TEMPORARY REVISION - MD Helicopters

More documents

Recommendations

Info

CSP−H−2MD Helicopters, Inc.500 Series − Basic HMITable 2−2. Ground Support Equipment and Special ToolsNOTE: Most of the equipment and tool items in this table are used to support and maintain all configurations of the369H helicopter, except when an asterisk symbol ( * ) is part of the item number to indicate limited use. Limitedapplications noted in the Application or Use column. Special tools used only for major disassembly-repairand/or overhaul of components are listed in applicable section of CSP−H−3. See end of table for explanationof deltas and daggers.ItemPart No. Nomenclature Application or UseNo.1 369A9904−501 Hoisting adapter Hoisting entire helicopter or removing mainrotor.2 369A2010 Jacking fittings Jacking, leveling or tie down of helicopter.3 369D2661 Blade socks Main rotor blade tie downs.4 369H4009 Pitot tube cover Pitot tube protection.5 369H90126 Ground handling wheels(one side)6 369A9905 Ground handling wheel(one side less handle)7 369H9801 Handle−Jack assembly groundhandling (straight)8 369A9906 Handle−Jack assembly, groundhandling (offset)Ground handling of helicopter equipped withutility or emergency floats. (Ref. CSP−H−3)Ground handling of helicopter.Raising and lowering helicopter with groundhandling wheels.Raising and lowering helicopter with groundhanding wheels when addition clearance isrequired.9 369H9925 Collective rigging fixture Rigging of main rotor collective controls(369HE and 369HS only).10 369A9927 Collective rigging fixture Rigging of main rotor collective controls(369HM only).11 369A9930 Mixer rigging plate Rigging of main rotor collective and cycliccontrols.12 369A9929−9 Longitudinal rigging fixture Rigging of main rotor cyclic controls (369HEand 369HS only).13 369A9929−5 Longitudinal rigging fixture Rigging of main rotor cyclic controls (369HMonly).14 369A9928−9 Lateral rigging fixture Rigging of main rotor cyclic controls (369HEand 369HS only).15 369A9928−5 Lateral rigging fixture Rigging of main rotor cyclic controls (369HMonly).16 369A9926−7 or369A9926−5 (1)Main rotor blade tracking high intensitystrobe light installation and assemblyTracking of main rotor blades.17 369A9958 Main rotor blade tab bending tool Adjusting main rotor blade tab angle forblade track.18 369H9928 Main rotor blade tab bending tool Adjusting main rotor blade tab angle forblade track.19 369A9934−601(replaced by 21)Main rotor mast nut wrenchLoosening/Torquing of main rotor mast nut.Page 2−8TR09−001
MD Helicopters, Inc.500 Series − Basic HMICSP−H−2ItemNo.Part No.Table 2−2. Ground Support Equipment and Special Tools (Cont.)NomenclatureApplication or Use20 369A9934 Main rotor mast nut wrench Loosening/Torquing of main rotor mast nut(non−slotted mast only).21 369A9829 Main rotor wrench assembly Loosening/Torquing of main rotor mast nut.22 369A9932 Hub pullerBreaking loose main rotor hub from mast.369A9932 (2)23 369A9949 Torque wrench adapter Checking main rotor damper first stagefriction.24 369A9933 Main rotor hub driverSeating main rotor hub.369A9933−5 (3)25 369A9983 Torque wrench adapter Torque tailboom attachment bolts.26 369A9936 Bungee installation tool Holding collective bungee spring incompression for bungee removal andinstallation.27 369A9985 Bungee spring compression tool rodand channel28 369A9931 or Tail rotor swashplate rigging tool369A9931−3Removing bungee installation tool anddisassembling bungee spring assembly.Rigging of tail rotor controls (fiberglassblades).29 369A9931−5 Tail rotor swashplate rigging tool Rigging of tail rotor controls (metal blades).30 369A9937 Torque wrench adapter Installing tail rotor nut.31 369A9999 (4) Tail rotor balancing kit Strobe light analysis for balancing installedtail rotors.32 FRDH 101 Torque wrench adapter Installing main rotor drive shaft bolts andeyebolts.33 RXT20−5(extraction)RTM20−9(insertion)34 M8ND &N14HTCHYTIP insertion/extraction tool (mfg byBurndy, Norwalk, Connecticut)HYTOOL M8ND (catalog No. Y14MRC); Die−Sets N22PCT−1 & −2, andN14HCT (mfg: same as item No. 33)35 107−0970 Hand−operated crimping tool (CatalogNo. 107−0970) with positioners(Catalog No. 107−0976 and107−0977)(mfg by WinchesterElectronics, Division of LittonIndustries, Main St. and Hillside Ave,Oakville, Connecticut 06779)36 107R1001 and107−1015Removable contact removal tool(Catalog No. 107R1001) and insertiontool (Catalog No. 107−1015) (mfr:same as item No. 25)Installing and removing HYTIP electricalcontacts into and from terminal blockmodules.Manual crimping of MINILOK and MODILOKterminal block contact tips on electrical wireharness leads.Hand crimping of removable contacts inrectangular connectors.NOTE: Tool conforms to MS−3191−2(MIL−T−22520, Class 1).Removing and inserting removable contactsfrom and into inserts of rectangularconnectors.37 Deleted38 369A9948 Engine stand Support for removal or replacement engine.Page 2−9TR09−001
Page 6: CSP−H−2MD Helicopters, Inc.500
Page 9 and 10: MD Helicopters, Inc.500 Series −
Page 16 and 17: CSP−H−2MD Helicopters, Inc.500
Page 28 and 29: CSP−H−2ItemNo.Material11 Paint
Page 30 and 31: CSP−H−2ItemMaterialNo.31 Insula
Page 64 and 65:
CSP−H−2MD Helicopters, Inc.500
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90:
show all

TEMPORARY REVISION - MD Helicopters

Create successful ePaper yourself

Delete template?

Save as template?