ASSEMBLY INSTRUCTIONS CELOSIAS

duralmond.de
  • No tags were found...

pre-installation - stoneslikestones.eu

ASSEMBLYINSTRUCTIONSCELOSIASduralmond.de


installation systemgeneral pre-installation guidelinescomponentspre-installationproject equipmentstep by steptechnical drawing34510121335Kreative Ideen für Wand und Decke


installation system3This installation system has been developed to establish a standardmounting system with which we can reduce installation times whilstguaranteeing quality and compliance with the CTE technical building code.Kreative Ideen für Wand und Decke


general pre-installation guidelines4• Pieces must not be unpacked a long time prior to mounting,in order to avoid possible warping.• Before beginning the installation, we must prepare the wall in order toplace the pieces and define the most complcated joins, thus foreseeingall possible circumstances which might affect the installation.Depending on the project roadmap, we could pre-prepare all the specialjoins and the necessary pieces.Kreative Ideen für Wand und Decke


components5Organic 2400x1200mm Classic 2400x1200mm Ogival 2400x1200mmPop 2400x1200mm Ornamental 2400x1200mm Urban 2400x1200mmPanel or lattice size of 2400 x 1200 mm.We can cut lattice pieces to special dimensionsdepending on the needs of your project.Kreative Ideen für Wand und Decke


components6• anchor setPre-installed on the panels, made up of:- 10mm-thick aluminium anchor plate- Nylon plugs, 16mm in diameter and 25mm long.- Phillips flat-headed counter-sunk threaded screws - M5.5x45 - DIN 7982 / ISO 7050Kreative Ideen für Wand und Decke


components7• L plate, - Nomalised aluminium 15x15x3.- Supplied in 6-metre barsKreative Ideen für Wand und Decke


components8• alignment paddingguideand alignment system 30mm in diameter x 3mm thickKreative Ideen für Wand und Decke


components9• HILTI anchor system- variable length threaded rod on order- fixing nuts and washers- chemical soldering in drilled hole- plugKreative Ideen für Wand und Decke


pre-installation10All of the lattices will have, on their reverse side, a set of anchorsinstalled in the factory.We can increase, vary or change the position of these anchors duringthe project if necessary. This is why the anchor plates need to be fixed topanels as indicated in the diagrams.Kreative Ideen für Wand und Decke


pre-installation11The anchor plates must be spread over the upper area ofthe lattice and on one of its sides, according to how it will beplaced during the project.For special areas, like end pieces at +90º, these adjustmente willbe carried out during the project, or perhaps during apre-installation study.Kreative Ideen für Wand und Decke


project equipment12During the project execution phase, the workmen must have the following equipmentavailable to correctly carry out the installation.Silicone gunTape measure Level Screwdriver Circular sander WrenchesDrill Dril bits MD 2000 Applicator HIT-DL K Cleaning sheathKreative Ideen für Wand und Decke


step by step14Drill Drill bits Circular sanderPut the aluminium L plate in place; this will be used tocorrectly align the wall covering.Kreative Ideen für Wand und Decke


step by step13Tape measureLevelFirstly, we establish a previously fenced-off mounting areaaround the whole perimeter to be covered.Kreative Ideen für Wand und Decke


step by step15ScrewdriverFix the L plate to the floor by drilling holes for screws.Spread the fixings over the length of the plate.Kreative Ideen für Wand und Decke


step by step17Tape measure Level ScrewdriverLattice with pre-mounted anchor plates.We can place the anchor plates at different distances,depending on the model used and their place in the project.Kreative Ideen für Wand und Decke


step by step19HIT-DL K Cleaning sheathPut the wall plug in the previously drilled and cleaned holes.Warning!You only need to use the plug if the structure is not uniform or hollow.If you’re working with concrete, you don’t need to install the plug.En primer lugar, estableceremos una distancia de montaje,previamente acotada, en todo el perimetro a revestir.Kreative Ideen für Wand und Decke


step by step18DrillDrill bitsDrill the holes needed to take the lattice, at the previously marked-out fixing points.The hole drilled must be 10mm in diameter and 40mm deep.Warning!The diameter and depth of the holes drilled must be the same across the whole installation.Kreative Ideen für Wand und Decke


step by step20MD 2000 ApplicatorInject the chemical solution into each drilled hole.En primer lugar, estableceremos una distancia de montaje,previamente acotada, en todo el perimetro a revestir.Kreative Ideen für Wand und Decke


step by step21Place the threaded rod set in the hole, torque / counter-torque,with the mesh and chemical solution.En primer lugar, estableceremos una distancia de montaje,previamente acotada, en todo el perimetro a revestir.Kreative Ideen für Wand und Decke


step by step2230-40 min.Let the chemical solution react and create a solder between thethreaded rod, the chemical solution and the drilled hole.Kreative Ideen für Wand und Decke


step by step23Repeat this step with each of the drilled holes.Kreative Ideen für Wand und Decke


step by step24Place the first lattice in front of the threaded rods and lower L plate.Kreative Ideen für Wand und Decke


step by step25Anchor the lattice between using torque andcoutner-torque in all of the anchor points.Kreative Ideen für Wand und Decke


step by step26WrenchesUse the torque/counter-torque systemto fix the lattice to the threaded rod.Kreative Ideen für Wand und Decke


step by step27Tape measure level WrenchesRepeat this step for each adjoining panel.Check they all line up correctly.Kreative Ideen für Wand und Decke


step by step28Silicone gunPlace the alignment padding between the panels onthe upper surface of the lattice, applying a layer ofstructural silicone..Kreative Ideen für Wand und Decke


step by step29Tape measure Level Drill Drill bitsMark out and drill the holes for the upper lattice,takinginto account the distance between and number of ancpoints pre-mounted on the lattice.horKreative Ideen für Wand und Decke


step by step30Tape measure Level WrenchesRepeat this step using the torque/counter-torque system andthe alignment padding between the walls.Install each of the upper panels one after the other.Kreative Ideen für Wand und Decke


step by step31Tape measure Level WrenchesCheck the correct placement of the lattices you have installed.Kreative Ideen für Wand und Decke


step by step32Tape measure-90ºJoins at +90º or -90º+90ºKreative Ideen für Wand und Decke


step by step33Circular sander Measure Level Wrenches+90ºCut the lattice to the right size and keep at leastthree anchor points to be able to install the panel.Bear in mind that you need a minimum anchordistance of 60mm between the edge of the walland the anchor.Kreative Ideen für Wand und Decke


step by step34Tape measure Level Wrenches-90ºThe join between two lattices at -90º,must be made like a beginning and end panel piecein order to properly install them.Kreative Ideen für Wand und Decke


technical drawing 35Kreative Ideen für Wand und Decke


© 2013 Stones like Stones GmbH ® Irrtümer und Druckfehler vorbehalten. Helligkeit und Farbdarstellung sind unverbindlich, da vom verwendeten Monitor abhängig.Kopie und Vervielfältigung in jeder Form nur mit schriftlicher Genehmigung. · Design+Kommunikation Schneider ms@tatsache.deduralmond.deMSD-Generalvertretung · D-45279 Essen · Ruhrau 41 · Tel: +49 (0)01 52 36 77 0 · Fax: +49 (0)201 52 36 77 19 · e-mail: info@stoneslikestones.de

More magazines by this user
Similar magazines