Telemecanique Altivar 56 manual - Northern Industrial

More documents

Recommendations

Info

Bulletin No. 50006-519-01BDecember 1996Chapter 5 — ConfigurationMenu OverviewMENU OVERVIEWWARNINGUNINTENDED EQUIPMENT ACTION• Unlocking keypad display (page 56) gives access to parameters.• Parameter changes affect drive controller operation. Most parameter changesrequire pressing ENT. Some parameter changes, such as reference frequency,take effect as soon as you press the ▲ or ▼ key.• Read and understand this manual before using the keypad display.Failure to follow these instructions can result in death, serious injury, orequipment damage.Selecting the LanguageDrive ConfigurationDrive IdentificationDisplay ModeWhen drive controller is powered up for the first time, the Language menu appearsallowing you to choose the language used on all menus. Scroll through thelanguage choices with the ▲ and ▼ keys, and make a selection by pressing ENT.Upon subsequent power ups, the display passes directly to the Display screen. Todisplay Language menu after first power up, press the ESC key twice.The Drive Configuration screen shows factory settings of the configurationparameters. Voltage is fixed at 460 V for the 460 V units (ATV56•••N4) and is setto 230 V at first power up for 230 V units (ATV56•••M2). This screen is onlyshown on first power up or after a total return to factory settings. Advance to theDrive Configuration screen from the Language menu by pressing ENT.The Drive Identification screen is automatically displayed on power up, or can beaccessed from the Drive Configuration screen by pressing ENT. The DriveIdentification screen displays the following nameplate information:• ATV56 catalog number• Software version• Motor power• Drive nominal current• I maximum/I nominal• VoltageFrom the Drive Identification screen, press ENT to advance to the Display screen.While the drive controller is running, the default display is a bar graph showingreference frequency and drive status. The type and number of functions displayedcan be modified in the 4→Display Configuration menu (page 62). If the drivecontroller is in fault state, the Display screen shows the fault type. If the drivecontroller has been programmed for Keypad Command, the last line of the Displayscreen indicates the functions of F1, F2, and F3 keys.© 1996 Square D All Rights Reserved53ηττπ://νιχοντρολσ.χοm
Chapter 5 — ConfigurationBulletin No. 50006-519-01BMain Menu December 1996Main MenuFrom the Display screen, press ENT to advance to the Main menu. Depending onthe access level selected (page 56), the Main menu contains two (Total Lock), ornine (Total Unlock) sub-menus.Subsequentpower upFirst power upDIALOGUE/LANGUAGE ?EnglishEspanolFrancais†, & ENTSelect language by scrolling with the ▲ and ▼keys and pressing ENT. Press ENT to advance toDrive Configuration menu.ESCENTor 20 sENTor 10 sDRIVE IDENTIFICATIONATV56U41N4 VT V3.1POWER :2.2kW/3HPIn=5.8A Imax=1.5InSUPPLY :460VENT to continueESCSPEED REFER.47.2 HzACTUAL DRIVE CONFIG.TORQUE: VARIABLECOMMAND: 2 WIREMOT.:60Hz,440-460 VPower: 2.2kW/3 HPENT if OK/F3‘changeENTor 10 sRUNF3Displays factory settings of drivecontroller configuration parameters.Motor power displayed only forATV56U41N4 drive controller. Press ENTto advance to Drive Identification screen.Unlock access locking switch, ifnecessary, for display of the 6→DriveConfiguration menu.Displays drive controller nameplate information:•ATV56U41N4: Drive controller catalog number•VT = Variable torque•V3.1 = Version of drive controller software•2.2 kW / 3 HP = Horsepower•In = Nominal drive controller current•Imax = Maximum drive controller currentPress ENT to advance to Display Mode.When drive controller is running, reference frequency isdisplayed (factory setting). When drive controller is in fault state,fault is displayed. Press ENT to advance to Main menu.ESCMAIN MENUI/O MAPFAULT HISTORYENTContent of Main menu depends on access level selected. Seepage 56.†, & ENT to selectFigure 33: Menus Viewed at First Power Up (Factory Default Screens)54 © 1996 Square D All Rights Reservedηττπ://νιχοντρολσ.χοm
Page 1 and 2:
Instruction Bulletin50006-519-01BDe
Page 3 and 4:
DANGERHAZARDOUS VOLTAGE• Read and
Page 5:
ALTIVAR 56 Fan and Pump Drive User
Page 8 and 9:
Bulletin No. 50006-519-01BDecember
Page 10 and 11:
Page 12 and 13: Bulletin No. 50006-519-01BDecember
Page 28 and 29: AI2-UAI2-IAI2-UAI2-IAI2-UAI2-IAI2-U
Page 52 and 53: AI2-UAI2-IAI2-UAI2-IBulletin No. 50
Page 68 and 69: Bulletin No. 50006-519-01BChapter 5
Page 112 and 113:
Bulletin No. 50006-519-01BChapter 5
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
AUTOOFFHAND234510671098AFCOFFBYPASS
Page 136 and 137:
HANDOFFAUTO241350678OPENMAINSCLOSEF
Page 138 and 139:
Page 140 and 141:
L1 L2 L3TelemecaniqueT1 T2 T3L1 L2
Page 142 and 143:
53 NO 61 NC 71 NO 83 NCTelemecaniqu
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Bulletin No. 50006-519-01BAppendix
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
show all

Telemecanique Altivar 56 manual - Northern Industrial

Create successful ePaper yourself

Delete template?

Save as template?