l/min201510500 0.5 1.0 1.5 2.0 2.5 3.0 3.5Pressure loss - barKohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


individual showeringTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.ConnectionsInlet: Offset connectors (½” BSP male connection, ¾” BSP maleconnection to shower).Outlet: ½” BSP male connection.ApprovalsBuildcert TMV3 Thermostatic Mixing Valve Scheme approved:HP-S - High Pressure ShowerCertificate No: BC 080/0204Complies with the technical requirements of BS7942 for the samedesignations.Designed to comply with European Standards EN1111 and EN1287.WRAS approved (Water Regulations Advisory Scheme).Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systemsapproximately five seconds if the cold supply fails. Shut down toseepage is only achieved if the hot supply is 12°C above the blendtemperature.PressuresOptimum maintained pressure: 1.0 bar.Maximum maintained pressure: 5.0 bar.Minimum maintained pressure: 0.5 bar.Maximum static pressure: 10 bar.Maximum flow rate: 25 l/min. (valve only).Dimensions (mm)54285 maxOperationThe Rada Revive-3 provides accurate temperature control andeasy flow rate adjustment. The Revive-3 is precision engineeredto consistently deliver water at a safe temperature. The productresponds to changes in the pressure or temperature of the incomingwater in order to maintain the selected output temperature.600MaterialsBody: Chrome plated brass.Control knobs and trims: Chrome plated engineering plastic.Temperature RangeMinimum temperature differential between hot supply and outlettemperature: 10 °C.Optimum temperature control range of mixer: 35 °C - 45 °C.Minimum hot water supply temperature: 55 °C.Maximum hot water supply temperature: 80 °CThe performance specification outline below is achieved with theblend set between 35°C and 45°C, with supply temperatures of 15°Ccold and 65°C hot and nominally equal inlet supply pressures.Revive Revive-3 with Mira Select UV Fittings - chrome52332 max600The blended temperature is maintained within 1°C with a 12°Cchange in the hot or cold supply.The blended water temperature is maintained within 1°C when thepressure between the inlet and outlet is halved (defined as a pressureloss ratio 2:1) on either the hot or cold side.The valve will maintain temperature control with a pressure loss ratioof up to 10:1.The wax capsule sensor effects a shut down to seepage inRevive Revive-3 with Mira Verve UV Fittings - chromeKohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P4283/1


individual showeringmeynell v8/3 b thermostatic mixer• TMV3 approved for use in healthcare applications• Also approved to the TMV2 standard for residentialuse• High flow rates at low pressures• Reliable thermostatic performance• Safe thermostatic shutdown in less than 2 seconds• Suitable for use on all plumbing systems• Built-in and long lever versions available• Single sequential control for ease of useSpecify as: Meynell V8/3 B (PRSM0563P)½” built-in single sequential thermostatic mixing valve. Suppliedcomplete with integral strainers.Specify as: Meynell V8/3 BL (PRSM0625P)½” built-in single sequential thermostatic mixing valve with long leverfor disabled use. Supplied complete with integral strainers.Dimensions (mm)Specify as: Meynell V8/3 B-biv (PRSM0564P)½” built-in single sequential thermostatic mixing valve with showerfittings, including multi-mode handset, slide rail, hose, hoseconnecting elbow, soap tray and hose retaining ring. Suppliedcomplete with integral strainers.16155 Max35 Min15Flow Diagram1565Flow Rate - l/min4540353025201510500 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.035Pressure loss - bar117 122.5Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


individual showeringTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.ConnectionsInlets: 15 mm compression.Reversible outlet connector: ½” BSP male or 15 mm compressionStandard connections are hot-left, cold-right, top outlet when facingthe control.ApprovalsBuildcert TMV3 Thermostatic Mixing Valve Scheme approved:LP-S - Low Pressure ShowerHP-S - High Pressure ShowerCertificate No: ETC/22/0897.Complies with the technical requirements of BS7942 for the samedesignations.Buildcert TMV2 Thermostatic Mixing Valve Scheme approved:LP-S Low Pressure ShowerHP-S High Pressure ShowerCertificate No: BC197/0406Designed to comply with European Standards EN1111 and EN1287.WRAS approved (Water Regulations Advisory Scheme).Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.OperationAll V8/3 valves (excluding ‘lockshield’ model) are operated via asingle sequential control which when rotated, initially opens the valve,then increases the temperature from cold through to a pre-settablemaximum temperature stop.in hot or cold supply.Shutdown of outlet flow to seepage within 3 seconds in the eventof failure in either the hot or cold water supply, providing the blendtemperature differs from the inlet supply temperature by at least 10°C.The valve will maintain control with a pressure loss ratio of up to 10:1.PressuresFor optimum performance, maintained supply pressures should benominally equal.Minimum maintained pressure 0.1 bar*Maximum static pressure: 10 barMaximum pressure loss ratio**: 10:1 (in favour of either supply)* 1 metre head from underside of cold tank to outlet of shower fitting.** Pressure loss ratio is determined by subtracting the resistance toflow of the outlet pipework and outlet fittings (generally known as the‘back pressure’, and measured at the outlet of the mixing valve) fromthe dynamic pressures of the hot and cold water at the inlets of themixing valve. This is at its extreme when the mixing valve is beingused at its lowest flow rate and when the maximum inequality occursin the pressure of the hot and cold water supplies.WeightProduct Gross Weight (Kgs) Total PackagedWeight (Kgs)Meynell V8/3 B 3.500 3.730Meynell V8/3 BL 3.500 3.890Meynell V8/3 B - biv 5.500 5.993MaterialsBody: DZR brass chrome plated.Temperature RangeFactory preset maximum outlet temperature: 42°C.Minimum temperature differential between hot inlet and preset outlettemperature: 10°C.Optimum temperature control range: 35°C - 45°C.Maximum hot water temperature: 85°C (for safety reasons it isrecommended that hot water storage temperature is maintained atbetween 60°C to 65°C in ablutionary applications).The performance specification outlined below is achieved with outletblend temperature set between 35°C - 45°C and supplies of 15°Ccold and 65°C hot with nominally equal pressures:Outlet blend temperature is maintained within 2°C with a 10°C changeKohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5335


individual showeringrada 415 fbc pressure balancing Mixing valve• Recessed version• Service friendly - supplied with integralstrainers and easy change plug-in cartridge• Easy to install• Connection to 15 mm compression or ½” BSP fittings• Reversed inlet connections supportedSpecify as: Rada 415 fbc (1.1542.019)½” recessed pressure balancing mixing valve for connection toconcealed pipework.Dimensions (mm)Flow Diagram135 592 A/F35Ø76132 A/FØ163Pressure Loss - bar432157 to 7400 5 10 15 20 25Flow Rate - l/minKohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


individual showeringTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.The Rada 415 fbc is designed for connection to concealed pipework.PressuresMinimum maintained pressure: 1.0 barMaximum maintained pressure: 5.0 barMaximum static pressure: 10.0 barConnectionsInlets: 15 mm compression/½” BSP male fitting connections.Outlet: ½” BSP male/female.Standard connections are hot-left, cold-right, outlet-top when facingthe control.WeightProduct Gross Weight (Kgs) Total PackagedWeight (Kgs)Rada 415 fbc 1.850 2.213ApprovalsWRAS approved (Water Regulations Advisory Scheme).Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management SystemsOperationAnti-clockwise rotation of the control knob alters temperatures fromfull cold to a pre-set maximum temperature, which can be set uponcommissioning.If required, a maximum temperature override facility is available.A red button on the perimeter of the control knob, which is locked intoposition when despatched, can be unlocked upon commissioning.The button can be pressed to enable further rotation of the knob, toobtain higher temperatures than the pre-set maximum temperature.Flow ControlThe Rada 415 fbc requires a separate outlet flow control.MaterialsBody and Inlet Elbows: Corrosion resistant copper alloy.Control knobs and trims: Polished stainless steel and chrome platedengineering plastic.Temperature RangeThe blend temperature obtainable is between full cold and full hot,and is therefore dependant upon the supply temperatures.Under normal operating conditions and with stable supplytemperatures, temperature control is maintained to within ±1°C ofthe temperature selected for up to a 50% pressure change in eithersupply.Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5477


i/tlindividual showeringrada exact-3 b thermostatic Mixing valve• TMV3 Thermostatic Mixing Valve Scheme Approved• Service friendly - supplied with integral strainers andeasy change plug-in cartridge• Recessed, for use with concealed pipework• Easy to install• Connection to 15 mm compression or ½” BSP fittings• Reversed inlet connections supportedDimensions (mm)168Specify as: Rada Exact-3 B chrome (1.0.427.02.1)½” built-in thermostatic shower control, for concealed pipework,incorporating Radatherm service-free cartridge, ceramic disc flowcontrol cartridge and check valve and strainer cartridges, housedwithin a chrome plated DZR brass body. This product can also beused with a rigid shower head such as VR105 or BSR-S 300 showerfitting.5535Specify as: Rada Exact-3 B white (1.0.427.01.1)As above, only supplied with white control levers and concealingplate.25211759Specify as: Rada Exact-3 B-biv white (1.0.427.03.1)12As above, only supplied with Mira Response built-in variable showerfittings.Flow Diagram7260052155332max.6005212332max.Hydraulic restriction: Flow rate/Pressure loss graph(shower control only, equal dynamics supply pressures, unrestrictedoutlet and blend temperature setting.)n5040Mo20 in anydirectionL(eaR3020Exact 3 B250 max.woF1030 oRada bsr-s 300 fittings000.5 1.0 1.5 2.0 2.5 3.0 3.5Pressure Loss (Bar)Kohler Mira LimitedSpecification EnquiriesCromwell RoadTel: 01242 282527CheltenhamFax: 01242 282404GloucestershireEmail: rada_technical@mirashowers.comGL52 5EPwww.radacontrols.com


individual showeringTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.The Rada Exact-3 B is designed to be built-in and connect toconcealed pipework.Incorporates the patented “Radatherm” cartridge, a unique sealed-forlifeunit, utilising materials of proven durability for extended servicefreereliability.The shower control inlets contain check valves and filters andare both housed within readily accessible cartridges for easymaintenance.ConnectionsInlets: 15 mm compression/½” BSP male fitting connections to acceptrising, falling or back inlet supplies.Outlet: 15 mm compression/½” BSP external union.Standard connections are hot-left, cold-right, outlet-top when facingthe control.Note! Should the inlet supplies be reversed then the shower controlwill not be able to control temperature. This can be corrected byreversing the position of the Radatherm cartridge within the controlbody.ApprovalsBuildcert TMV3 Thermostatic Mixing Valve Scheme approved:HP-S - High Pressure ShowerLP-S - Low Pressure ShowerCertificate No: ETC/14/0597.Complies with the technical requirements of BS7942 for the samedesignations.Designed to comply with European Standards EN1111 and EN1287.WRAS approved (Water Regulations Advisory Scheme).Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.OperationThe top control knob controls the flow, whilst the bottom control knobcontrols the temperature.The temperature controls allow the user to select the requiredtemperature within the range available. An integral temperature stoplimits the maximum temperature to a preset level and can only bereset by an authorised person.MaterialsBody: DZR brass.Concealing Plates: Zinc alloy and chrome plated or white engineeringplastic.Temperature and Flow Control Knobs: Zinc alloy and chrome plated.Lever Controls and Trims: White engineering plastic.Temperature RangeThe maximum temperature that can be selected is set atapproximately 43°C when despatched, but this can be reset on site asrequired.Minimum temperature differential, blend to either supply is 12°C.Optimum thermostatic control range: 35°C - 45°C.Minimum cold water temperature: 1°C.Maximum hot water temperature: 85°C.Note! The mixing valve can accept temporary temperature excursionsabove 85°C without damage, however operation of the mixing valveat such elevated supply temperatures is not recommended. Forreasons of general safety, hot water storage temperatures shouldbe maintained at between 60°C - 65°C where serving ablutionaryapplications.Pressures/Flow RatesMinimum flow rate: 3 l/min at mid-blend and equal supply pressures.Maximum flow rate: 35 l/min at mid-blend (which equates to amaximum pressure loss of 3.0 bar).Maximum pressure loss ratio*: should not exceed 10:1 in favour ofeither supply during flow.Minimum dynamic supply pressure: 0.15 bar.Maximum dynamic supply pressure: 5 bar.Maximum static pressure: 10.0 barNote! Both hot and cold pressure should be nominally equal* Pressure loss ratio is determined by subtracting the resistance toflow of the outlet pipework and outlet fittings (generally known as the‘back pressure’, and measured at the outlet of the mixing valve) fromthe dynamic pressures of the hot and cold water at the inlets of themixing valve. This is at its extreme when the mixing valve is beingused at its lowest flow rate and when the maximum inequality occursin the pressure of the hot and cold water supplies.WeightProduct Gross Weight (Kgs) Total PackagedWeight (Kgs)Rada Exact-3 B 3.240 3.481Rada Exact-3 B3.240 3.481whiteRada Exact-3 B-biv 3.718 4.784whiteKohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5478


individual showeringmeynell v6 B thermostatic shower mixer• Proven thermostatic performance• Safe thermostatic shutdown• Suitable for use on all plumbing systems• Built-in version• Single sequential control for ease of useSpecify as: Meynell V6 B (PRSM0540P)½” built-in single sequential thermostatic mixing valve.Specify as: Meynell V6 B-biv (PRSM0562P)½” built-in single sequential thermostatic mixing valve with showerfittings including single mode handset, slide rail, hose, hoseconnecting elbow, soap dish and hose retaining ring.Dimensions (mm)Flow Diagram15850 Max30 Min1535301555Flow Rate – l/min252015109811035500 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0Pressure Loss – barKohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


individual showeringTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.ConnectionsInlets: 15 mm compression.Outlet connector: ½” BSP male or 15 mm compression.ApprovalsDesigned to comply with European Standards EN1111 and EN1287.WRAS Approved (Water Regulations Advisory Scheme).Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management Systems.OperationAll V6 valves are operated via a single sequential control which whenrotated, initially opens the valve, then increases the temperature fromcold through to a preset maximum.Wax capsule thermostatic technology ensures that constantshowering temperatures are maintained over a varying range of inlettemperatures.PressuresFor optimum performance, maintained supply pressures should benominally equal.Minimum maintained pressure 0.1 bar*Maximum static pressure: 10 barMaximum pressure loss ratio**: 5:1 (in favour of either supply)* 1 metre head from underside of cold tank to outlet of shower fitting.** Pressure loss ratio is determined by subtracting the resistance toflow of the outlet pipework and outlet fittings (generally known as the‘back pressure’, and measured at the outlet of the mixing valve) fromthe dynamic pressures of the hot and cold water at the inlets of themixing valve. This is at its extreme when the mixing valve is beingused at its lowest flow rate and when the maximum inequality occursin the pressure of the hot and cold water supplies.WeightProduct Gross Weight (Kgs) Total PackagedWeight (Kgs)Meynell V6 B 2.000 2.223Meynell V6 B-biv 3.500 4.126MaterialsBody: DZR brass chrome plated.Temperature RangeFactory preset maximum outlet temperature: 42°C.Minimum temperature differential between hot inlet and preset outlettemperature: 10°C.Optimum temperature control range: 35°C - 45°C.Maximum hot water temperature: 85°C (for safety reasons it isrecommended that hot water storage temperature is maintained atbetween 60°C to 65°C in ablutionary applications).The performance specification outlined below is achieved with outletblend temperature set between 35°C - 45°C and supplies of 15°Ccold and 65°C hot with nominally equal pressures:- Outlet blend temperature is maintained within 3°C with a10°C change in hot or cold supply.- Shutdown of outlet flow to seepage within 3 seconds inthe event of failure in either the hot or cold water supply, providingthe blend temperature differs from the inlet supply temperature byat least 10°C.- The valve will maintain control with a pressure loss ratio of up to5:1, with open outlet.Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5479


COMMERCIAL Shower panelrada 15tf / 15TFW• Pre-plumbed shower panel with integral(concealed) TMV3 approved thermostaticmixing valve, push button timed flow control& vandal resistant shower head• Safe temperature control• Concealed pipe-work which protects usersfrom high surface temperatures• Long, sleek design – suitable for all ages and abilities• Robust & durable materials used throughout• Easy to install and maintain - Integralisolators & flexible connections provided• Satin stainless steel or whitepowder coated panel finish• For connection to hot & cold suppliesDimensions (mm)Specify as: Rada PA-15TF Shower Panel Assembly (1.1613.044)Ready to install satin finish stainless steel panel with hot and coldwater pipe entry connecting to a concealed Meynell 15/3 TMV3approved thermostatic mixing valve feeding a Rada TF503 pushbutton timed flow control and Rada VR105 vandal resistant chromeplated shower head with integral strainer, flow regulator and withadjustable spray angle option.1217Specify as: Rada PA-15TFW Shower Panel Assembly (1.1613.045)Ready to install white powder coated stainless steel panel with hotand cold water pipe entry connecting to a concealed Meynell 15/3TMV3 approved thermostatic mixing valve feeding a Rada TF503push button timed flow control and Rada VR105 vandal resistantchrome plated shower head with integral strainer, flow regulator andwith adjustable spray angle option..192 156Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


commercial showeringTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.Quick and easy to install and service. Each panel supplied with15mm isolating ball valves on inlets as standard. All componentsthat require routine test and maintenance are easily accessible.ConnectionsInlet: 15mm compression to both hot and cold water inlet pipe.ApprovalsBuildcert TMV3 Thermostatic Mixing Valve Scheme approved:-LP-S Low Pressure ShowerHP-S High Pressure ShowerCertificate No. ETC/200/1202Complies with the technical requirements ofBS7942 for the same designations.Designed to comply with European Standards EN1111 and EN1287.WRAS approved (Water Regulations Advisory Scheme).Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:1996 Environmental Management Systems.OperationThe flow cycle is activated by pressing the flow button. Theflow rate is constant and is automatically turned off afterapproximately 30 seconds. Further economy of water usagecan be achieved by means of an internal flow rate adjuster.MaterialsPanel Case: Brushed stainless steel or white powder coated finish.Stainless steel braided flexible hoses withEPDM liner used throughout.Meynell 15/3 thermostatic mixing valve: DZR brassTimed flow control: Body and some internal componentsare manufactured from copper alloys.Other internal components are made from engineering plasticsShower head: Chromium plated copper alloybody and engineering plastic spray plate.Temperature RangeFactory pre-set maximum outlet temperature: 42 °COptimum thermostatic control range: 35 °C - 45 °CRecommended hot: 55 °C - 65 °CRecommended cold: 5 °C - 20 °CMaximum hot: 85 °CPressuresMinimum maintained pressure with 9 l/min flowregulator fitted in shower head: 0.5 barMinimum maintained pressure with flow regulators removed: 0.2 barMaximum static pressure: 7.0 barApplicationFor leisure centres, sports clubs, schools, healthcarefacilities, factories, prisons, military establishments, etc,where safe fixed temperature control, vandal resistanceand water economy are prime requirements.Long slim line panel aids wall coverage. Particularly suitablefor upgrading existing surface mounted shower installationsas no chasing out of walls or breaking of tiles is required.Flow Diagram14.012.010.0Flow Rate - L/min8.06.04.02.000 1.0 2.0 3.0 4.0 5.0Pressure - Barwith flow regulatorswithout flow regulatorsWeightProduct Gross Weight (Kgs) Total PackagedWeight (Kgs)Rada PA - 15TF/TFW 8.60 10.20Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© March 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5573


Commercial Shower panelPA - 215TF / PA - 215TFW• Pre-plumbed shower panel with integraladjustable TMV3 approved thermostaticmixing valve, push button timed flow control& vandal resistant shower head• User temperature selection(up to safe, pre-set maximum)• Concealed pipe-work which protects usersfrom high surface temperatures• Long, sleek design – suitable for all ages and abilities• Robust & durable materials used throughout• Easy to install and maintain - Integralisolators & flexible connections provided• Satin stainless steel or whitepowder coated panel finish• For connection to hot & cold suppliesDimensions (mm)Specify as: Rada PA-215TF Shower Panel Assembly (1.1613.046)Ready to install satin finish stainless steel panel with hot and coldwater pipe entry connection to a Rada 215-t3 TMV3 approvedthermostatic mixing valve, with adjustable temperature selection,feeding a Rada TF503 push button timed flow control and RadaVR105 vandal resistant chrome plated shower head with integralstrainer, flow regulator and with adjustable spray angle option1217Specify as: Rada PA-215TFW Shower Panel Assembly (1.1613.047)Ready to install white powder coated stainless steel panel withhot and cold water pipe entry connection to a Rada 215-t3 TMV3approved thermostatic mixing valve, with adjustable temperatureselection, feeding a Rada TF503 push button timed flow controland Rada VR105 vandal resistant chrome plated shower head withintegral strainer, flow regulator and with adjustable spray angle option.192 156Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


commercial showeringTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.Quick and easy to install and service. Each panel supplied with15mm isolating ball valves on inlets as standard. All componentsthat require routine test and maintenance are easily accessible.ConnectionsInlet: 15mm compression to both hot and cold water inlet pipeApprovalsBuildcert TMV3 Thermostatic Mixing Valve Scheme approved:-LP-S Low Pressure ShowerHP-S High Pressure ShowerCertificate No. ETC/179/0602Complies with the technical requirements ofBS7942 for the same designations.Designed to comply with European Standards EN1111 and EN1287.WRAS approved (Water Regulations Advisory Scheme).Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:1996 Environmental Management Systems.OperationThe flow cycle is activated by pressing the flow button. Theflow rate is constant and is automatically turned off afterapproximately 30 seconds. Further economy of water usagecan be achieved by means of an internal flow rate adjuster.Showering temperature can be selected (up to apre-set maximum temperature) via rotary control knob.MaterialsPanel Case: Brushed stainless steel or stainlesssteel white powder coated finish.Stainless steel braided flexible hoses withEPDM liner used throughoutRada 215-t3 thermostatic mixing valve: Body is of chromeplatedDZR brass with chrome-plated knob.Timed flow control: Body and some internal componentsare manufactured from copper alloys. Other internalcomponents are made from engineering plastics.Shower head: Chromium plated copper alloybody and engineering plastic spray plate.PressuresMinimum maintained pressure with 9 l/min flowregulator fitted in shower head: 0.5 barMinimum maintained pressure with flow regulators removed: 0.2 barMaximum static pressure: 7.0 barApplicationFor leisure centres, sports clubs, schools, healthcarefacilities, factories, military establishments, etc, wheresafe adjustable temperature control, vandal resistanceand water economy are prime requirements.Long slim line panel aids wall coverage. Particularly suitablefor upgrading existing surface mounted shower installationsas no chasing out of walls or breaking of tiles is required.Flow Diagram14.012.0Flow Rate - L/min10.08.06.04.0001.0 2.0 3.0 4.0 5.0Pressure - Barwith flow regulatorswithout flow regulatorsWeightProductGross Weight(Kgs)Total PackagedWeight (Kgs)Rada PA - 215TF/TFW 9.70 11.30Temperature RangeOptimum thermostatic control range: 35 °C - 45 °CRecommended hot: 55 °C - 65 °CRecommended cold: 5 °C - 20 °CMaximum hot: 85 °CKohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© March 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5574


Commercial Shower panelPA - V8F / V8FW• Pre-plumbed shower panel with integral TMV3approved thermostatic mixing valve with flowand temperature adjustment and with easy cleansingle spray handset, flexible hose and slide bar• User selection of flow and temperature(up to a safe, pre-set maximum)• Concealed pipe-work which protects usersfrom high surface temperatures• Long, sleek design – suitable for all ages and abilities• Robust & durable materials used throughout• Easy to install and maintain - Integralisolators & flexible connections provided• Satin stainless steel or whitepowder coated panel finish• For connection to hot & cold suppliesDimensions (mm)Specify as: Rada PA-V8F Shower Panel Assembly (1.1613.048)Ready to install satin finish stainless steel panel with hot and coldwater pipe entry connecting to a Meynell V8/3 TMV3 approvedthermostatic mixing valve, having independent flow and temperaturecontrol, with easy clean single spray handset, flexible hose and robustslide bar with easy to use slide mechanism.Specify as: Rada PA-V8FW Shower Panel Assembly (1.1613.049)Ready to install white powder coated stainless steel panel withhot and cold water pipe entry connecting to a Meynell V8/3 TMV3approved thermostatic mixing valve, having independent flow andtemperature control, with easy clean single spray handset, flexiblehose and robust slide bar with easy to use slide mechanism.121745192 490Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


commercial showeringTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.Quick and easy to install and service. Each panel supplied with15mm isolating ball valves on inlets as standard. All componentsthat require routine test and maintenance are easily accessible.PressuresMinimum maintained pressure with 9 l/min flowregulator fitted in shower head: 0.5 barMinimum maintained pressure with flow regulators removed: 0.2 barMaximum static pressure: 7.0 bar.ConnectionsInlet: 15mm compression to both hot and cold water inlet pipe.ApprovalsBuildcert TMV3 Thermostatic Mixing Valve Scheme approved:-LP-S Low Pressure ShowerHP-S High Pressure ShowerCertificate No. ETC/188/0902Complies with the technical requirements ofBS7942 for the same designations.Designed to comply with European Standards EN1111 and EN1287.WRAS approved (Water Regulations Advisory Scheme).Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:1996 Environmental Management Systems.OperationFlow and temperature (up to a pre-set maximum) isadjusted via single sequential lever control.Water delivery is via a easy clean single spray handset with flexiblehose and robust slide bar with easy to use slide mechanism.ApplicationFor gymnasia, sports clubs, halls of residence, healthcarefacilities, etc, where user choice of temperature andflow control is preferred and water delivery via a showerhandset and flexible hose is a requirement.Long slim line panel aids wall coverage. Particularly suitablefor upgrading existing surface mounted shower installationsas no chasing out of walls or breaking of tiles is required.Flow Diagram20.018.016.0Flow Rate - L/min14.012.010.08.06.0MaterialsPanel Case: Brushed stainless steel or white powder coated finishStainless steel braided flexible hoses withEPDM liner used throughoutMeynell V8/3 thermostatic mixing valve: Body is of chromeplatedDZR brass with chrome-plated lever knob.Slide bar is manufactured from brushed stainless steel.All other components are manufactured from whitecoloured engineering plastics and polymers.4.02.000Weight1.0 2.0 3.0 4.0 5.0Pressure - Barwith flow regulatorswithout flow regulatorsTemperature RangeOptimum thermostatic control range: 35 °C - 45 °CRecommended hot: 55 °C - 65 °CRecommended cold: 5 °C - 20 °CMaximum hot: 85 °CProductGross Weight Total Packaged(Kgs)Weight (Kgs)Rada PA - V8TF/TFW 9.80 11.40Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© March 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5575


individual/group showeringRada 215-t3 C thermostatic mixing valve• Approved for use in all UK healthcare premises• Features the unique “Radatherm”service-free cartridge• Unbeatable temperature control• Complete with check valves and strainersSpecify as: Rada 215-t3 c (1.0.440.01.1)½” thermostatic mixing valve incorporating Radatherm service-freecartridge, check valves and strainers. Housed within swivel elbows,featuring 15 mm compression connectors, which can be converted to½” BSP union if required.Dimensions (mm)Flow Diagram1855015365Flow Rate - I/min40302010113033 00.51.0Pressure Loss – bar1.5 2.0Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


individual/group showeringTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.ConnectionsInlet and Outlet: ½” BSP external union or 15 mm compression (nutand olive provided).Standard connections are hot (left), cold (right), top outlet.ApprovalsBuildcert TMV3 Thermostatic Mixing Valve Scheme approved:LP-S - Low Pressure ShowerHP-S - High Pressure ShowerCertificate No: ETC/14/0597.Complies with the technical requirements of BS7942 for the samedesignations.Designed to comply with European Standards EN1111 and EN1287.WRAS approved (Water Regulations Advisory Scheme).Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management SystemsOperationRada 215-t3 series mixing valves do not have integral flow control;appropriate provision must be made for this in the outlet pipework.This can be in the form of basin/bath tap, stopcock, mechanicaltimed-flow controller or solenoid. The device chosen must be nonconcussivein operation.Pressures/Flow RatesMinimum dynamic supply pressure: 0.15 bar.Maximum dynamic supply pressure: 5 bar.Minimum flow rate:3 l/min at mid blend.Maximum flow rate: 35 l/min at mid blend (which equates to amaximum pressure loss of 1.8 bar).Maximum pressure loss ratio*: 10:1 (in favour of either supply).Maximum static pressure: 10 bar.Note! Both hot and cold pressure should be nominally equal.* Pressure loss ratio is determined by subtracting the resistance toflow of the outlet pipework and outlet fittings (generally known as‘back pressure’, and measured at the outlet of the mixing valve) fromthe dynamic pressures of the hot and cold water at the inlets of themixing valve. This is at its extreme when the mixing valve is beingused at its lowest flow rate and when the maximum inequality occursin the pressure of the hot and cold water supplies.WeightProduct Gross Weight (Kgs) Total PackagedWeight (Kgs)Rada 215-t3 c 2.360 2.555MaterialsBody: DZR brass nickel plated.Locking Shroud: White engineering plastic.Temperature RangeFactory pre-set maximum outlet temperature: 43°C.Minimum temperature differential, blend to either supply: 12°C.Optimum thermostatic control range: 30 °C - 50 °C.Minimum cold water temperature: 1°C.Maximum hot water temperature: 85 °C.Note! The mixing valve can accept temporary temperature excursionsabove 85°C without damage, however, operation of the mixing valveat such elevated temperatures is not recommended. For reasons ofgeneral safety, hot water storage supply temperatures should ideallybe maintained at between 60°C - 65°C where serving ablutionaryapplications.Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5714


individual/group showeringRada 215-t3 BC thermostatic mixing valve• Approved for use in all UK healthcare premises• Features the unique “Radatherm”service-free cartridge• Unbeatable temperature control• Complete with check valves and strainersSpecify as: Rada 215-t3 bc (1.0.440.02.1)½” thermostatic mixing valve incorporating Radatherm service-freecartridge, check valves and strainers. Housed within swivel elbows,featuring 15 mm compression connectors, which can be converted to½” BSP union if required.Dimensions (mm)Flow Diagram2545014140121Flow Rate - I/min3020106550-70108 15 17000.51.0Pressure Loss – bar1.5 2.0Kohler Mira LimitedCromwell RoadCheltenhamGloucestershireGL52 5EPSpecification EnquiriesTel: 01242 282527Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.com


individual/group showeringTECHNICAL SPECIFICATIONInstallation and MaintenancePlease refer to the appropriate Product Manual.ConnectionsInlet and Outlet: ½” BSP external union or 15 mm compression (nutand olive not provided).Standard connections are hot (left), cold (right), top outlet.ApprovalsBuildcert TMV3 Thermostatic Mixing Valve Scheme approved:LP-S - Low Pressure ShowerHP-S - High Pressure ShowerCertificate No: ETC/14/0597.Complies with the technical requirements of BS7942 for the samedesignations.Designed to comply with European Standards EN1111 and EN1287.WRAS approved (Water Regulations Advisory Scheme).Designed, manufactured and supported in accordance with accreditedBS EN ISO 9001:2000 Quality Management Systems andBS EN ISO 14001:2004 Environmental Management SystemsOperationRada 215-t3 series mixing valves do not have integral flow control;appropriate provision must be made for this in the outlet pipework.This can be in the form of basin/bath tap, stopcock, mechanicaltimed-flow controller or solenoid. The device chosen must be nonconcussivein operation.Pressures/Flow RatesMinimum dynamic supply pressure: 0.15 bar.Maximum dynamic supply pressure: 5 bar.Minimum flow rate:3 l/min at mid blend.Maximum flow rate: 35 l/min at mid blend (which equates to amaximum pressure loss of 1.8 bar).Maximum pressure loss ratio*: 10:1 (in favour of either supply).Maximum static pressure: 10 bar.Note! Both hot and cold pressure should be nominally equal.* Pressure loss ratio is determined by subtracting the resistance toflow of the outlet pipework and outlet fittings (generally known as‘back pressure’, and measured at the outlet of the mixing valve) fromthe dynamic pressures of the hot and cold water at the inlets of themixing valve. This is at its extreme when the mixing valve is beingused at its lowest flow rate and when the maximum inequality occursin the pressure of the hot and cold water supplies.WeightProduct Gross Weight (Kgs) Total PackagedWeight (Kgs)Rada 215-t3 bc 2.870 3.113MaterialsBody: DZR brass nickel plated.Temperature RangeFactory pre-set maximum outlet temperature: 43°C.Minimum temperature differential, blend to either supply: 12°C.Optimum thermostatic control range: 30 °C - 50 °C.Minimum cold water temperature: 1°C.Maximum hot water temperature: 85 °C.Note! The mixing valve can accept temporary temperature excursionsabove 85°C without damage, however, operation of the mixing valveat such elevated temperatures is not recommended. For reasons ofgeneral safety, hot water storage supply temperatures should ideallybe maintained at between 60°C - 65°C where serving ablutionaryapplications.Kohler Mira LimitedCromwell Road, CheltenhamGloucestershire, GL52 5EPSpecification EnquiriesTel: 01242 282527, Fax: 01242 282404Email: rada_technical@mirashowers.comwww.radacontrols.comRada is a registered trademark of Kohler Mira Limited.The company reserves the right to alter product specification without notice.© July 2006 Kohler Mira Limited. All rights reserved.No part of this document, or any accompanying document, may bereproduced or transmitted in any form or by any means, includingphotocopying or electronically, without the permission of Kohler Mira Limited.P5715

More magazines by this user
Similar magazines