Telemecanique Altivar 56 manual - Northern Industrial

Bulletin No. 50006-519-01BDecember 1996Chapter 2 — WiringControl WiringTable 10: Control Terminal Strip CharacteristicsConnector Terminal [1] Function CharacteristicsR1A [3]R1BJ1 [2] R1CR2AR2BR2CJ12 [2]J13 [2]LI1LI2LI3LI4+24LOPLO1LO2COMSCOMAI1+10AI2AO1AO2COMN.O. contact [4]N.C. contactCommonN.O. contact [4]N.C. contactCommonLogic input 1Logic input 2Logic input 3Logic input 4Control supplyLO supply inputLogic output 1Logic output 2Logic commonFault relayoutputProgrammablerelay outputShield/GroundSpace, for isolationSpeed ref. commonInput 1: Speed ref.voltageReference supplyInput 2: Speed ref. currentAnalog output 1Analog output 2Analog commonMinimum: 10 mA, 24 VDCMaximum: inductive load of:2.0 A, 120 VAC; max: 0.10 J/operation, 80 operations/minute1.0 A, 220 VAC; max: 0.25 J/operation, 25 operations/minute2.0 A, 24 VDC; max: 0.10 J/operation, 80 operations/minuteArc suppression provided by varistors in parallel with relay contacts24 V, 10 mA; State 0: V12 V; Vmax = 30 V24 V, 10 mA; State 0: V12 V; Vmax = 30 V24 V, 10 mA; State 0: V12 V; Vmax = 30 V24 V, 10 mA; State 0: V12 V; Vmax = 30 VIs = 210 mA max. [5]Minimum: 12 V, Maximum: 30 V, quiescent current: typical 15 mA24 V, 200 mA max. [5]24 V, 200 mA max. [5]0 V0 V0-10 V, Z = 30 kΩ10 V, Is = 10 mA max.4-20 mA [6] , Z = 250 Ω0-20 mA, 12 V max. (programmable as 4-20 mA w/ keypad display)0-20 mA, 12 V max. (programmable as 4-20 mA w/ keypad display)0 V[1] See circuit diagrams on page 28 and 29.[2] Max. wire size for all terminals: 14 AWG (2.5 mm 2 ). Tightening torque: 3.5 lb-in (0.4 n•m).[3] Relay coil deenergizes on fault.[4] Contact state with drive controller deenergized.[5] Total current of + 24 V internal supply is 210 mA. Available current of the two logic outputs can be calculated as follows: each logic input requires10 mA, each analog output requires 20 mA and the typical quiescent current of LOP is 15 mA. For example, in an application where three logicinputs and one analog output are used, the total available current is 210 mA - (3 x 10 mA) - (1 x 20 mA) - 15 mA = 145 mA to drive the logic outputloads. If more current is required, an external supply must be used.[6] 0-20 mA, x-20 mA, 20-4 mA programmable with keypad display. 0-5 V (Z = 30 kΩ) selectable with switch on control board.© 1996 Square D All Rights Reserved23ηττπ://νιχοντρολσ.χοm