7. operating the flexipress - Grass

More documents

Recommendations

Info

7. OPERATING THE FLEXIPRESS Fig. 7-604-01 Fig. 7-604-02 60 XX A1 B1 B2 XX A2 The star in your cabinet
7-604 Drilling Fronts for Grass Zargen Slide Systems 6000/7000 Figs 7-604-01/02 Required equipment: - 2 (1) drill bits dia. 10 mm, left - (1) drill bit dia. 10 mm, right - The numbers in brackets correspond to 32 mm hole spacing Machine set-up: To drill drawer fronts, the vertical gearbox must be swivelled at an angle of 90º. - Turn off the machine at the main switch on the switchgear cabinet. - Lift up the front gearbox cover. - Remove all quick-change chucks incl. drill bits from the gearbox, see section 7-202 - Fit the new quick-change chucks incl. drill bits to the gearbox, see section 7-202 - See Fig. 7-604-01 for spindle configuration - If necessary, set the drilling depth in accordance with the instructions given in section 7-301, using the drilling depth data given in the product specifications. - Set the drilling setup distance, if necessary, in accordance with the instructions given in section 7-302 - Set the Flexipress drilling speed, if necessary, in accordance with the instructions given in section 7-303 - Swivel the vertical drilling head 90° to the right. Pay special attention to section 7-306. Remove all drill bits from the horizontal drilling head (otherwise risk of collision). - Set the side stops in accordance with the instructions given in section 7-501 on the right side only. The distance between the first and second side stop is: 13 mm + bottom width with System 6000 15 mm + bottom width with System 7000 For this purpose there are right side stops with 13 mm or 15 mm wide stop catches. - Turn on the main switch again. The Flexipress is now ready for operation. Operating the Flexipress: 7. OPERATING THE FLEXIPRESS - Place the workpiece on the machine table and press it against the stop pins and the first side stop with one hand - With the other hand, press the vertical drilling head start button until the drilling depth set with knurled screw “6”, Fig. 4-002-03, has been reached. - Place the workpiece on the machine table against the second side stop and press - With the other hand, press the vertical drilling head start button until the drilling depth set with knurled screw “6”, Fig. 4-002-03, has been reached. Caution: While the machine is being operated: keep hands clear of the danger zone around the hold-down devices, the insertion die arm and the gearbox. The safety information given in section 2 is to be followed whenever the machine is being operated. The star in your cabinet 61
Page 1 and 2:
OPERATING INSTRUCTIONS Grass Flexip
Page 3 and 4:
Weights Total weight of Flexipress
Page 5 and 6:
TABLE OF CONTENTS Page 7. Operating
Page 7 and 8:
1-001 List of Figures LIST OF FIGUR
Page 9 and 10: 2-001 Safety Information - It is th
Page 11 and 12: 2-006 Potential Hazards and Suitabl
Page 13 and 14: 3-002 Applications The Flexipress d
Page 15 and 16: 3. DESCRIPTION OF PRODUCTS Side sto
Page 17 and 18: 3. DESCRIPTION OF PRODUCTS Designat
Page 19 and 20: 4. DESCRIPTION OF MACHINE COMPONENT
Page 41 and 42: 6-001 Pneumatic Connection The Flex
Page 43 and 44: 7-1 Requirements for the Operators
Page 45 and 46: 7-301 Setting the Vertical Drilling
Page 47 and 48: 7-303 Setting the Vertical Drilling
Page 49 and 50: 7. OPERATING THE FLEXIPRESS 7-401 S
Page 51 and 52: 7-501 Setting the Side Stops Fig. 7
Page 53 and 54: 7-503 Using the Index Gauge When Dr
Page 55 and 56: 7-601 Drilling and Inserting Grass
Page 57 and 58: 7-602 Drilling and Inserting Grass
Page 59: 7-603 Drilling Lines of Holes Figs
Page 63 and 64: 7-605 Drilling Back Panels for Gras
Page 65 and 66: 7-606 Drilling and Inserting Visibl
Page 67 and 68: 7-607 Bohren und Einpressen von Ver
Page 69 and 70: 7-608 Drilling Holes for Handles Fi
Page 71 and 72: 7-609 Drilling Vertical Holes for D
Page 73 and 74: 7-610 Drilling Holes for Fastening
Page 75 and 76: 7-701 Drilling Horizontal Holes for
Page 77 and 78: 7-702 Drilling Horizontal Holes for
Page 79 and 80: 7-703 Drilling Holes for Joint Supp
Page 81 and 82: 7. OPERATING THE FLEXIPRESS 7-801 D
Page 83 and 84: 8. TROUBLE SHOOTING AND PROBLEM SOL
Page 97 and 98: 10-001 Guarantee Certificate Purcha
Page 99 and 100: 10-002 Disposal Form Purchaser: Nam
Page 101 and 102: 10-003 Resale Form Vendor: Name: .
Page 103 and 104: 10-004 Questionnaire 1 - Reason for
Page 105 and 106: 10-005 Questionnaire 2 - Satisfacti
Page 107 and 108: The star in your cabinet NOTES 107
Page 109 and 110: REPRESENTATIVES AROUND THE WORLD MD
show all

7. operating the flexipress - Grass

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?