Telemecanique Altivar 56 manual - Northern Industrial

More documents

Recommendations

Info

Bulletin No. 50006-519-01BDecember 1996Chapter 6 — Class 8839 ALTIVAR 56 Combination DevicesControl WiringTable 51: Control Terminal Strip Characteristics (Power Circuits Y & Z)Terminal [1] [2] Function Characteristics26 [7]2728 [3]2930 [4]3132 [7]33120 V SPR Relay Coil (if used) 115 - 120 V / 60 Hz supply (user-supplied)R1 Relay, N.C. Contact (Fault RelayOutput)R2 Relay, N.O. Contact (Run RelayOutput)Auxiliary Contact (AFC Mode Status)Minimum: 10 mA, 24 VDCMaximum inductive load of:• 2.0 A, 120 VAC; Max: 0.10 J/operation,80 operations/minute• 1.0 A, 220 VAC; Max: 0.25 J/operation,25 operations/minute• 2.0 A, 24 VAC; Max: 0.10 J/operation,80 operations/minuteArc suppression provided by varistors in parallelw/ relay contacts.Minimum: 10 mA, 24 VDCMaximum inductive load of:• 2.0 A, 120 VAC; Max: 0.10 J/operation,80 operations/minute• 1.0 A, 220 VAC; Max: 0.25 J/operation,25 operations/minute• 2.0 A, 24 VAC; Max: 0.10 J/operation,80 operations/minuteArc suppression provided by varistors in parallelw/ relay contacts.• 15 A, 125 VAC• 10 A, 250 VAC[1] See control circuit diagrams on pages 153 - 156.[2] All terminals are rated 600 V, 30 A (Class 9080, Type GM6). Maximum wire size for all terminals is 10 AWG(2.5 mm 2 ). Tightening torque 7 - 8 lb-in (0.8 - 0.9 N•m).[3] Relay coil deenergizes on fault.[4] Contact state with drive controller deenergized.[5] Total current of +24 V internal supply is 210 mA. Available current of the two logic outputs can be calculated asfollows: each input requires 10 mA, each analog output requires 20 mA and the typical quiescent current ofLOP is 15 mA.[6] 0 - 20 mA, x - 20 mA, 20 - 4 mA programmable with keypad display. 0 - 5 V (Z = 30 kΩ) selectable with switchon control board.[7] Available only when options are included.[8] On when bypass contactor is energized.© 1996 Square D All Rights Reserved137ηττπ://νιχοντρολσ.χοm
Chapter 6 — Class 8839 ALTIVAR 56 Combination DevicesBulletin No. 50006-519-01BOperation Sequence & Options December 1996SEQUENCE OFOPERATION ANDOPTIONSTerminal Command Modevs. Keypad Command ModeThis section describes basic sequences of controller operation for the three preengineeredpower circuit configurations and available options. The options are:• Power Circuit W: combination package• Power Circuit Y: bypass package• Power Circuit Z: remote starter bypass packageIn order for factory and/or user supplied pilot devices and controls to berecognized, the Class 8839 ALTIVAR 56 combination drive controller is factoryconfigured to operate in the Terminal Command mode. Switching from TerminalCommand mode to Keypad Command mode will disable power converter logicinputs. Factory and/or user-provided control devices will be ignored. For thisreason, do not operate the Class 8839 ALTIVAR 56 drive controller in the KeypadCommand mode.Consult the factory configuration listing on the applicable control circuit diagram(pages 151 to 156), and refer to Chapter 5 before reprogramming logic inputs,outputs, torque types, or control types. Changing certain factory settings willadversely affect the performance of the Class 8839 ALTIVAR 56 drive controller.WARNINGUNINTENDED EQUIPMENT OPERATION• Controller has been factory programmed. Alteration of factory programming maycreate incompatibilities with supplied controller configuration.• Read and understand Chapter 5 as well as programming information on applicablecontroller schematics, Figures 91 - 96.• If the power converter unit is re-initialized using the TOTAL or PARTIAL FACTORYSETTING function, the power converter must be re-programmed per theprogramming instructions on applicable controller schematics, Figures 91 - 96.• If the power converter unit or the main control board of the power converter isreplaced, the power converter must be re-programmed per the programminginstructions on applicable controller schematics, Figures 91 - 96.Failure to observe these instructions can result in death, serious injury, orequipment damage.138 © 1996 Square D All Rights Reservedηττπ://νιχοντρολσ.χοm
Page 1 and 2:
Instruction Bulletin50006-519-01BDe
Page 3 and 4:
DANGERHAZARDOUS VOLTAGE• Read and
Page 5:
ALTIVAR 56 Fan and Pump Drive User
Page 8 and 9:
Bulletin No. 50006-519-01BDecember
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
AI2-UAI2-IAI2-UAI2-IAI2-UAI2-IAI2-U
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
AI2-UAI2-IAI2-UAI2-IBulletin No. 50
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Bulletin No. 50006-519-01BChapter 5
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97: Bulletin No. 50006-519-01BChapter 5
Page 124 and 125: Bulletin No. 50006-519-01BDecember
Page 134 and 135: AUTOOFFHAND234510671098AFCOFFBYPASS
Page 136 and 137: HANDOFFAUTO241350678OPENMAINSCLOSEF
Page 140 and 141: L1 L2 L3TelemecaniqueT1 T2 T3L1 L2
Page 142 and 143: 53 NO 61 NC 71 NO 83 NCTelemecaniqu
Page 168 and 169: Bulletin No. 50006-519-01BAppendix
show all

Telemecanique Altivar 56 manual - Northern Industrial

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?