Triton T60si - Faucets, Showers, Bathroom, Kitchen, More.

More documents

Recommendations

Info

<strong>T60si</strong>ELECTRICAL REQUIREMENTSRCD(can be part ofconsumer unit)Fuse ormcbWARNINGTHIS APPLIANCE MUST BE EARTHEDThe installation, supply cable and circuitprotection must conform with IEE wiringregulations and be sufficient for theamperage required.The following notes are for guidance only:1 The shower must only be connected to a230-240V ac supply. If you are installing a showerwith a kilowatt rating above 9kW, it is advisableto contact the local electricity supply company.1.1 The electrical rating of the shower is shownon the rating label (fig.2) within the unit.80A or 100Amain switchConsumerunitMetertailsPull cordisolating switchFig.2MeterShowerunitFig.3 schematic of installation circuitIncomingsupplyfuse2 Before making any sort of electricalconnection within the installation, ensure that noterminal is live. If in any doubt, switch off thewhole installation at the consumer unit.3 The shower must be connected to its ownindependent electrical circuit. IT MUST NOT beconnected to a ring main, spur, socket outlet,lighting circuit or cooker circuit.3.1 The electrical supply must be adequate forthe loading of the unit and existing circuits.4 Check your consumer unit (main fuse box)has a main switch rating of 80A or above and thatit has a spare fuse way which will take the fuse ormcb necessary for the shower (fig.3).4.1 If your consumer unit has a rating below80A or if there is no spare fuse way, then theinstallation will not be straight forward and mayrequire a new consumer unit serving the house orjust the shower.4.2 You will need to contact the local electricitycompany. They will check the circuit and carry outwhat is necessary. They will also check the mainbonding.5 The earth continuity conductor of theelectrical installation must be effectivelyconnected electrically to all exposed metal parts ofother appliances and services in the room inwhich the shower is to be installed, to conform tocurrent IEE regulations.Table ACIRCUIT PROTECTIONunitcartridgerating mcb fuse7.0kW 30/32A 30A7.5kW 32A 35A8.0kW 40A 35A8.5kW 40A 45A9.0kW 40A 45A9.5kW 40/45A 45A10.5kW 45A 45A4
<strong>T60si</strong>ELECTRICAL REQUIREMENTS5.1 All exposed metallic parts in the bathroommust be bonded together using a cable of at least4mm 2 cross sectional area. These parts includemetal baths, radiators, water pipes, taps andwaste fittings.6 For close circuit protection DO NOT use arewireable fuse. Instead use a suitably ratedminiature circuit breaker (MCB) or cartridge fuse(see table A).6.1 In the interest of electrical safety a 30mAresidual current device (RCD) should be installedin all UK electric and pumped shower circuits. Thismay be part of the consumer unit or a separateunit.7 A 45 amp double pole isolating switch witha minimum contact gap of 3mm in both polesmust be incorporated in the circuit.7.1 It must have a mechanical indicatorshowing when the switch is in the OFF position,and the wiring must be connected to the switchwithout the use of a plug or socket outlet.7.2 The switch must be accessible and clearlyidentifiable, but out of reach of a person using afixed bath or shower, except for the cord of acord operated switch, and should be placed soTable BTwin and earth PVC insulated cableCURRENT CARRYING CAPACITYclipped direct orinstalled in an in conduit buried in a noninsulated wall or trunking insulated wall6mm 2 6mm 2 6mm 232A 38A 46A10mm 2 10mm 2 10mm 243A 52A 63Athat it is not possible to touch the switch bodywhile standing in a bath or shower cubicle. Itshould be readily accessible to switch off afterusing the shower.8 Where shower cubicles are located in anyrooms other than bathrooms, all socket outlets inthose rooms must be protected by a 30mA RCD.9 The current carrying capacity of the cablemust be at least that of the shower circuitprotection (see table B).9.1 To obtain full advantage of the powerprovided by the shower, use the shortest cableroute possible from the consumer unit to theshower.9.2 It is also necessary to satisfy thedisconnection time and thermal constraints whichmean that for any given combination of currentdemand, voltage drop and cable size, there is amaximum permissible circuit length.10 The shower circuit should be separated fromother circuits by at least twice the diameter of thecable or conduit.10.1 The current rating will be reduced if thecabling is bunched with others, surrounded bythermal loft or wall insulation or placed in areaswhere the ambient temperature is above 30°C.Under these conditions, de-rating factors applyand it is necessary to select a larger cable size.10.2 In the majority of installations, the cablewill unavoidably be placed in one or more ofthe above conditions. This being so, it isstrongly recommended to use a minimum of10mm cabling throughout the showerinstallation.10.3 In any event, it is essential that individualsite conditions are assessed by a competentelectrician in order to determine correct cable sizeand permissible circuit length.16mm 2 16mm 2 16mm 257A 69A 85ANote: Cable selection is dependenton de-rating factors5
Page 1 and 2: . T60si electric shower .Installati
Page 3 and 4: T60siPLEASE READ THIS IMPORTANT SAF
Page 5: T60siKEY TO MAIN COMPONENTS(inside
Page 9 and 10: T60sior shower tray, then a double
Page 11 and 12: T60siA 15mm x 15mm straight coupler
Page 13 and 14: T60siREPLACING THE COVERThe power s
Page 15 and 16: T60siFITTING THE HOSE AND SPRAYHEAD
Page 17 and 18: T60siOPERATING THE SHOWERNOTE: Ensu
Page 19 and 20: T60siOPERATING FUNCTIONSPower indic
Page 21 and 22: T60siSPARE PARTSRef DescriptionPart
Page 23 and 24: T60siTemperature / flow rate graph
Page 25 and 26: T60siFAULT FINDING (continued)Probl
Page 27 and 28: UKASQUALITYMANAGEMENT003

Triton T60si - Faucets, Showers, Bathroom, Kitchen, More.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?