Proto - Douilles à choc

IMPACT

SOCKETS

Table of Contents

1/4" Drive impact

sets 464-467

Open Stock 507-509

3/8" & 1/2" Drive impact Socket set 468-469

3/8" Drive impact

sets 470-481

Open Stock 510-517

1/2" Drive impact

sets 482-496

Open Stock 518-527

3/4" Drive impact

Sets 497-501

Open Stock 528-535

1" Drive impact

Sets 502-506

Open Stock 536-543

1-1/2" Drive impact Sockets 544-549

2-1/2" Drive impact Sockets 550-551

#5 Spline Drive impact Sockets 551-552

magnetic impact Sockets 553-554

power Sockets 555-556

TorquePlus

for Impact

Sockets

TorquePlus is a fresh look at an old problem in sockets: worn, stripped,

and stubborn nuts and bolts. Conventional sockets contact the fasteners near

the points of both the fastener and the socket, where they are the weakest.

Excessive force on this combination of fastener and socket can cause fastener

rounding or cut through the socket wall.

The TorquePlus design enables sockets to grip

the fastener flats, away from the points. Allows

up to 15% more torque to be applied safely

to the fastener. Reduces the risk of

fastener rounding. Improves the ability

to turn worn or rounded fasteners.

Rounded Corners.

Nearly All Sizes.

Every Proto ® socket,

except the smallest

or largest, have the

TorquePlus feature.

Blue indicates Stress Point.

Point of Contact.

462

Stress point has moved away from the

tip. Wall of the socket meets with the

flat of the fastener for a much wider

area of contact.

Impact Socket Safety

BEFORE

This is your sign of safety.

Straight Pin with Smooth Sides.

AFTER

Bent Pin with Notched Sides.

Retaining Safety

Properly used, retaining rings hold sockets firmly in place on

drive anvils.

> > Always use retaining rings with pneumatic drive anvils and sockets.

> > Install rings correctly to ensure all rotational force stays between the anvil

and socket as rings are only intended to support the weight of the socket.

> > Consider using crush gauge rings for added safety.

> > Be sure to inspect both drive anvil and socket carefully before using.

How the Crush Gauge

improves safety

Cracked or worn sockets pose a safety hazard. Our Crush

Gauge Ring can indicate wear before there’s a catastrophic

failure. When a socket is cracked or excessively worn or when

an anvil is worn, the drive tool and socket don't rotate tightly

together. That action crimps the pin or “crush gauge” on the

retaining ring. If that happens, you know to inspect and replace

the socket or drive anvil.

Retaining Rings

When used correctly, retaining rings improve both the safety and performance of pneumatic impact drivers.

Proto ® offers three styles.

One-Piece Rings eliminate having to handle

two small parts. They work in much the same

way, but the pin is integrated into the ring and

installs quickly.

Crush Gauge Rings work like one-piece rings, but

they are specially designed to indicate damage or

wear on sockets and drive anvils. Fast and reliable,

they add an element of safety to your work.

Traditional Rings are made in two pieces that

include a steel pin and O-ring. To install, slip the

pin through the socket and drive anvil and slip the

O-ring into the socket groove.

463

1/4" Drive 13 piece Impact Socket Set - 6 Point

Product #: J69206

6

1/4" Drive impact Socket sets

Contents

Description

J6904M Socket, Impact 1/4" DR 4 mm 6 PT


J69055M Socket, Impact 1/4" DR 5.5 mm 6 PT











J2588 Socket Bar, 11"

J2590

Socket Clip, 1/4" DR

Weight (lbs): 0.88

7 ASME B107.33M

MM

1/4" Drive 11 Piece Impact Socket Set - 6 Point

Product #: J69106

6

Contents

Description

J6906H

Socket, Impact 1/4" DR 3/16" 6 PT

J6907H


J6908H


J6909H


J6910H


J6911H


J6912H


J6914H


J6916H


J6918H


J6920H



J2590


Weight (lbs): 0.66 7 ASME B107.2

INCH

464 Country of origin accurate at time of printing, consult www.protoindustrial.com for updated information.

Impact Socket Sets

1/4" Drive 11 Piece Deep Impact

Socket Set - 6 Point

1/4" Drive 11 Piece Metric Deep

Impact Socket Set - 6 Point

Product #: J69116

6

INCH

Product #: J69212

6

MM


Contents

Description

J6506H

Socket, Impact Deep 1/4" DR 3/16" 6 PT

J6507H


J6508H


J6509H


J6510H


J6511H


J6512H


J6514H


J6516H


J6518H


J6520H



J2590



Contents

Description

J6505MH Socket, Impact Deep 1/4" DR 5 mm 6 PT












J2590


Weight (lbs): 1.36

7 ASME B107.33M

4 4 POINT 6 6 POINT 8 8 POINT 12 12 POINT SPL SPLINE TORX ®

Torx ® hex HEX

BLACK OXIDE

WARNING: WORK SAFELY WITH TOOLS. WEAR SAFETY GOGGLES. +1.800.800.TOOL · Fax: +1.770.648.9108 · www.protoindustrial.com 465


1/4" Drive 7 piece Impact


Product #: J69202

Contents

Description

J6907M

Socket, Impact 1/4" DR 7 mm 6 PT

J6908M


J6909M


J6910M


J6911M


J6912M


J6913M


J2590


Weight (lbs): 0.40

7 ASME B107.33M

6

MM



Product #: J69102

Contents

Description

J6908H


J6910H


J6912H


J6914H


J6916H


J6918H


J2584 Socket Bar, 6-1/4"

J2590



6

INCH

1/4" Drive 9 Piece Metric Universal


Product #: J62133M

12

> > The TorquePlus features apply.

MM

> > Stamped size for easy reference.

> > Side locking hole.

> > Radius-corner socket design

> > Engages flats for better grip

> > Extends fastener life

> > Turns worn fastners easily

Contents

Description

J66555MP Socket, Impact Universal 1/4" DR 5.5 mm 12 PT

J66506MP Socket, Impact Universal 1/4" DR 6 mm 12 PT








J2590



Weight (lbs): 2.20 7

Torx ® is a trademark of Acument Intellectual Properties, LLC


1/4" Drive 7 Piece Torx ® Impact Socket Set

Product #: J69132

TORX ®

Impact Socket Sets

Contents

Description

J6904TX

Socket, Impact 1/4" DR Torx ® E4

J6905TX


J6906TX


J6907TX


J6908TX


J6910TX


J6912TX



J2590




1/4" & 3/8" Drive 10 Piece Torx ® Impact Socket Set

Product #: J39230

TORX ®

Contents

J6904TX

J6905TX

J6906TX

J6907TX

J6908TX

J7208TX

J7210TX

J7212TX

J7214TX

J7216TX

Description


J2590

J2591













J5299R Set Box, 10-3/8"



Torx ® hex HEX

BLACK OXIDE


3/8 & 1/2" DRIVE 86 Piece Impact Socket Set - 6 Point

Product #: J7274

3/8" & 1/2" Drive impact Socket set

INCH

6

MM


Impact Socket Sets

Contents

J7210H

J7212H

J7214H

J7216H

J7218H

J7220H

J7222H

J7224H

J7710H

J7712H

J7714H

J7716H

J7718H

J7720H

J7722H

J7724H

J7209M

J7210M

J7211M

J7213M

J7214M

J7215M

J7217M

J7219M

J7009M

J7010M

J7011M

J7013M

J7014M

J7015M

J7017M

J7019M

J7414H

J7416H

J7418H

J7420H

J7422H

J7424H

J7426H

J7428H

J7430H

J7432H

J7434H

J7436H

J7440H

Description

























Socket, Impact Deep 3/8" DR 9 mm 6 PT

















Socket, Impact 1/2" DR 1" 6 PT

Socket, Impact 1/2" DR 1-1/16" 6 PT



Contents

Description

J7314H


J7316H


J7318H


J7320H


J7322H


J7324H


J7326H


J7328H


J7330H


J7332H

Socket, Impact Deep 1/2" DR 1" 6 PT

J7334H

Socket, Impact Deep 1/2" DR 1-1/16" 6 PT

J7336H


J7340H


J7410M


J7411M


J7412M


J7413M


J7414M


J7415M


J7416M


J7417M


J7418M


J7419M


J7421M


J7422M


J7426M


J7427M


J7310M


J7311M


J7312M


J7313M


J7314M


J7315M


J7316M


J7317M


J7318M


J7319M


J7321M


J7322M


J7326M


J7327M



3/8" & 1/2" Drive impact Socket set


Torx ® hex HEX

BLACK OXIDE


3/8" Drive 25 Piece Impact





Product #: J72125

6

INCH

Product #: J72118

INCH

6

MM

Contents

Description

J7208H

Socket, Impact 3/8" DR 1/4" 6PT

J7210H


J7212H


J7214H


J7216H


J7218H


J7220H


J7222H


J7224H


J7226H


J7228H


J7230H


J7232H

Socket, Impact 3/8" DR 1" 6PT

J7210H

Socket, Impact Deep 3/8" DR 5/16" 6PT

J7212H


J7214H


J7216H


J7218H


J7220H


J7222H


J7224H


J7226H


J7228H


J7230H


J7232H

Socket, Impact Deep 3/8" DR 1" 6PT

J2591




Contents

Description

J7710H


J7712H


J7714H


J7716H


J7718H


J7720H


J7722H


J7724H


J7726H


J7728H


J7730H


J7732H


J7007M


J7008M


J7009M


J7010M


J7011M


J7012M


J7013M


J7014M


J7015M


J7016M


J7017M


J7018M


J7019M



J2591




Impact Socket Sets





Product #: J72220

INCH

6

MM

Product #: J72230

INCH

6

MM


Contents

Description

J7208H


J7210H


J7212H


J7214H


J7216H


J7218H


J7220H


J7222H


J7224H


J7207M


J7208M


J7209M


J7210M


J7211M


J7212M


J7213M


J7214M


J7215M


J7216M


J7217M



J2591



Contents

Description

J7208H


J7210H


J7212H


J7214H


J7216H


J7218H


J7220H


J7222H


J7224H


J7210M


J7211M


J7212M


J7213M


J7214M


J7215M


J7217M


J7218M


J7219M



J2591




Torx ® hex HEX

BLACK OXIDE


3/8" Drive 19 Piece Metric





Product #: J72206

6

MM

Product #: J72216

6

MM

Contents

Description

J7206M


J7207M


J7208M


J7209M


J7210M


J7211M


J7212M


J7213M


J7214M


J7215M


J7216M


J7217M


J7218M


J7219M


J7220M


J7221M


J7222M


J7223M


J7224M



J2591



Contents

Description

J7006M


J7007M


J7008M


J7009M


J7010M


J7011M


J7012M


J7013M


J7014M


J7015M


J7016M


J7017M


J7018M


J7019M


J7020M


J7021M


J7022M


J7023M


J7024M



J2591




Impact Socket Sets





Product #: J72106

6

INCH

Product #: J72116

6

INCH


Contents

Description

J7208H


J7209H


J7210H


J7211H


J7212H


J7214H


J7216H


J7218H


J7220H


J7222H


J7224H


J7226H


J7228H


J7230H


J7232H



J2591



Contents

Description

J7708H


J7709H


J7710H


J7711H


J7712H


J7714H


J7716H


J7718H


J7720H


J7722H


J7724H


J7726H


J7728H


J7730H


J7732H



J2591




Torx ® hex HEX

BLACK OXIDE



3/8" Drive 11 Piece Metric Impact


Product #: J72202

6

MM



Product #: J72212

6

MM

Contents

Description

J7207M


J7208M


J7209M


J7210M


J7211M


J7212M


J7213M


J7214M


J7215M


J7216M


J7217M



J2591



Contents

Description

J7007M


J7008M


J7009M


J7010M


J7011M


J7012M


J7013M


J7014M


J7015M


J7016M


J7017M



J2591




Impact Socket Sets



Product #: J72102

6

INCH



Product #: J72112

6

INCH


Contents

Description

J7208H


J7210H


J7212H


J7214H


J7216H


J7218H


J7220H


J7222H


J7224H



J2591



Contents

Description

J7708H


J7710H


J7712H


J7714H


J7716H


J7718H


J7720H


J7722H


J7724H



J2591




Torx ® hex HEX

BLACK OXIDE



Product #: J76119

12


INCH

Contents

Description

J10012T

Socket, Impact 1" DR 3/4" 12PT

J10014T


J10015T


J10016T

Socket, Impact 1" DR 1" 12PT

J10017T

Socket, Impact 1" DR 1-1/16" 12PT

J10018T


J10020T


J10021T


J10022T


J10023T


J10024T


J10026T


J10027T


J10028T


J10030T


J10032T

Socket, Impact 1" DR 2" 12PT

J10033T


J10036T


J10038T


Weight (lbs): 7

3/8" Drive 12 Piece Metric Thin Wall

Deep Impact Socket Set - 6 Point

Product #: J72217

6

> > Specifically designed for tight clearance applications.

>

MM

> Reduced wall thickness helps improve access to fasteners

in restricted areas.

> > All impact sockets feature one through hole and a groove to accept a

retaining ring and pin to secure the socket to the power tool anvil.

> > Chamfered service ends for quick and positive fastener engagement.

Contents Description

J7008MHT Socket, Impact Thin Wall Deep 3/8" DR 8 mm 6 PT













> > Thin wall sockets are lightweight.

>

> Thinner walls help improve productivity by making it easier to gain

access to fasteners in confined spaces.

> > Extra deep length helps improve access in confined areas.

> > Often used in application where fasteners are close together,

such as tire service.



Impact Socket Sets

3/8" Drive 9 Piece Thin Wall Deep Impact Socket Set - 6 Point

Product #: J72117

Contents

Description

J7708HT Socket, Impact Thin Wall Deep 3/8" DR 1/4" 6 PT










3/8" Drive 7 piece Torx ® Impact Socket Set

Product #: J72132

> > Proto ® Torx ® Impact Sockets can be used on stubborn Torx ® fasteners.

> > Tight tolerances for snug fit on fastener.

>

> Torx ® impact sockets are used wherever powered drive tools are used to

install or remove fasteners.

> > Torx ® impact sockets are designed to withstand the high torque and

force associated with impact tools in repetitive application.

6

INCH

TORX ®


Contents

Description

J7206TX


J7207TX


J7208TX


J7210TX


J7212TX


J7214TX


J7216TX



J2591



3/8" Drive 10 Piece Metric Universal Impact Socket Set - 6 Point

Product #: J72133M

Contents

Description

6

MM












J2591




Torx ® hex HEX

BLACK OXIDE



3/8" Drive 10 Piece Deep Metric Universal


Product #: J72135M

6

Contents

J78410MP

J78411MP

J78412MP

J78413MP

J78414MP

J78415MP

J78416MP

J78417MP

J78418MP

J78419MP

Description


Socket, Impact Universal Deep 3/8" DR 10 mm 6 PT










J2591



MM

3/8" Drive 10 Piece Metric Universal Impact Socket Set - 12 Point

Product #: J72137M

Contents

Description


12

MM











J2591



3/8" Drive 7 Piece Universal Impact Socket Set - 6 Point

Product #: J72144

6

> > Ball and spring design which allows for a 30° working angle.

> > Smooth 360° rotation.

INCH

Contents Description

J77273P Socket, Impact Universal 3/8" DR 3/8" 6 PT





J77278P Socket, Impact Universal 3/8" DR 11/16"

J77279P Socket, Impact Universal 3/8" DR 3/4"


J2591




Impact Socket Sets


Product #: J72142

Contents

Description

J77273P

Socket, Impact Universal 3/8" DR 3/8" 6 PT

J77274P


J77275P


J77276P


J77277P


J2591



6

INCH

3/8" Drive Hex Bit impact sets

3/8" & 1/2" Drive 10 Piece Hex Bit Impact Socket Set

Product #: J72156

> > Drive end chamfer and four detents help provide quick positive

engagement with drive tool on any of the socket drive walls.

>

> Large clearance holes, concentric opening and nut end chamfer make it

easy to position socket on fasteners.

> > Made from high strength steel to help minimize wall thickness

and provide access to fasteners in recesses and where nuts

and bolts protrude.

> > Proto ® Hex Bit Impact Sockets can be used on stubborn fasteners.


>

> Hex bit impact sockets are used wherever powered drive tools are used

to install or remove fasteners.

> > Hex bit impact sockets are designed to withstand the high torque and



hex

INCH

Contents

Description

0.1633 in Socket, Impact Hex Bit 3/8" DR 1/8"

J72905/32 Socket, Impact Hex Bit 3/8" DR 5/32"









J4968PB

Case, Blow Molded Red



Torx ® hex HEX

BLACK OXIDE


3/8" Drive 7 Piece Hex Bit Impact Socket Set

Product #: J72152

hex

3/8" Drive hex Bit impact sets

INCH

Contents

Description









J2591



3/8" Drive 5 Piece Metric Hex Bit Impact Socket Set

Product #: J72252

hex

MM

Contents

Description

J7290-4M

Socket, Impact Hex Bit 3/8" DR 4 mm

J7290-5M


J7290-6M


J7290-8M


J7290-10M Socket, Impact Hex Bit 3/8" DR 10 mm


J2591




3/8" Drive 13 Piece Hand Impact Driver Set

Product #: J7099A

hex

Impact Socket Sets

> > Designed to loosen hard to turn bolts and nuts.

>

>

> Hand impact driver has heavy-duty spring for added torque.

> Popular interchangeable bits are packaged in plastic blow-molded case

for easy storage.

Contents

Description

J7099 Driver, Hand Impact 3/8" DR 5-1/2"

J60002

Bit, Insert # 1 Phillips 1/4" Hex

J60008


J60020


J60202

Bit, Insert 3/16" Slotted 1/4" Hex

J60208

Bit, Insert 9/32" Slotted 1/4" Hex

J60050

Bit, Insert #1 Phillips 5/16" Hex

J60052


J60054


J60256

Bit, Insert 10F-12R Slot 5/16" Hex

J60262

Bit, Insert 14F-16R Slot 5/16" Hex

J6930

Bit Holder 3/8" DR 5/16" Hex

J6931

Bit Holder 3/8" DR 1/4" Hex


3/8" Drive impact Driver set & extensions

3/8" Drive 3 Piece Impact Extension SET

Product #: J7277A

> > Solid one-piece design helps prevent the locking components from becoming

loose or disengaged.

> > Patented locking feature locks sockets to the extension with exceptional force.

> > Knurled shank provides a slip-resistant grip when hand-turning the extension.

Contents

Description

J7175P Extension, Impact 3/8" DR 3"




3/8" Drive 3 Piece Impact Locking Extension Set

Product #: J7277L



>


> Patented locking feature locks sockets to the extension with exceptional force.

Contents

Description

J7203L Extension, Impact Locking 3/8" DR 3"





Torx ® hex HEX

BLACK OXIDE


1/2" Drive 30 Piece Deep Fractional &

Standard Metric Impact Socket Set - 6 Point


Product #: J54215

6

INCH MM

Contents

J7312H

J7314H

J7316H

J7318H

J7320H

J7322H

J7324H

J7326H

J7328H

J7330H

J7332H

J7334H

J7336H

J7338H

J7340H

J7410M

J7411M

Description


















Contents

Description

J7412M


J7413M


J7414M


J7415M


J7416M


J7417M


J7418M


J7419M


J7420M


J7421M


J7422M


J7423M


J7424M




J2592




Impact Socket Sets

1/2" Drive 30 Piece Deep & Standard

Metric Impact Socket Set - 6 Point

Product #: J74306

6

MM

1/2" Drive impact Socket Sets

Contents

J7408M

J7409M

J7410M

J7411M

J7412M

J7413M

J7414M

J7415M

J7416M

J7417M

J7418M

J7419M

J7420M

J7421M

J7422M

J7424M

Description

















Contents

Description

J7310M


J7311M


J7312M


J7313M


J7314M


J7315M


J7316M


J7317M


J7318M


J7319M


J7320M


J7321M


J7322M


J7324M




Torx ® hex HEX

BLACK OXIDE


1/2" Drive 25 piece Metric


1/2" Drive 25 piece Metric Deep



Product #: J74206

6

MM

Product #: J74216

6

MM

Contents

Description

J7408M


J7409M


J7410M


J7411M


J7412M


J7413M


J7414M


J7415M


J7416M


J7417M


J7418M


J7419M


J7420M


J7421M


J7422M


J7423M


J7424M


J7425M


J7426M


J7427M


J7428M


J7429M


J7430M


J7432M


J7436M



J2592



Contents

Description

J7308M


J7309M


J7310M


J7311M


J7312M


J7313M


J7314M


J7315M


J7316M


J7317M


J7318M


J7319M


J7320M


J7321M


J7322M


J7323M


J7324M


J7325M


J7326M


J7327M


J7328M


J7329M


J7330M


J7332M


J7336M



J2592




Impact Socket Sets



1/2" Drive 19 piece Deep Impact


Product #: J74106

6

INCH

Product #: J74116

6

INCH


Contents

Description

J7412H


J7414H


J7416H


J7418H


J7420H


J7422H


J7424H


J7426H


J7428H


J7430H


J7432H


J7434H


J7436H


J7438H


J7440H


J7442H


J7444H


J7446H


J7448H




J2592



Contents

Description

J7312H


J7314H


J7316H


J7318H


J7320H


J7322H


J7324H


J7326H


J7328H


J7330H


J7332H


J7334H


J7336H


J7338H


J7340H


J7342H


J7344H


J7346H


J7348H




J2592




Torx ® hex HEX

BLACK OXIDE



1/2" Drive 18 piece Metric deep




Product #: J72149M

6

Product #: J74104

6

MM

INCH

Contents

Description

J7310M


J7311M


J7312M


J7313M


J7314M


J7315M


J7316M


J7317M


J7318M


J7319M


J7320M


J7321M


J7322M


J7323M


J7324M


J7325M


J7326M


J7327M




J2592



Contents

Description

J7412H


J7414H


J7416H


J7418H


J7420H


J7422H


J7424H


J7426H


J7428H


J7430H


J7432H


J7434H


J7436H


J7438H


J7440H



J2592




Impact Socket Sets

1/2" Drive 15 piece Deep


1/2" Drive 15 piece Metric


Product #: J74114

6

INCH

Product #: J74204

6

MM


Contents

Description

J7312H


J7314H


J7316H


J7318H


J7320H


J7322H


J7324H


J7326H


J7328H


J7330H


J7332H


J7334H


J7336H


J7338H


J7340H




J2592



Contents

Description

J7410M


J7411M


J7412M


J7413M


J7414M


J7415M


J7416M


J7417M


J7418M


J7419M


J7420M


J7421M


J7422M


J7423M


J7424M



J2592




Torx ® hex HEX

BLACK OXIDE





Product #: J74214

6

MM



Product #: J74242

INCH

6

MM

Contents

Description

J7310M


J7311M


J7312M


J7313M


J7314M


J7315M


J7316M


J7317M


J7318M


J7319M


J7320M


J7321M


J7322M


J7323M


J7324M



J2592



Contents

Description

J7412H


J7414H


J7416H


J7418H


J7420H


J7424H


J7408M


J7410M


J7412M


J7414M


J7417M


J7419M



J2592




Impact Socket Sets

1/2" Drive 11 piece Impact Socket

Set - 6 Point

Product #: J74102

6

INCH



Product #: J74112

6

INCH


Contents

Description

J7416H


J7418H


J7420H


J7422H


J7424H


J7426H


J7428H


J7430H


J7432H


J7434H


J7436H



J2592



Contents

Description

J7316H


J7318H


J7320H


J7322H


J7324H


J7326H


J7328H


J7330H


J7332H


J7334H


J7336H



J2592




Torx ® hex HEX

BLACK OXIDE





Product #: J74201

INCH

6

MM



Product #: J74212

6

MM

Contents

Description

J7316H


J7318H


J7320H


J7324H


J7326H


J7313M


J7316M


J7317M


J7319M


J7321M



Contents

Description

J7310M


J7311M


J7312M


J7313M


J7314M


J7315M


J7316M


J7317M


J7318M


J7319M



J2592




Impact Socket Sets

1/2" Drive 10 piece METRIC


1/2" Drive 8 piece deep Impact


Product #: J74202

6

MM

Product #: J72159

6

INCH


Contents

Description

J7410M


J7411M


J7412M


J7413M


J7414M


J7415M


J7416M


J7417M


J7418M


J7419M



J2592



Contents

Description

J7316H


J7318H


J7320H


J7322H


J7324H


J7326H


J7328H


J7330H



J2592




Torx ® hex HEX

BLACK OXIDE



1/2" Drive 7 piece Impact Socket

Set - 6 Point

Product #: J72157

6

INCH

1/2" Drive 5 piece METRIC DEEP


Product #: J74218

6

MM

Contents

Description

J7414H


J7416H


J7418H


J7420H


J7422H


J7424H


J7426H



J2592



Contents

Description

J7317M


J7319M


J7321M


J7322M


J7324M




Impact Socket Sets


Thin Wall Socket Set - 6 Point

Product #: J74117

> > Specifically designed for light clearance applications.

>

INCH

> Reduced wall thickness helps improve access to fasteners in

restricted areas.

> > All Impact sockets feature one through hole and a groove to accept

a retaining ring and pin to secure the socket to the power tool anvil.

Chamfered service ends for quick and positive fastener engagement.


> > Designed to fit into smaller spaces.

>

> Thinner walls help improve productivity by making it easier to gain


> > Often used in application where fasteners are close together, such as

tire service.


6

1/2" Drive 15 Piece Metric

Deep Impact Thin Wall


Product #: J74217

6

MM


Contents

Description











J7332HT Socket, Impact Thin Wall Deep 1/2" DR 1" 6 PT

J7334HT

J7336HT

J7338HT

J7340HT

Socket, Impact Thin Wall Deep 1/2" DR 1-1/16" 6 PT





Contents

Description

















J2592


Weight (lbs): 7.51

7 ASME B107.33M


Torx ® hex HEX

BLACK OXIDE




Product #: J74143



Contents

Description

J74275P


J74276P


J74277P


J74278P


J74279P


J74280P


J74281P


J74282P


J74283P

Socket, Impact Universal 1/2" DR 1" 6 PT

J74284P

Socket, Impact Universal 1/2" DR 1-1/16" 6 PT

J74285P


J74286P


J74287P



6

INCH


Product #: J74142

Contents

Description

J74274P


J74275P


J74276P


J74277P


J74278P


J74279P


J74280P



J2592



6

INCH

1/2" Drive 7 Piece Universal Metric Impact Socket Set - 6 Point

Product #: J72143M

Contents

J74413MP

J74414MP

J74415MP

J74416MP

J74417MP

J74418MP

J74419MP

J2592

Description

Socket, Impact Universal 1/2" DR 13 mm 6 PT










6

MM


Impact Socket Sets

1/2" Drive 8 Piece Deep Universal Impact Socket Set - 6 Point

Product #: J72145

Contents

Description

J75275P

Socket, Impact Universal Deep 1/2" DR 1/2" 6 PT

J75276P


J75277P


J75278P


J75279P


J75280P


J75281P


J75282P


J2592




6

INCH


1/2" Drive 7 Piece Deep Universal

metric Impact Socket Set - 6 Point

Product #: J72147M

Contents

Description

J75413MP Socket, Impact Universal Deep 1/2" DR 13 mm 6 PT







J2592




6

MM

1/2" Drive 7 Piece Hex Bit Impact Socket Set

Product #: J74152

hex

Contents

Description









J2592



INCH


Torx ® hex HEX

BLACK OXIDE


1/2" Drive impact Hex Bit sets & Extensions

1/2" Drive 6 Piece Metric Hex Bit Impact Socket Set

Product #: J74252

> > Made of forged steel.

>


> Size stamped on tool for easy identification.

Contents

Description

J7441-6M


J7441-8M







J2592



1/2" Drive 3 Piece Locking Impact Extension Set

Product #: J7515



>



hex

MM

Contents

Description

J7503 Extension, Impact, Locking 1/2" DR x 3"




1/2" Drive 4 Piece Impact Extension Set

Product #: J7515A



>



Contents

Description



J7182P Extension, Impact 1/2" DR 2-11/16"

J7183-00 Extension, Impact 1/2" DR 10"



Impact Socket Sets

3/4" Drive 21 Piece Metric Impact Socket Set - 6 Point

Product #: J72103M

6

Contents

J07519M

J07520M

J07521M

J07522M

J07523M

J07524M

J07525M

J07526M

J07527M

J07528M

J07529M

J07530M

J07531M

J07532M

J07533M

J07534M

J07535M

J07536M

J07538M

J07540M

J07541M

Description























J2594


Weight [lbs]: 14.91 7

MM



Product #: J72103

Contents

Description

J07510


J07512


J07513


J07514


J07515


J07516


J07517


J07518


J07520


J07521


J07522


J07523


J07524


J07526


J07527


J07528


J07529


J07530


J07531


J07532



6

INCH


Torx ® hex HEX

BLACK OXIDE




Product #: J73105

Contents

Description

J07512


J07513


J07514


J07515


J07516


J07517


J07518


J07519


J07520


J07521


J07522


J07523


J07524


J07525


J07526



J2594



6

INCH


Product #: J72105M

6

Contents

J07519M

J07520M

J07521M

J07522M

J07523M

J07524M

J07527M

J07530M

J07532M

J07536M

J07541M

Description












J07546M


Weight [lbs]: 13.33 7

MM


Product #: J07500-10

Contents

Description

J07512


J07513


J07514


J07515


J07516


J07517


J07518


J07519


J07520


J07521



6

INCH


Impact Socket Sets

3/4" Drive 10 Piece Metric Deep Impact Socket Set - 6 Point

Product #: J72100M

6

Contents

J07519ML

J07521ML

J07522ML

J07523ML

J07524ML

J07526ML

J07527ML

J07530ML

J07532ML

J07533ML

3/4" Drive 8 Piece Impact Socket Sets - 6 Point

Product #: J73103

Contents

J07516

J07517

J07518

J07520

J07521

J07522

J07523

Description












J2594



Description








J07524



MM

6

INCH


Product #: J73102

Contents

Description

J07516L


J07517L


J07518L


J07520L


J07521L


J07522L


J07523L


J07524L



6

INCH

Product #: J73104

Contents

Description

J07517


J07520


J07523


J07526


J07529


J07532


J07535


J07538



6

INCH


Torx ® hex HEX

BLACK OXIDE


3/4" Drive 7 Piece DEEP METRIC Impact Socket Set

Product #: J72102M

6


Contents

Description

J07526ML


J07527ML


J07530ML


J07532ML


J07535ML


J07536ML


J07538ML



MM


Product #: J72106M

12

Contents

Description

J07517MT Socket, Impact 3/4" DR 17mm 12 PT



























MM


Impact Socket Sets

3/4" Drive 15 Piece Deep Metric Impact Socket Set - 12 Point

Product #: J72104M

Contents

Description

12

MM

J07519MLT Socket, Impact Deep 3/4" DR 19 mm 12 PT

















3/4" Drive 13 Piece Impact Socket Set- 12 Point

Product #: J72104

Contents

Description

J07512T


J07513T


J07514T


J07515T


J07516T


J07517T


J07518T


J07519T


J07520T


J07521T


J07522T


J07523T


J07524T



12

INCH

3/4" Drive 5 Piece Impact Hex Bit socket Set

Product #: J07595


> > Size stamped on tool for easy identification.


Contents

Description

J075909/16 Socket, Impact 3/4" DR Hex Bit 9/16"




J075901 Socket, Impact 3/4" DR Hex Bit 1"

J2576 Socket Bar, 3/4" DR w/ 5 Clips - 9"


hex

INCH


Torx ® hex HEX

BLACK OXIDE


1" Drive 37 Piece Impact Socket Set - 6 Point

Product #: J76137

1" Drive impact Socket sets

6

INCH

Contents

J10012

J10013

J10014

J10015

J10016

J10017

J10018

J10019

J10020

J10021

J10022

J10023

J10024

J10025

J10026

J10027

J10028

J10029

J10030

Description

Socket, Impact 1" DR 3/4" 6 PT




Socket, Impact 1" DR 1" 6 PT

Socket, Impact 1" DR 1-1/16" 6 PT














Contents

Description

J10031


J10032


J10033


J10034


J10035


J10036


J10037


J10038


J10039


J10040


J10041


J10042


J10043


J10044


J10045


J10046


J10047


J10048




Impact Socket Sets

1" Drive 21 Piece Impact Socket

Set - 6 Point

1" Drive 21 Piece Deep Impact


Product #: J76122

6

INCH

Product #: J76121

6

INCH

1" Drive impact Socket Sets

Contents

Description

J10012


J10013


J10014


J10015


J10016


J10017


J10018


J10019


J10020


J10021


J10022


J10023


J10024


J10025


J10026


J10027


J10028


J10029


J10030


J10031


J10032



Contents

Description

J10012L

Socket, Impact Deep 1" DR 3/4" 6 PT

J10013L


J10014L


J10015L


J10016L

Socket, Impact Deep 1" DR 1" 6 PT

J10017L

Socket, Impact Deep 1" DR 1-1/16" 6 PT

J10018L


J10019L


J10020L


J10021L


J10022L


J10023L


J10024L


J10025L


J10026L


J10027L


J10028L


J10029L


J10030L


J10031L


J10032L




Torx ® hex HEX

BLACK OXIDE



Product #: J76116

6

1" Drive impact Socket sets

Contents

Description

J10033


J10034


J10035


J10036


J10037


J10038


J10039


J10040


J10041


J10042


J10043


J10044


J10045


J10046


J10047


J10048



INCH



Product #: J76115

6



Product #: J76111

6

INCH

INCH

Contents

Description

J10033L


J10034L


J10035L


J10036L


J10037L


J10038L


J10039L


J10040L


J10041L


J10042L


J10044L


J10045L


J10046L


J10047L


J10048L



Contents

Description

J10050L


J10052L


J10054L


J10056L


J10058L


J10060L


J10062L


J10064L


J10066L


J10068L


J10072L





Product #: J76109

6

Impact Socket Sets

Contents

Description

J10016


J10018


J10020


J10022


J10024


J10026


J10028


J10030


J10032



INCH


1" Drive 8 Piece Impact Socket Sets - 6 Point

Product #: J76102

Contents

Description

J10014


J10015


J10016


J10017


J10018


J10019


J10020


J10024



Product #: J76108

Contents

Description

J10014L Socket, Impact Deep 1" DR 7/8" 6 PT

J10015L Socket, Impact Deep 1" DR 15/16" 6 PT

J10016L Socket, Impact Deep 1" DR 1" 6 PT

J10017L Socket, Impact Deep 1" DR 1-1/16" 6 PT






6

INCH

6

INCH

Product #: J76103

Contents

Description

J10017


J10020


J10023


J10026


J10029


J10032


J10035


J10038



6

INCH


Torx ® hex HEX

BLACK OXIDE



1" Drive 8 Piece Metric Deep Impact Socket Set - 6 Point

Product #: J76104

Contents

Description

J10027ML Socket, Impact Deep 1" DR 27 mm 6 PT









6

MM


Product #: J76106

6

Contents

Description

J10041


J10044


J10047


J10050


J10056


J10062



INCH


Product #: J1001SS

Contents

Description

J10012SS


J10013SS


J10014SS


J10015SS


J10016SS


J10018SS


J10024SS



4

INCH


Impact Sockets

1/4" Drive Impact Sockets - 6 Point

> > Proto ® 6 Point Impact Sockets are ideal for use

on stubborn or damaged fasteners, and also on

fasteners made from soft materials.

>


> Socket size stamped on tool for easy identification.

>

>

>

B

A

D

E

L

C

Torx ® hex HEX BLACK OXIDE

Nut End Outside Drive End Outside Nut Depth Bolt Clearance Overall

INCH 6 Diameter (in) (B) Diameter (in) (C) (in) (D) Depth (in) (E) Length (in) (L) Weight (lbs)

3/16 J6906H 5/16 1/2 11/64 1/2 7/8 0.04

7/32 J6907H 11/32 1/2 13/64 1/2 7/8 0.03

1/4 J6908H 25/64 1/2 7/32 1/2 7/8 0.03

9/32 J6909H 7/16 1/2 15/64 1/2 7/8 0.03

5/16 J6910H 1/2 1/2 15/64 1/2 7/8 0.03

11/32 J6911H 33/64 33/64 17/64 1/2 7/8 0.04

3/8 J6912H 9/16 9/16 17/64 1/2 7/8 0.04

7/16 J6914H 21/32 21/32 5/16 1/2 7/8 0.05

1/2 J6916H 45/64 11/16 3/8 1/2 7/8 0.05

9/16 J6918H 51/64 51/64 3/8 1/2 7/8 0.08

5/8 J6920H 7/8 7/8 3/8 1/2 7/8 0.09

7 ASME B107.2


MM 6 Diameter (in) (B) Diameter (in) (C) (in) (D) Depth (in) (E) Length (in) (L) Weight (lbs)

4 J6904M 17/64 1/2 5/32 1/2 7/8 0.03

5 J6905M 5/16 1/2 3/16 1/2 7/8 0.04

5.5 J69055M 11/32 1/2 3/16 1/2 7/8 0.04

6 J6906M 25/64 1/2 7/32 1/2 7/8 0.03

7 J6907M 7/16 1/2 7/32 1/2 7/8 0.03

8 J6908M 1/2 1/2 7/32 1/2 7/8 0.04

9 J6909M 33/64 33/64 1/4 1/2 7/8 0.04

10 J6910M 9/16 9/16 1/4 1/2 7/8 0.04

11 J6911M 21/32 21/32 9/32 1/2 7/8 0.05

12 J6912M 11/16 11/16 19/64 1/2 7/8 0.06

13 J6913M 23/32 23/32 5/16 1/2 7/8 0.07

14 J6914M 51/64 51/64 3/8 1/2 7/8 0.08

15 J6915M 53/64 53/64 3/8 1/2 7/8 0.08

7 ASME B107.2


> Radius-corner socket design

> Engages flats for better grip

> Improves the ability to turn

worn or rounded fasteners

1/4" Drive impact Sockets

WARNING: WORK SAFELY WITH TOOLS. WEAR SAFETY GOGGLES. 507

+1.800.800.TOOL · Fax: +1.770.648.9108 · www.protoindustrial.com


1/4" Drive Deep Impact Sockets - 6 Point

> > Proto ® 6 Point Impact Sockets are ideal for use on

stubborn or damaged fasteners, and also on fasteners

made from soft materials.

> > Socket size stamped on tool for easy identification.


L

B

A

C

D

E



> > Improves the ability to turn




3/16 J6506H 5/16 1/2 1/4 1-5/8 2 0.08

7/32 J6507H 23/64 1/2 7/64 1-5/8 2 0.08

1/4 J6508H 25/64 1/2 9/32 1-5/8 2 0.08

9/32 J6509H 7/16 1/2 19/64 1-5/8 2 0.08

5/16 J6510H 1/2 1/2 5/16 1-5/8 2 0.07

11/32 J6511H 33/64 33/64 11/32 1-5/8 2 0.07

3/8 J6512H 9/16 9/16 3/8 1-5/8 2 0.09

7/16 J6514H 21/32 21/32 3/8 1-5/8 2 0.12

1/2 J6516H 11/16 11/16 7/16 1-5/8 2 0.12

9/16 J6518H 51/64 51/64 7/16 1-5/8 2 0.15

5/8 J6520H 7/8 7/8 7/16 1-5/8 2 0.12

7 ASME B107.2



5 J6505MH 5/16 1/2 1/4 1-5/8 2 0.08

5.5 J65055MH 23/64 1/2 17/64 1-5/8 2 0.09

6 J6506MH 25/64 1/2 9/32 1-5/8 2 0.08

7 J6507MH 7/16 1/2 19/64 1-5/8 2 0.08

8 J6508MH 1/2 1/2 5/16 1-5/8 2 0.07

9 J6509MH 33/64 33/64 5/16 1-5/8 2 0.07

10 J6510MH 9/16 9/16 3/8 1-5/8 2 0.08

11 J6511MH 21/32 21/32 3/8 1-5/8 2 0.11

12 J6512MH 11/16 11/16 13/32 1-5/8 2 0.13

13 J6513MH 23/32 23/32 7/16 1-5/8 2 0.14

14 J6514MH 51/64 51/64 7/16 1-5/8 2 0.18

15 J6515MH 53/64 53/64 7/16 1-5/8 2 0.18

7 ASME B107.33M



Impact Sockets

1/4" Drive Universal Impact Sockets - 12 Point



BLACK OXIDE > > Radius-corner socket design

Drive End


Outside Overall

INCH 12


Diameter (in) Length (in) Weight (lbs)


Torx ® hex HEX

1/4 J66308P 5/8 1-9/32 0.27

5/16 J66310P 5/8 1-11/32 0.27

3/8 J66312P 5/8 1-15/32 0.3

7/16 J66314P 5/8 1-1/2 0.32

1/2 J66316P 5/8 1-5/8 0.33

7

Drive End

Outside Overall

MM 12 Diameter (in) Length (in) Weight (lbs)

5.5 J66555MP 5/8 1-1/4 0.27

6 J66506MP 5/8 1-9/32 0.27

7 J66507MP 5/8 1-5/16 0.27

8 J66508MP 5/8 1-11/32 0.28

9 J66509MP 5/8 1-3/8 0.3

10 J66510MP 5/8 1-7/16 0.31

11 J66511MP 5/8 1-1/2 0.31

12 J66512MP 5/8 1-17/32 0.32

13 J66513MP 5/8 1-19/32 0.32

7

> Used wherever powered drive tools are used to install or remove fasteners.

tools in repetitive application.

> > Features two through holes and a groove to accept a Proto ® Retaining Ring

or pin and O-ring to help secure the socket to the drive tool anvil.

> > Position at appropriate angle to turn fasteners where obstructions prevent

a straight application.



Drive End

INCH

Outside Overall

Product # Diameter (in) Length (in) Weight (lbs)

1/4 J66170P 5/8 1-3/8 0.27

7

1/4" Drive Impact Universal Joint


>

> > Designed to withstand the high torque and force associated with impact

1/4" Drive Torx ® Impact Sockets

> > Made of alloy steel.

> > Black oxide finish.

> > For use with Torx ® style fasteners.

Torx ® Size

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Bolt Clearance

Depth (in) (E)

Overall

Length (in) (L) Weight (lbs)

TORX ®

E4 J6904TX 1/4 7/16 13/64 2/23 1 0.03

E5 J6905TX 1/4 7/16 7/32 2/17 1 0.04

E6 J6906TX 5/16 7/16 15/64 1/7 1 0.02

E7 J6907TX 21/64 1/2 9/32 2/13 1 0.03

E8 J6908TX 3/8 19/64 19/64 11/651 1 0.03

E10 J6910TX 1/2 1/2 11/32 13/59 1 0.05

E12 J6912TX 9/16 9/16 25/64 19/68 1 0.05


7
















1/4 J7208H 7/16 11/16 9/32 19/32 1-3/32 0.07

9/32 J7209H 31/64 11/16 5/16 19/32 1-3/32 0.07

5/16 J7210H 1/2 11/16 5/16 19/32 1-3/32 0.07

11/32 J7211H 35/64 11/16 3/8 19/32 1-3/32 0.07

3/8 J7212H 19/32 11/16 3/8 19/32 1-3/32 0.07

7/16 J7214H 11/16 11/16 3/8 19/32 1-3/32 0.06

1/2 J7216H 3/4 3/4 3/8 19/32 1-3/32 0.08

9/16 J7218H 13/16 13/16 9/16 19/32 1-3/32 0.11

5/8 J7220H 29/32 29/32 9/16 19/32 1-3/32 0.12

11/16 J7222H 1 1 9/16 19/32 1-3/32 0.15

3/4 J7224H 1-1/16 1-1/16 17/32 19/32 1-3/32 0.16

13/16 J7226H 1-3/16 1-13/64 11/16 23/32 1-7/32 0.24

7/8 J7228H 1-9/32 1-9/32 11/16 23/32 1-7/32 0.26

15/16 J7230H 1-23/64 1-23/64 51/64 27/32 1-11/32 0.35

1 J7232H 1-1/2 1-1/2 51/64 27/32 1-11/32 0.42

7 ASME B107.2

L

B

A

C

D

E




6 J7206M 27/64 11/16 7/32 27/64 59/64 0.06

7 J7207M 31/64 11/16 15/64 27/64 59/64 0.06

8 J7208M 33/64 11/16 5/16 17/32 1-1/32 0.06

9 J7209M 37/64 11/16 11/32 17/32 1-1/32 0.06

10 J7210M 11/16 11/16 3/8 17/32 1-1/32 0.06

11 J7211M 11/16 11/16 13/32 17/32 1-1/32 0.06

12 J7212M 23/32 23/32 7/16 17/32 1-1/32 0.07

13 J7213M 3/4 3/4 7/16 17/32 1-3/32 0.08

14 J7214M 13/16 13/16 9/16 19/32 1-3/32 0.09

15 J7215M 55/64 55/64 9/16 19/32 1-3/32 0.10

16 J7216M 29/32 29/32 9/16 19/32 1-3/32 0.12

17 J7217M 1 1 9/16 19/32 1-3/32 0.15

18 J7218M 1-1/32 1-1/32 9/16 19/32 1-3/32 0.16

19 J7219M 1-1/16 1-1/16 17/32 19/32 1-3/32 0.15

20 J7220M 1-7/64 1-7/64 17/32 19/32 1-3/32 0.18

21 J7221M 1-5/32 1-5/32 17/32 19/32 1-3/32 0.19

22 J7222M 1-13/64 1-13/64 17/32 19/32 1-3/32 0.20

23 J7223M 1-1/4 1-1/4 17/32 19/32 1-3/32 0.26

24 J7224M 1-19/64 1-19/64 17/32 19/32 1-3/32 0.27

7 ASME B107.33M


Impact Sockets


> > Proto ® 8 Point Impact Sockets are ideal for use on stubborn or damaged

fasteners, and also on fasteners made from soft materials.

> > Drive end chamfer and four detents help provide quick positive engagement

with drive tool on any of the socket drive walls.


> > Large clearance holes, concentric opening and nut end chamfer make it easy

to position socket on fasteners.

> > Made from high strength steel to help minimize wall thickness and provide

access to fasteners in recesses and where nuts and bolts protrude.

> > Impact sockets are used wherever powered drive tools are used to install or

remove fasteners.

> > Impact sockets are designed to withstand higher torque and force

associated with impact tools in repetitive application.





1/4 J7208S 31/64 11/16 1/4 1/2 1 0.07

5/16 J7210S 5/8 11/16 9/32 1/2 1 0.06

3/8 J7212S 11/16 11/16 5/16 1/2 1 0.06

7/16 J7214S 13/16 13/16 21/64 1/2 1 0.10

1/2 J7216S 59/64 15/16 3/8 9/16 1-1/16 0.13

9/16 J7218S 1-3/32 1-3/16 9/16 5/8 1-1/8 0.17

7 ASME B107.2

8 PT Impact Sockets

Sometimes called “double square sockets”, 8 point

sockets gives the mechanic twice the angles of attack

when trying to fit a socket over a 4 point fastener.

These fasteners are often found in heavy industry

or agricultural equipment, especially older units;

but even these older standards can be found on

modern equipment. 4 Point fasteners can also be

found on square pipe plugs, transmission drains, fill

plugs on hydraulic tanks, adjusters for drum brakes,

square-headed cylinder bolts, and various taps.

Normally, 4 point sockets are recommended for 4 point

fasteners, but they give you only four opportunities to seat

the socket over the fastener - north, east, south, and west.

An 8 point socket doubles the numbers, allowing a

mechanic to reach a socket in between the other angles.

With an 8 point socket, there is still plenty of contact

with the fastener to get a firm grip on the head.


>

>

>

B

A

L

C






D

E

Four approaches

using a 4 PT socket.

Eight approaches












L

B

A

C

D

E







1/4 J7708H 7/16 11/16 9/32 2-1/4 2-3/4 0.21

9/32 J7709H 31/64 11/16 5/16 2-1/4 2-3/4 0.18

5/16 J7710H 33/64 11/16 21/64 2-1/4 2-3/4 0.20

11/32 J7711H 35/64 11/16 11/32 2-1/4 2-3/4 0.19

3/8 J7712H 19/32 11/16 3/8 2-1/4 2-3/4 0.19

7/16 J7714H 11/16 11/16 27/64 2-1/4 2-3/4 0.17

1/2 J7716H 3/4 3/4 15/32 2-1/4 2-3/4 0.21

9/16 J7718H 13/16 13/16 11/16 2-1/4 2-3/4 0.22

5/8 J7720H 29/32 29/32 11/16 2-1/4 2-3/4 0.29

11/16 J7722H 1 1 11/16 2-1/4 2-3/4 0.34

3/4 J7724H 1-1/16 1-1/16 43/64 2-1/4 2-3/4 0.38

13/16 J7726H 1-13/64 1-13/64 13/16 2-1/8 2-3/4 0.53

7/8 J7728H 1-9/32 1-9/32 13/16 2-1/8 2-3/4 0.59

15/16 J7730H 1-23/64 1-23/64 13/16 2-1/8 2-3/4 0.66

1 J7732H 1-1/2 1-1/2 13/16 2-1/8 2-3/4 0.85

7 ASME B107.2



6 J7006M 27/64 11/16 9/32 2-1/4 2-3/4 0.19

7 J7007M 31/64 11/16 5/16 2-1/4 2-3/4 0.20

8 J7008M 33/64 11/16 5/16 2-1/4 2-3/4 0.19

9 J7009M 37/64 11/16 3/8 2-1/4 2-3/4 0.20

10 J7010M 5/8 11/16 3/8 2-1/4 2-3/4 0.19

11 J7011M 11/16 11/16 13/32 2-1/4 2-3/4 0.18

12 J7012M 3/4 3/4 7/16 2-1/4 2-3/4 0.20

13 J7013M 3/4 3/4 15/32 2-1/4 2-3/4 0.22

14 J7014M 13/16 13/16 1/2 2-1/4 2-3/4 0.22

15 J7015M 55/64 55/64 11/16 2-1/4 2-3/4 0.25

16 J7016M 29/32 29/32 11/16 2-1/4 2-3/4 0.29

17 J7017M 1 1 11/16 2-1/4 2-3/4 0.37

18 J7018M 1-1/32 1-1/32 11/16 2-1/4 2-3/4 0.38

19 J7019M 1-1/16 1-1/16 11/16 2-1/4 2-3/4 0.38

20 J7020M 1-7/64 1-7/64 25/32 2-1/4 2-3/4 0.42

21 J7021M 1-5/32 1-5/32 25/32 2-1/4 2-3/4 0.46

22 J7022M 1-13/64 1-13/64 51/64 2-1/4 2-3/4 0.49

23 J7023M 1-1/4 1-1/4 51/64 2-1/4 2-3/4 0.53

24 J7024M 1-19/64 1-19/64 59/64 2-1/4 2-3/4 0.58

7 ASME B107.33M


Impact Sockets

3/8" Drive Deep Thin Wall Impact Sockets - 6 Point


> > Reduced wall thickness helps improve access to fasteners in

restricted areas.




> > Proto ® 6 Point Impact Sockets are ideal for use on stubborn or

damaged fasteners, and also on fasteners made from soft materials.



> > Thinner walls help improve productivity by making it easier to gain



> > Often used in application where fasteners are close together, such

as tire service.

>

>

>

L




1/4 J7708HT 27/64 11/16 9/32 1-15/32 2 0.15

5/16 J7710HT 31/64 11/16 1/4 1-15/32 2 0.14

11/32 J7711HT 1/2 11/16 9/32 1-15/32 2 0.13

3/8 J7712HT 37/64 11/16 5/16 1-7/32 2 0.13

7/16 J7714HT 41/64 11/16 11/32 1-7/32 2 0.11

1/2 J7716HT 23/32 23/32 13/32 1-7/32 2 0.14

9/16 J7718HT 25/32 25/32 1/2 1-15/32 2 0.15

5/8 J7720HT 7/8 7/8 1/2 1-19/32 2-1/8 0.18

11/16 J7722HT 15/16 15/16 1/2 1-11/16 2-7/32 0.22

3/4 J7724HT 1 1 17/32 1-23/32 2-1/4 0.27

7/8 J7728HT 1-7/32 1-7/32 13/16 1-31/32 2-1/2 0.43

15/16 J7730HT 1-1/4 1-1/4 13/16 2-5/16 2-13/16 0.54

7 ASME B107.2



8 J7008MHT 31/64 11/16 1/4 1-1/4 1-3/4 0.11

9 J7009MHT 17/32 11/16 5/16 1-3/16 1-3/4 0.15

10 J7010MHT 19/32 11/16 11/32 1-5/32 1-3/4 0.11

11 J7011MHT 11/16 11/16 21/64 1-11/64 1-3/4 0.12

12 J7012MHT 11/16 11/16 3/8 1-1/8 1-3/4 0.11

13 J7013MHT 45/64 45/64 13/32 1-3/32 1-3/4 0.11

14 J7014MHT 25/32 25/32 15/32 1-1/32 2 0.14

15 J7015MHT 53/64 53/64 1/2 1 2-5/64 0.18

16 J7016MHT 7/8 7/8 1/2 1 2-5/64 0.17

17 J7017MHT 1 1 1/2 1 2-5/64 0.20

18 J7018MHT 31/32 31/32 1/2 1 2-5/64 0.20

19 J7019MHT 1 1 17/32 31/32 2-5/64 0.25






B

A

C

D

E

7






> > Made of heat-treated alloy steel.



> > For use with Torx ® style fasteners.

Torx ® Size

Overall

Length (in) Weight (lbs)

TORX ®

E6 J7206TX 1-1/4 0.06

E7 J7207TX 1-1/4 0.07

E8 J7208TX 1-1/4 0.07

E10 J7210TX 1-1/4 0.07

E12 J7212TX 1-1/4 0.07

E14 J7214TX 1-1/4 0.09

E16 J7216TX 1-1/4 0.10

7

3/8" Drive Impact Hex Bit Sockets



> > Hex bit impact sockets are used wherever powered drive tools are used





INCH

hex

Bit Overall

Length (in) Length (in) Weight (lbs)

1/8 J72901/8 1-5/8 2-23/32 0.07

5/32 J72905/32 1-5/8 2-23/32 0.08

3/16 J72903/16 1-5/8 2-23/32 0.08

7/32 J72907/32 1-5/8 2-23/32 0.09

1/4 J72901/4 1-5/8 2-23/32 0.10

5/16 J72905/16 1-5/8 2-23/32 0.13

3/8 J72903/8 1-5/8 2-23/32 0.14

7

MM

hex

Bit

Length (in)

Overall

Length (in)

Weight (lbs)

4 J7290-4M 1-5/8 2-23/32 0.07

5 J7290-5M 1-5/8 2-23/32 0.08

6 J7290-6M 1-5/8 2-23/32 0.09

8 J7290-8M 1-5/8 2-23/32 0.12

10 J7290-10M 1-5/8 2-23/32 0.14

7



Impact Sockets

3/8" Drive Impact Universal Sockets - 6 & 12 Point



> > Proto ® 6 Point Impact Sockets are ideal for use on stubborn

BLACK OXIDE > > Radius-corner socket design


or damaged fasteners, and also on fasteners made from soft


Torx ® hex HEX

materials.


B

E

D

L

C

Drive End Outside Nut Depth Bolt Clearance Overall

MM 6 12 Diameter (in) (C) (in) (D) Depth (in) (E) Length (in) (L) Weight (lbs)

8 J77408MP - 15/16 7/16 7/16 2 0.26

10 J77410MP J77510MP 15/16 7/16 7/16 2 0.21

11 J77411MP J77511MP 15/16 7/16 7/16 2 0.22

12 J77412MP J77512MP 15/16 7/16 7/16 2-1/32 0.22

13 J77413MP J77513MP 15/16 7/16 7/16 2-1/32 0.23

14 J77414MP J77514MP 15/16 7/16 7/16 2-1/16 0.23

15 J77415MP J77515MP 15/16 7/16 7/16 2-1/16 0.24

16 J77416MP J77516MP 15/16 7/16 7/16 2-3/32 0.25

17 J77417MP J77517MP 15/16 7/16 7/16 2-1/8 0.26

18 J77418MP J77518MP 15/16 7/16 7/16 2-1/8 0.28

19 J77419MP J77519MP 15/16 7/16 7/16 2-1/8 0.28



3/8 J77273P 9/16 61/64 7/16 7/16 1-57/64 0.30

7/16 J77274P 21/32 61/64 7/16 7/16 1-63/64 0.31

1/2 J77275P 3/4 61/64 7/16 7/16 2-1/64 0.32

9/16 J77276P 13/16 61/64 7/16 7/16 2-1/64 0.33

5/8 J77277P 29/32 61/64 7/16 7/16 2-5/64 0.35

11/16 J77278P 1 61/64 7/16 7/16 2-7/64 0.29

3/4 J77279P 1-1/16 61/64 7/16 7/16 2-7/64 0.29

7 ASME B107.2


7




3/8" Drive impact Universal Joints & adapters

3/8" Drive Metric Deep Universal

Impact Sockets - 6 Point

> > Ball and spring design which allows for a 30°

working angle.





E

Drive End Outside Nut Depth Bolt Clearance Depth Overall

MM 6

Diameter (in) (C) (in) (D)

(in) (E)


10 J78410MP 15/16 3/8 1 2 0.24

11 J78411MP 15/16 3/8 1 2-1/2 0.25

12 J78412MP 15/16 3/8 1 2-1/32 0.28

13 J78413MP 15/16 13/32 1-1/32 2-1/32 0.28

14 J78414MP 15/16 13/32 1-1/32 2-1/16 0.3

15 J78415MP 15/16 13/32 1-1/32 2-1/16 0.31

16 J78416MP 15/16 7/16 1-1/16 2-3/32 0.32

17 J78417MP 15/16 7/16 1-1/8 2-1/8 0.36

18 J78418MP 15/16 15/32 1-1/8 2-1/8 0.36

19 J78419MP 15/16 1/2 1-9/64 2-1/8 0.38

C

B

D

L





3/8" Drive Impact

Universal Joint


>

> Used wherever powered drive tools are used


> > Designed to withstand the high torque and force associated

with impact tools in repetitive application.

> > Features two through holes and a groove to accept a Proto ® Retaining

Ring or pin and O-ring to help secure the socket to the drive tool anvil.

> > Position at appropriate angle to turn fasteners where

obstructions prevent a straight application.



3/8" Drive Impact Adapters

> > Use adapters to help increase or decrease drive end size.

> > Do not use hand adapters with power tools.

>

> Do not over torque small sockets when using them with adapters on

large drive tools.



Drive End

Outside Overall

INCH Product # Diameter (in) Length (in) Weight (lbs)

3/8 J77270P 15/16 2-1/32 0.21

7

INCH

Overall

Size (in) Length (in) Weight (lbs)

J7653 3/4" F x 1/2" M 2-1/16 0.48

J7650 3/8" F x 1/2" M 1-5/16 0.13

J7651 1/2" F x 3/8" M 1-7/16 0.12

7 ASME B107.2


Impact Sockets

3/8" Drive Impact Extensions

> > Use extensions to gain access to fasteners in locations that would

otherwise be difficult to reach.

> > Male square is oriented in line with female squares for use with fixed

head torque wrenches.

> > Full chamfer at drive opening (when applicable) for easy engagement

with drive tools.





Product #

Overall

Length (in)

Weight (lbs)

J7175P 3 0.16

J7176P 6 0.32

J7178P 12 0.64

7 ASME B107.2

3/8" Drive Impact Locking Extensions


> > Easy operating spring loaded locking mechanism.

Product #

Overall

Length (in)

Weight (lbs)

J7203L 3 0.25

J7206L 6 0.41

J7212L 12 0.75

3/8" Drive Hand Impact Driver

> > Designed to loosen hard to turn bolts and screws.

> > Heavy-Duty spring for added torque.

7

3/8" Drive impact EXTENSIONS,DRIVERS & RETAINING RINGS

Overall

Product #

Length (in)

Weight (lbs)

J7099 5-1/2 1.68

7

3/8" Drive Retaining Rings

> > Proto ® 3/8" Drive Retaining Rings have a one-piece, without a crush gauge.

Product # Description For Groove Dia. (in) Diameter (in) Height (in) Weight (lbs)

JRR37560 Retaining Ring, 3/8" DR 600 GRV 19/32 11/16 1/16 0.01




JRR37595 Retaining Ring, 3/8" DR 950 GRV 61/64 1 1/16 0.01

JRR37511 Retaining Ring, 3/8" DR 1100 GRV 1-3/32 1-3/16 1/16 0.01



Torx ® hex HEX

BLACK OXIDE




1/2" Drive Impact Sockets




INCH 6 12

Nut End Outside Drive End Outside

Diameter (in) (B) Diameter (in) (C)

Nut Depth

(in) (D)

Bolt Clearance

Depth (in) (E)

Overall

Length (in) (L)

Weight (lbs)

3/8 J7412H J7412 41/64 15/16 11/32 27/32 1-1/2 0.17

7/16 J7414H J7414 23/32 15/16 13/32 27/32 1-1/2 0.18

1/2 J7416H J7416 51/64 15/16 13/32 27/32 1-1/2 0.18

9/16 J7418H J7418 7/8 15/16 7/16 27/32 1-1/2 0.18

5/8 J7420H J7420 1 1 1/2 27/32 1-1/2 0.20

11/16 J7422H J7422 1-1/32 1-1/32 1/2 27/32 1-1/2 0.22

3/4 J7424H J7424 1-7/64 1-7/64 51/64 27/32 1-1/2 0.24

13/16 J7426H J7426 1-13/64 1-13/64 11/16 31/32 1-5/8 0.31

7/8 J7428H J7428 1-17/64 1-9/32 43/64 31/32 1-5/8 0.34

15/16 J7430H J7430 1-23/64 1-23/64 51/64 1-3/32 1-3/4 0.44

1 J7432H J7432 1-1/2 1-1/2 25/32 1-3/32 1-3/4 0.55

1-1/16 J7434H J7434 1-33/64 1-33/64 25/32 1-3/32 1-3/4 0.53

1-1/8 J7436H J7436 1-19/32 1-19/32 25/32 1-1/32 2 0.65

1-3/16 J7438H J7438 1-19/32 1-19/32 3/4 1-1/64 2 0.85

1-1/4 J7440H J7440 1-3/4 1-3/4 3/4 1-3/4 2 0.78

1-5/16 J7442H J7442 1-3/4 1-3/4 13/16 63/64 2 0.73

1-3/8 J7444H J7444 1-51/64 1-5/8 15/16 1-3/32 2-1/8 0.72

1-7/16 J7446H J7446 1-59/64 1-5/8 1 1-37/64 2-15/64 0.87

1-1/2 J7448H J7448 2 1-5/8 1 1-37/64 2-15/64 1.03

1-9/16 J7450H – 2-1/32 1-5/8 1 1-1/2 2-1/4 1.16

7 ASME B107.2

MM 6 12

L

B

A

C

D



E

Nut Depth

(in) (D)

Bolt Clearance

Depth (in) (E)





Overall

Length (in) (L)

Weight (lbs)

8 J7408M – 37/64 15/16 9/32 27/32 1-1/2 0.18

9 J7409M – 41/64 15/16 3/8 27/32 1-1/2 0.18

10 J7410M J7410MT 43/64 15/16 3/8 27/32 1-1/2 0.18

11 J7411M J7411MT 23/32 15/16 3/8 27/32 1-1/2 0.18

12 J7412M J7412MT 51/64 15/16 13/32 27/32 1-1/2 0.17

13 J7413M J7413MT 51/64 15/16 7/16 27/32 1-1/2 0.16

14 J7414M J7414MT 7/8 15/16 15/32 27/32 1-1/2 0.18

15 J7415M J7415MT 15/16 15/16 1/2 27/32 1-1/2 0.18

16 J7416M J7416MT 1 1 17/32 27/32 1-1/2 0.20

17 J7417M J7417MT 1-1/32 1-1/32 9/16 27/32 1-1/2 0.22

18 J7418M J7418MT 1-1/8 1-1/8 51/64 27/32 1-1/2 0.27

19 J7419M J7419MT 1-7/64 1-7/64 47/64 27/32 1-1/2 0.25

20 J7420M J7420MT 1-5/32 1-5/32 11/16 31/32 1-5/8 0.30

21 J7421M J7421MT 1-13/64 1-13/64 43/64 31/32 1-5/8 0.30

22 J7422M J7422MT 1-9/32 1-9/32 43/64 31/32 1-5/8 0.36

23 J7423M J7423MT 1-3/8 1-3/8 43/64 31/32 1-5/8 0.39

24 J7424M J7424MT 1-23/64 1-23/64 43/64 31/32 1-5/8 0.43

25 J7425M – 1-3/8 1-3/8 51/64 1-3/32 1-3/4 0.48

26 J7426M – 1-1/2 1-1/2 1-1/32 1-11/32 2 0.54

27 J7427M – 1-1/2 1-1/2 1-1/32 1-11/32 2 0.62

28 J7428M – 1-5/8 1-5/8 1-1/32 1-11/32 2 0.72

29 J7429M – 1-5/8 1-5/8 1-1/64 1-11/32 2 0.67

30 J7430M J7430MT 1-33/64 1-33/64 25/32 1-3/32 2 0.82

31 J7431M – 1-33/64 1-33/64 51/64 1-3/32 2 0.83

32 J7432M J7432MT 1-33/64 1-33/64 51/64 1-3/32 2 0.75

33 J7433M – 1-27/32 1-27/32 1-1/64 1-9/32 2 0.95

34 J7434M – 1-29/32 1-29/32 1-1/64 1-9/32 2 1.00

36 J7436M – 2-1/64 2-1/64 1-3/16 1-11/32 2 0.89

38 J7438M – 2-5/32 2-5/32 1-3/16 1-11/32 2-3/8 0.96

41 J7441M – 2-19/64 2-19/64 1-21/64 1-17/32 2-3/8 1.20

46 J7446M – 2-3/8 2-3/8 63/64 1-17/32 2-7/16 1.24

7 ASME B107.33M


Impact Sockets

IMPACT SOCKET SAFETY

Impact sockets are manufactured specifically to work

well and fail safely with impact tools. Impact sockets have

many safety features that are simply not present in hand

sockets, so it is important to use ONLY impact sockets

on an impact tool. Impact sockets protect both the tool

and the mechanic by absorbing much of the punishing

vibration delivered by the anvil of the impact tool.

THE IMPORTANCE OF SOFTNESS

An important safety feature found in an impact socket

is the metal. The alloy is heat-treated to just the right

amount to create a metal hard enough to do the job,

but soft enough to wear but not break over time.

FAILING SAFELY

For the user, impact sockets will fail safely by deforming

in one piece. Hand sockets, made from a harder

steel, can shatter or fly apart when they fail if used

on an impact tool, causing potential injuries to anyone

nearby, as those pieces can fly off at high speeds.

PROTECTING YOUR TOOL

Chrome hand sockets also punish the impact tool by

reflecting the torque vibration back into the anvil of the

tool. These tools expect the impact socket to absorb much

of the heavy vibrations, so hand sockets will wear down an

impact tool much faster than impact socket ever would.

CRUSH-GAUGE SAFETY RINGS

Another safety feature found on most

larger impact sockets are the safety ring

grooves found at the bottom of the impact

sockets. These are fittings for safety

rings, especially the crush gauge ring,

which tells you if the socket is not precisely

fitted to the anvil during operation. A

crush ring is an important early warning

device that a socket may be wearing out.

TORQUEPLUS FOR IMPACT SOCKETS

By moving the point of contact away from the

points of the fastener, TorquePlus helps to

minimize rounding and keeps the contact point flush

and tight against the side of the fastener.


EYE PROTECTION

Always remember to wear eye protection or a face

shield when working with impact tools. They are

important protections against unexpected events.

High quality impact steel has

higher consistency and fewer

aberrations for a higher lifetime of

wear and safety.

TorquePlus for Impact Sockets

is found on all but the very

largest and the very smallest

impact sockets.


Torx ® hex HEX

BLACK OXIDE








> > Large clearance holes, concentric opening and nut end chamfer make it


> > Made from high-strength steel to help minimize wall thickness and provide


> > Impact sockets are used wherever powered drive tools are used to install

or remove fasteners.

> > Impact sockets are designed to withstand higher torque and force






L

B

A

C

D

E







3/8 J7412S 47/64 15/16 17/64 27/32 1-1/2 0.17

7/16 J7414S 53/64 15/16 19/64 27/32 1-1/2 0.18

1/2 J7416S 15/16 15/16 11/32 27/32 1-1/2 0.18

9/16 J7418S 1-1/32 1-1/32 3/8 27/32 1-1/2 0.21

5/8 J7420S 1-1/8 1-1/8 27/32 27/32 1-1/2 0.26

11/16 J7422S 1-3/16 1-3/16 27/32 27/32 1-1/2 0.27

3/4 J7424S 1-11/32 1-11/32 27/32 27/32 1-1/2 0.37

13/16 J7426S 1-3/8 1-3/8 27/32 27/32 1-1/2 0.39

7/8 J7428S 1-1/2 1-1/2 31/32 31/32 1-5/8 0.48

15/16 J7430S 1-5/8 1-5/8 1-1/64 1-3/32 1-3/4 0.62

1 J7432S 1-3/4 1-3/4 1-1/64 1-3/32 1-3/4 0.74

1-1/16 J7434S 1-27/32 1-27/32 1-1/64 1-11/32 1-3/4 0.91

7 ASME B107.2

8 PT Impact Sockets

Sometimes called “double square sockets”, 8 point

sockets gives the mechanic twice the angles of attack

when trying to fit a socket over a 4 point fastener.

These fasteners are often found in heavy industry

or agricultural equipment, especially older units;

but even these older standards can be found on

modern equipment. 4 Point fasteners can also be

found on square pipe plugs, transmission drains, fill

plugs on hydraulic tanks, adjusters for drum brakes,

square-headed cylinder bolts, and various taps.

Normally, 4 point sockets are recommended for 4 point

fasteners, but they give you only four opportunities to seat

the socket over the fastener - north, east, south, and west.

Four approaches


Eight approaches


An 8 point socket doubles the numbers, allowing a

mechanic to reach a socket in between the other angles.

With an 8 point socket, there is still plenty of contact

with the fastener to get a firm grip on the head.


Impact Sockets

1/2" Drive Deep Impact Sockets






INCH 6 12

L



B

A

C

D

E

Nut Depth

(in) (D)

Bolt Clearance

Depth (in) (E)

Overall

Length (in) (L)

Weight (lbs)

3/8 J7312H J7312 19/32 15/16 15/16 2-5/8 3-1/4 0.42

7/16 J7314H J7314 23/32 15/16 11/32 1-5/8 3-1/4 0.44

1/2 J7316H J7316 1-25/32 15/16 7/16 1-5/8 3-1/4 0.43

9/16 J7318H J7318 7/8 15/16 1/2 1-5/8 3-1/4 0.41

5/8 J7320H J7320 1 1 9/16 1-5/8 3-1/4 0.44

11/16 J7322H J7322 1-1/32 1-1/32 5/8 2-5/8 3-1/4 0.47

3/4 J7324H J7324 1-7/64 1-1/8 1-5/32 2-5/8 3-1/4 0.53

13/16 J7326H J7326 1-3/16 1-3/16 1-5/32 2-5/8 3-1/4 0.62

7/8 J7328H J7328 1-19/64 1-9/32 1-13/32 2-7/8 3-1/2 0.78

15/16 J7330H J7330 1-3/8 1-3/8 1-13/32 2-7/8 3-1/2 0.86

1 J7332H J7332 1-1/2 1-1/2 1-13/32 2-7/8 3-1/2 1.02

1-1/16 J7334H J7334 1-1/2 1-33/64 1-17/32 2-7/8 3-1/2 1.11

1-1/8 J7336H J7336 1-5/8 1-5/8 1-13/32 2-7/8 3-1/2 1.20

1-3/16 J7338H J7338 1-13/16 1-21/32 1-1/64 2-7/8 3-1/2 1.47

1-1/4 J7340H J7340 1-13/16 1-21/32 1-1/64 2-7/8 3-1/2 1.39

1-5/16 J7342H J7342 1-7/8 1-21/32 1-1/16 2-7/8 3-1/2 1.41

1-3/8 J7344H J7344 1-7/8 1-21/32 1-7/64 2-7/8 3-1/2 1.31

1-7/16 J7346H J7346 2-1/16 1-21/32 1-5/32 2-7/8 3-1/2 1.67

1-1/2 J7348H J7348 2-1/16 1-21/32 1-13/64 2-7/8 3-1/2 1.50

1-9/16 J7350H – 2 1-5/8 1-1/4 1-1/4 3-1/2 1.80

7 ASME B107.2

MM 6

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Bolt Clearance Depth

(in) (E)





Overall

Length (in) (L)

Weight (lbs)

8 J7308M 37/64 7/8 5/16 2-19/32 3-1/4 0.37

9 J7309M 19/32 7/8 3/8 2-19/32 3-1/4 0.36

10 J7310M 41/64 15/16 7/16 2-19/32 3-1/4 0.43

11 J7311M 45/64 15/16 7/16 2-19/32 3-1/4 0.43

12 J7312M 47/64 15/16 1/2 2-19/32 3-1/4 0.43

13 J7313M 25/32 15/16 1/2 2-19/32 3-1/4 0.42

14 J7314M 55/64 15/16 1/2 2-19/32 3-1/4 0.40

15 J7315M 15/16 1 37/64 2-19/32 3-1/4 0.40

16 J7316M 1 1-1/32 19/32 2-19/32 3-1/4 0.46

17 J7317M 1-1/32 1-1/16 5/8 2-19/32 3-1/4 0.45

18 J7318M 1-1/16 1-1/16 43/64 2-19/32 3-1/4 0.49

19 J7319M 1-7/64 1-7/64 1-5/32 2-19/32 3-1/4 0.52

20 J7320M 1-5/32 1-5/32 1-5/32 2-19/32 3-1/4 0.55

21 J7321M 1-13/64 1-13/64 1-13/32 2-19/32 3-1/4 0.66

22 J7322M 1-9/32 1-9/32 1-13/32 2-27/32 3-1/2 0.75

23 J7323M 1-19/64 1-19/64 1-13/32 2-27/32 3-1/2 0.75

24 J7324M 1-23/64 1-23/64 1-13/32 2-27/32 3-1/2 0.81

25 J7325M 1-7/16 1-7/16 1-13/32 2-27/32 3-1/2 0.92

26 J7326M 1-1/2 1-1/2 1-13/32 2-27/32 3-1/2 1.03

27 J7327M 1-9/16 1-9/16 1-13/32 2-27/32 3-1/2 1.14

28 J7328M 1-5/8 1-5/8 1-13/32 2-27/32 3-1/2 1.20

29 J7329M 1-5/8 1-5/8 1-33/64 2-27/32 3-1/2 1.16

30 J7330M 1-11/16 1-11/16 1-13/32 2-27/32 3-1/2 1.53

32 J7332M 1-25/32 1-25/32 1-13/64 2-27/32 3-1/2 1.32

33 J7333M 1-55/64 1-55/64 1-25/64 2-27/32 3-1/2 1.48

34 J7334M 1-15/16 1-15/16 1-25/64 2-27/32 3-1/2 1.50

35 J7335M 2-1/16 2-1/16 1-25/64 2-27/32 3-1/2 1.61

36 J7336M 2-1/16 2-1/16 1-25/64 2-27/32 3-1/2 1.63

7 ASME B107.33M









> > Reduced wall thickness helps improve access

to fasteners in restricted areas.








> > Thinner walls help improve productivity by making it easier

to gain access to fasteners in confined spaces.


> > Often used in application where fasteners are

close together, such as tire service.

L




B

A

D

E

C


INCH 6

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Bolt Clearance

Depth (in) (E)

Overall

Length (in) (L)

Weight (lbs)

3/8 J7312HT 9/16 15/16 5/16 2-9/32 3-1/4 0.43

7/16 J7314HT 21/32 15/16 3/8 2-1/4 3-1/4 0.43

1/2 J7316HT 23/32 15/16 3/8 2-3/16 3-1/4 0.42

9/16 J7318HT 13/16 15/16 7/16 2-3/3 3-1/4 0.39

5/8 J7320HT 7/8 15/16 1/2 2-1/32 3-1/4 0.37

11/16 J7322HT 31/32 31/32 1/2 2 3-1/4 0.47

3/4 J7324HT 1-1/32 1-1/32 1-11/64 1-7/16 3-1/4 0.39

13/16 J7326HT 1-1/8 1-1/8 1-11/64 1-7/16 3-1/4 0.48

7/8 J7328HT 1-3/16 1-3/16 1-13/32 1-7/16 3-1/2 0.58

15/16 J7330HT 1-17/64 1-17/64 1-13/32 1-7/16 3-1/2 0.69

1 J7332HT 1-3/8 1-3/8 1-13/32 1-7/16 3-1/2 0.76

1-1/16 J7334HT 1-31/64 1-31/64 1-17/32 1-5/16 3-1/2 0.89

1-1/8 J7336HT 1-9/16 1-9/16 1-17/32 1-5/16 3-1/2 1.03

1-3/16 J7338HT 1-5/8 1-5/8 1-17/32 1-5/16 3-1/2 1.14

1-1/4 J7340HT 1-11/16 1-11/16 1-17/32 1-5/16 3-1/2 1.22

1-5/16 J7342HT 1-13/16 1-13/16 1-17/32 1-5/16 3-1/2 1.36

1-3/8 J7344HT 1-13/16 1-13/16 1-17/32 1 3-1/2 1.44

1-7/16 J7346HT 1-15/16 1-15/16 1-13/16 1 3-1/2 1.56

1-1/2 J7348HT 2 2 1-13/16 1 3-1/2 1.58

7 ASME B107.2

MM 6

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Bolt Clearance

Depth (in) (E)

Overall

Length (in) (L)

Weight (lbs)

10 J7310MHT 39/64 15/16 3/8 2-7/32 3-1/4 0.43

11 J7311MHT 21/32 15/16 25/64 2-13/64 3-1/4 0.44

12 J7312MHT 11/16 15/16 7/16 2-5/32 3-1/4 0.45

13 J7313MHT 47/64 15/16 7/16 2-5/32 3-1/4 0.41

14 J7314MHT 13/16 15/16 7/16 2-5/32 3-1/4 0.35

15 J7315MHT 27/32 15/16 17/32 2-1/16 3-1/4 0.37

16 J7316MHT 7/8 15/16 17/32 2-1/16 3-1/4 0.37

17 J7317MHT 15/16 15/16 11/16 1-29/32 3-1/4 0.35

18 J7318MHT 1 1 3/4 1-27/32 3-1/4 0.40

19 J7319MHT 1-1/32 1-1/32 1-5/32 1-7/16 3-1/4 0.37

20 J7320MHT 1-1/16 1-1/16 1-5/32 1-7/16 3-1/4 0.41

21 J7321MHT 1-1/8 1-1/8 1-13/32 1-27/64 3-1/2 0.51

22 J7322MHT 1-3/16 1-3/16 1-13/32 1-27/64 3-1/2 0.56

23 J7323MHT 1-1/4 1-1/4 1-13/32 1-27/64 3-1/2 0.63

24 J7324MHT 1-5/16 1-5/16 1-13/32 1-27/64 3-1/2 0.72

30 J7330MHT 1-25/32 1-25/32 2-35/64 1-27/64 3-1/2 1.45

7 ASME B107.33M


Impact Sockets







> > Large clearance holes, concentric opening and nut end chamfer make it easy

to position socket on fasteners.



> > Impact sockets are used wherever powered drive tools are used to install or

remove fasteners.

> > Impact sockets are designed to withstand higher torque and force associated

with impact tools in repetitive application.

> > Extra length provides easy access to fasteners in recesses or where nuts and

bolts protrude.





3/8 J7312S 3/4 7/8 11/32 2-19/32 3-1/4 0.37

7/16 J7314S 27/32 15/16 3/8 2-19/32 3-1/4 0.44

1/2 J7316S 51/16 15/16 7/16 2-19/32 3-1/4 0.43

9/16 J7318S 1-1/32 1-1/32 1/2 2-19/32 3-1/4 0.54

5/8 J7320S 1-1/8 1-1/8 1/2 2-19/32 3-1/4 0.63

11/16 J7322S 1-3/16 1-3/16 1-5/32 2-19/32 3-1/4 0.61

3/4 J7324S 1-5/16 1-5/16 1-5/32 2-19/32 3-1/4 0.76

13/16 J7326S 1-3/8 1-3/8 1-5/32 2-19/32 3-1/4 0.83

7/8 J7328S 1-1/2 1-1/2 1-13/32 2-27/32 3-1/2 1.10

15/16 J7330S 1-39/64 1-39/64 1-13/32 2-27/32 3-1/2 1.24

1 J7332S 1-11/16 1-11/16 1-13/32 2-27/32 3-1/2 1.54

7 ASME B107.2

thin wall impact sockets

When you need to fit an impact socket on a tightly spaced

fastener, don't reach for a thin wall hand socket.

The correct tool is a thin wall impact socket, made

from the same metal as standard impact sockets,

available in both fractional and metric sizes.

The thinner wall helps to fit over the fastener in

tight situations whereas the correct steel alloy will

keep you safe and your tool running correctly.


>

>

>

B

A

D

E

L

C






Made from the

same steel alloy

as standard

impact sockets,

but thinner.





1/2" Drive Universal Impact Sockets - 6 Point

> > Ball and spring design which allows for a 30°

working angle.





E

C

B







7/16 J74274P 3/4 1-1/16 1/2 3/4 2-19/32 0.34

1/2 J74275P 3/4 1-1/16 1/2 3/4 2-19/32 0.34

9/16 J74276P 27/32 1-1/16 1/2 3/4 2-19/32 0.36

5/8 J74277P 15/16 1-1/16 1/2 3/4 2-19/32 0.38

11/16 J74278P 1-1/16 1-1/4 1/2 3/4 2-19/32 0.56

3/4 J74279P 1-3/32 1-1/4 1/2 3/4 2-19/32 0.54

13/16 J74280P 1-3/16 1-1/4 1/2 3/4 2-19/32 0.56

7/8 J74281P 1-1/4 1-1/4 1/2 3/4 2-19/32 0.58

15/16 J74282P 1-5/16 1-3/8 1/2 3/4 2-27/32 0.69

1 J74283P 1-11/32 1-3/8 1/2 3/4 2-27/32 1.71

1-1/16 J74284P 1-13/32 1-3/8 9/16 13/16 2-15/16 1.72

1-1/8 J74285P 1-31/64 1-3/8 5/8 7/8 3-1/32 1.80

1-3/16 J74286P 1-9/16 1-3/8 11/16 57/64 3-3/32 1.83

1-1/4 J74287P 1-5/8 1-3/8 3/4 1-1/32 3-3/16 1.86

1-15/16 J74288P 1-45/64 1-3/8 13/16 1 3-9/32 1.86



13 J74413MP 25/32 1-1/16 1/2 3/4 2-5/8 0.34

14 J74414MP 55/64 1-1/16 1/2 3/4 2-5/8 0.39

15 J74415MP 57/64 1-1/16 1/2 3/4 2-5/8 0.43

16 J74416MP 61/64 1-1/16 1/2 3/4 2-5/8 0.48

17 J74417MP 1-1/64 1-1/4 1/2 3/4 2-5/8 0.53

18 J74418MP 1-1/16 1-1/4 1/2 3/4 2-5/8 0.54

19 J74419MP 1-7/64 1-1/4 1/2 3/4 2-5/8 0.54

21 J74421MP 1-13/64 1-1/4 1/2 3/4 2-5/8 0.54

22 J74422MP 1-1/4 1-1/4 1/2 3/4 2-5/8 0.58

24 J74424MP 1-21/64 1-1/4 1/2 3/4 2-5/8 0.58

D

L

7

7


Impact Sockets

1/2" Drive Deep Universal

Impact Sockets - 6 Point

BLACK OXIDE

> >


Ball and spring design which allows for a 30°

working angle.






Torx ® hex HEX


B


E

D

L

C







Overall

Product #

Length (in)

Weight (lbs)

J74470P 2-19/32 0.57

7 ASME B107.2


INCH 6


(in) (E)


1/2 J75275P 1-1/16 11/16 1-5/8 3-9/16 0.41

9/16 J75276P 1-1/16 11/16 1-5/8 3-9/16 0.43

5/8 J75277P 1-1/16 11/16 1-21/32 3-9/16 0.45

11/16 J75278P 1-1/4 11/16 1-21/32 3-1/2 0.50

3/4 J75279P 1-1/4 11/16 1-39/64 3-1/2 0.55

13/16 J75280P 1-1/4 11/16 1-5/8 3-1/2 0.61

7/8 J75281P 1-1/4 11/16 1-5/8 3-1/2 0.73

15/16 J75282P 1-3/8 11/16 1-43/64 3-23/32 0.80


MM 6


(in) (E)


13 J75413MP 1-1/16 11/16 1-5/8 3-1/2 0.43

14 J75414MP 1-1/16 11/16 1-5/8 3-1/2 0.45

15 J75415MP 1-1/16 11/16 1-5/8 3-1/2 0.50

16 J75416MP 1-1/16 11/16 1-5/8 3-1/2 0.55

17 J75417MP 1-1/4 11/16 1-5/8 3-1/2 0.61

18 J75418MP 1-1/4 11/16 1-5/8 3-1/2 0.73

19 J75419MP 1-1/4 11/16 1-5/8 3-1/2 0.80



>



7

7




1/2" Drive impact Torx ® , Hex bit Sockets & Adapters


> > Proto ® Torx ® Impact Sockets can be used on stubborn Torx ® fasteners.


> > Torx ® Impact Sockets are used wherever power drive tools are used to

help install or remove fasteners.

> > Torx ® Impact Sockets are designed to withstand the high torque and

force associated with impact tools in repetitive applications.



Torx ® Size

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Bolt Clearance

Depth (in) (E)

Overall


TORX ®

E14 J7414TX 11/16 7/8 7/16 27/32 1-1/2 0.14

E16 J7416TX 11/16 7/8 7/16 27/32 1-1/2 0.13

E18 J7418TX 27/32 7/8 17/32 27/32 1-1/2 0.14

E20 J7420TX 15/16 15/16 19/32 27/32 1-1/2 0.17




> > Hex bit impact sockets are used wherever powered drive tools are used





INCH

hex

Bit Overall


1/4 J74411/4 1-3/4 3-1/4 0.18

5/16 J74415/16 1-3/4 3-1/4 0.22

3/8 J74413/8 1-3/4 3-1/4 0.24

7/16 J74417/16 1-3/4 3-1/4 0.27

1/2 J74411/2 1-7/8 3-5/8 0.47

9/16 J74419/16 1-7/8 3-5/8 0.49

5/8 J74415/8 2 4 0.84

7

L

B

A

C

D

E

MM

hex

Bit Overall


6 J7441-6M 1-3/4 3-1/4 0.19

8 J7441-8M 1-3/4 3-1/4 0.21

10 J7441-10M 1-3/4 3-1/4 0.26

12 J7441-12M 1-3/4 3-1/4 0.29

14 J7441-14M 1-7/8 3-5/8 0.49

17 J7441-17M 2 4 0.88

7

7

1/2" Drive Adapters

>

>

>

> Use adapters to help increase or decrease drive end size.

> Do not use hand adapters with power tools.


large drive tools.



Product # INCH Overall Length (in) Weight (lbs)

J7650 3/8" F x 1/2" M 1-5/16 0.13

J7651 1/2" F x 3/8" M 1-7/16 0.12

J7652 1/2" F x 3/4" M 1-29/32 0.35

J7653 3/4" F x 1/2" M 2-1/16 0.48

J7655 5/8" F x 1/2" M 1-53/64 0.34

7



Impact Sockets


>

> Use extensions to gain access to fasteners in locations that would


> > Male square is oriented in-line with female squares for use with fixed



with drive tools.





Product #

Overall

Length (in)

Weight (lbs)

J7180P 2 0.19

J7182P 3 0.3

J7181P 5 0.47

J7184P 9 0.89

J7183-00 10 0.89

7 ASME B107.2

1/2" Drive Locking Extensions



> > Patented locking feature locks sockets to the extension with exceptional force.


1/2" Drive impact Extensions& Retaining Rings

Product # Overall Length (in) Weight (lbs)

J7503 3 0.34

J7505 5 0.57

J7510 10 1.04

7


> > Retaining Rings are used to help secure sockets onto drive tools.

> > They are not intended to bear any load.

> > The rotational forces are between the drive tool and the socket.

> > One-piece construction, no loose parts.



JRR50087 Retaining Ring, 1/2" DR 870 GRV 7/8 1 1/8 0.01

JRR50095 Retaining Ring, 1/2" DR 950 GRV 61/64 1-1/16 1/8 0.01






7


Torx ® hex HEX

BLACK OXIDE




3/4" Drive Impact Sockets





INCH 6 12

Nut End Outside Drive End Outside Nut Depth

Diameter (in) (B) Diameter (in) (C) (in) (D)

Bolt Clearance

Depth (in) (E)

Overall

Length (in) (L)

Weight

(lbs)





Crush Retaining

Ring

O-Ring

Retaining

Pin

9/16 J07509 J07509T 1 1-5/8 23/64 15/16 1-7/8 0.72 JRR07523 J07500R J07500P

5/8 J07510 J07510T 1-3/32 1-5/8 25/64 15/16 1-7/8 0.69 JRR07523 J07500R J07500P

11/16 J07511 J07511T 1-5/32 1-5/8 7/16 1 1-15/16 0.72 JRR07523 J07500R J07500P

3/4 J07512 J07512T 1-15/64 1-5/8 15/32 1 1-15/16 0.70 JRR07523 J07500R J07500P

13/16 J07513 J07513T 1-5/16 1-5/8 1/2 1 1-15/16 0.67 JRR07523 J07500R J07500P

7/8 J07514 J07514T 1-1/2 1-5/8 35/64 1-1/16 2 0.73 JRR07523 J07500R J07500P

15/16 J07515 J07515T 1-5/8 1-5/8 37/64 1-1/16 2 0.78 JRR07523 J07500R J07500P

1 J07516 J07516T 1-5/8 1-5/8 5/8 1-1/8 2-1/16 0.73 JRR07523 J07500R J07500P

1-1/16 J07517 J07517T 1-5/8 1-5/8 21/32 1-1/8 2-1/16 0.81 JRR07523 J07500R J07500P

1-1/8 J07518 J07518T 1-3/4 1-3/4 45/64 1-1/4 2-3/16 0.91 JRR07526 J07500R J07500P

1-3/16 J07519 J07519T 1-7/8 1-3/4 47/64 1-1/4 2-3/16 1.02 JRR07526 J07500R J07500P

1-1/4 J07520 J07520T 2 1-3/4 3/4 1-1/4 2-3/16 1.10 JRR07526 J07500R J07500P

1-5/16 J07521 J07521T 2-1/8 1-3/4 27/32 1-1/4 2-3/16 1.19 JRR07526 J07500R J07500P

1-3/8 J07522 J07522T 2-1/8 1-3/4 13/16 1-3/16 2-1/4 1.18 JRR07526 J07500R J07500P

1-7/16 J07523 J07523T 2-1/4 1-3/4 7/8 1-3/8 2-5/16 1.29 JRR07526 J07500R J07500P

1-1/2 J07524 J07524T 2-3/8 1-3/4 1 1-7/16 2-3/8 1.43 JRR07526 J07500R J07500P

1-9/16 J07525 J07525T 2-3/8 1-3/4 1 1-1/2 2-7/16 1.57 JRR07526 J07500R J07500P

1-5/8 J07526 J07526T 2-3/8 1-3/4 1 1-1/2 2-7/16 1.60 JRR07526 J07500R J07500P

1-11/16 J07527 J07527T 2-39/64 1-3/4 1-1/8 1-11/16 2-5/8 1.78 JRR07526 J07500R J07500P

1-3/4 J07528 J07528T 2-39/64 1-3/4 1-1/8 1-11/16 2-5/8 1.83 JRR07526 J07500R J07500P

1-13/16 J07529 J07529T 2-3/4 1-3/4 1-1/8 1-11/16 2-5/8 1.92 JRR07526 J07500R J07500P

1-7/8 J07530 J07530T 2-3/4 1-3/4 1-1/4 1-7/8 2-13/16 2.19 JRR07526 J07500R J07500P

1-15/16 J07531 J07531T 2-7/8 1-3/4 1-1/4 1-7/8 2-13/16 2.28 JRR07526 J07500R J07500P

2 J07532 J07532T 3 1-3/4 1-1/4 1-7/8 2-13/16 2.30 JRR07526 J07500R J07500P

2-1/16 J07533 J07533T 3 1-3/4 1-3/8 2-5/32 3-3/32 2.66 JRR07526 J07500R J07500P

2-1/8 J07534 J07534T 3-1/8 1-3/4 1-3/8 2-5/32 3-3/32 2.79 JRR07526 J07500R J07500P

2-3/16 J07535 J07535T 3-1/4 1-3/4 1-3/8 2-3/16 3-1/8 3.25 JRR07526 J07500R J07500P

2-1/4 J07536 J07536T 3-5/16 1-3/4 1-1/2 2-5/16 3-1/4 3.17 JRR07526 J07500R J07500P

2-5/16 J07537 – 3-9/32 1-3/4 1-1/2 1-15/16 3-5/16 3.21 JRR07526 J07500R J07500P

2-3/8 J07538 J07538T 3-1/2 1-3/4 1-1/2 2-7/16 3-3/8 3.45 JRR07526 J07500R J07500P

7 ASME B107.33M


Impact Sockets

3/4" Drive Metric Impact Sockets





MM 6 12



Bolt Clearance

Depth (in) (E)

Overall

Length (in) (L)

Weight

(lbs)





Crush Retaining

Ring

O-Ring

Retaining

Pin

17 J07517M J07517MT 1-5/32 1-5/8 27/64 63/64 1-59/64 0.68 JRR07523 J07500R J07500P

19 J07519M J07519MT 1-13/64 1-5/8 15/32 63/64 1-59/64 0.70 JRR07523 J07500R J07500P

20 J07520M J07520MT 1-19/64 1-5/8 9/16 63/64 1-59/64 0.70 JRR07523 J07500R J07500P

21 J07521M J07521MT 1-23/64 1-5/8 5/8 59/64 1-59/64 0.70 JRR07523 J07500R J07500P

22 J07522M J07522MT 1-27/64 1-5/8 11/16 1-1/16 2 0.79 JRR07523 J07500R J07500P

23 J07523M J07523MT 1-5/8 1-5/8 11/16 1-1/16 2 0.80 JRR07523 J07500R J07500P

24 J07524M J07524MT 1-5/8 1-5/8 19/32 1-1/16 2 0.73 JRR07523 J07500R J07500P

25 J07525M J07525MT 1-5/8 1-5/8 11/16 1-1/16 2 0.76 JRR07523 J07500R J07500P

26 J07526M J07526MT 1-5/8 1-5/8 3/4 1-1/8 2-1/16 0.77 JRR07523 J07500R J07500P

27 J07527M J07527MT 1-5/8 1-5/8 13/16 1-1/8 2-1/16 0.74 JRR07523 J07500R J07500P

28 J07528M J07528MT 1-5/8 1-5/8 45/64 1-1/8 2-1/16 0.72 JRR07523 J07500R J07500P

29 J07529M J07529MT 45.4 1-5/8 19.7 1-1/8 2-3/16 1.01 JRR07523 J07500R J07500P

30 J07530M J07530MT 1-7/8 1-3/4 59/64 1-7/32 2-3/16 1.01 JRR07526 J07500R J07500P

31 J07531M J07531MT 1-7/8 1-3/4 7/8 1-1/8 2-3/16 0.99 JRR07526 J07500R J07500P

32 J07532M J07532MT 2 1-3/4 7/8 1-9/64 2-3/16 1.13 JRR07526 J07500R J07500P

33 J07533M J07533MT 2 1-3/4 7/8 1-3/16 2-3/16 1.08 JRR07526 J07500R J07500P

34 J07534M J07534MT 2-1/8 1-3/4 15/16 1-3/16 2-1/4 1.18 JRR07526 J07500R J07500P

35 J07535M J07535MT 2-1/8 1-3/4 15/16 1-5/16 2-1/4 1.18 JRR07526 J07500R J07500P

36 J07536M J07536MT 2-1/4 1-3/4 15/16 1-9/32 2-5/16 1.32 JRR07526 J07500R J07500P

38 J07538M J07538MT 2-3/8 1-3/4 1 1-21/64 2-3/8 1.56 JRR07526 J07500R J07500P

40 J07540M J07540MT 2-1/2 1-3/4 1-1/32 1-17/64 2-1/2 1.64 JRR07526 J07500R J07500P

41 J07541M J07541MT 2-1/2 1-3/4 1-1/16 1-31/64 2-5/8 1.76 JRR07526 J07500R J07500P

42 J07542M J07542MT 2-1/2 1-3/4 1-1/8 1-45/64 2-3/4 1.87 JRR07526 J07500R J07500P

43 J07543M J07543MT 2-9/16 1-3/4 1-1/8 1-45/64 2-3/4 1.93 JRR07526 J07500R J07500P

46 J07546M J07546MT 2-3/4 1-3/4 1-1/4 1-45/64 2-7/8 2.10 JRR07526 J07500R J07500P

50 J07550M J07550MT 2-15/16 1-3/4 1-1/4 1-49/64 3-1/8 2.44 JRR07526 J07500R J07500P

7 ASME B107.33M



Torx ® hex HEX

BLACK OXIDE










> > Large clearance holes, concentric opening and nut end

chamfer make it easy to position socket on fasteners.

> > Made from high-strength steel to help minimize

wall thickness and provide access to fasteners in

recesses and where nuts and bolts protrude.

> > Impact sockets are designed to withstand higher torque and



Ring or pin and o-ring to help secure the socket to the drive tool anvil.







Nut End Outside Drive End Outside Nut Depth Bolt Clearance Overall Weight Crush Retaining

Retaining

INCH 8 Diameter (in) (B) Diameter (in) (C) (in) (D) Depth (in) (E) Length (in) (L) (lbs) Ring O-Ring Pin

3/4 J07512S 1-5/8 1-5/8 15/37 31/32 1-15/16 0.81 JRR07523 J07500R J07500P

13/16 J07513S 1-5/8 1-5/8 1/2 1-1/32 2 0.82 JRR07523 J07500R J07500P

7/8 J07514S 1-3/4 1-3/4 35/64 1-1/32 2 0.97 JRR07523 J07500R J07500P

15/16 J07515S 1-13/16 1-3/4 19/32 1-3/32 2-1/16 1.07 JRR07523 J07500R J07500P

1 J07516S 2 1-3/4 5/8 1-5/32 2-1/8 1.23 JRR07523 J07500R J07500P

1-1/16 J07517S 2-1/8 1-3/4 21/32 1-7/32 2-3/16 1.28 JRR07523 J07500R J07500P

1-1/8 J07518S 2-1/4 1-3/4 45/64 1-15/64 2-1/4 1.42 JRR07526 J07500R J07500P

1-3/16 J07519S 2-3/8 1-3/4 3/4 1-11/32 2-5/16 1.55 JRR07526 J07500R J07500P

1-1/4 J07520S 2-3/8 1-3/4 3/4 1-13/32 2-3/8 1.57 JRR07526 J07500R J07500P

1-5/16 J07521S 2-1/2 1-3/4 7/8 1-13/32 2-3/8 1.75 JRR07526 J07500R J07500P

7 ASME B107.33M









> > Impact sockets are used where ever powered drive tools are used to

install or remove fasteners.

> > Impact sockets are designed to withstand the high torque and force



Ring or pin and o-ring to help secure the socket to the drive tool anvil.




Retaining


5/8 J07510SS 1-1/4 1-5/8 25/64 15/16 2 0.70 JRR07523 J07500R J07500P

11/16 J07511SS 1-11/32 1-5/8 7/16 15/16 1-7/8 0.75 JRR07523 J07500R J07500P

13/16 J07513SS 1-5/8 1-5/8 33/64 1-1/16 2 0.82 JRR07523 J07500R J07500P

7 ASME B107.2


Impact Sockets

3/4" Drive Deep Impact Sockets






L

B

A

C

D

E






INCH 6 Diameter (in) (B) Diameter (in) (C) (in) (D) Depth (in) (E) Length (in) (L) (lbs) Ring O-Ring Retaining Pin

9/16 J07509L 1 1-5/8 15/32 2-5/16 3-1/4 1.34 JRR07523 J07500R J07500P

5/8 J07510L 1-3/32 1-5/8 33/64 2-5/16 3-1/4 1.28 JRR07523 J07500R J07500P

11/16 J07511L 1-5/32 1-5/8 9/16 2-5/16 3-1/4 1.34 JRR07523 J07500R J07500P

3/4 J07512L 1-1/4 1-5/8 39/64 2-5/16 3-1/4 1.35 JRR07523 J07500R J07500P

13/16 J07513L 1-5/16 1-5/8 43/64 2-5/16 3-1/4 1.18 JRR07523 J07500R J07500P

7/8 J07514L 1-1/2 1-5/8 23/32 2-5/16 3-1/4 1.23 JRR07523 J07500R J07500P

15/16 J07515L 1-5/8 1-5/8 25/32 2-5/16 3-1/4 1.20 JRR07523 J07500R J07500P

1 J07516L 1-5/8 1-5/8 53/64 2-5/16 3-1/4 1.11 JRR07523 J07500R J07500P

1-1/16 J07517L 1-5/8 1-5/8 7/8 2-5/16 3-1/4 1.20 JRR07523 J07500R J07500P

1-1/8 J07518L 1-3/4 1-3/4 59/64 2-5/16 3-1/4 1.29 JRR07526 J07500R J07500P

1-3/16 J07519L 1-7/8 1-3/4 31/32 2-5/16 3-1/4 1.54 JRR07526 J07500R J07500P

1-1/4 J07520L 2 1-3/4 1 2-5/16 3-1/4 1.89 JRR07526 J07500R J07500P

1-5/16 J07521L 2-1/8 1-3/4 1 2-5/16 3-1/4 1.88 JRR07526 J07500R J07500P

1-3/8 J07522L 2-1/8 1-3/4 1 2-5/16 3-1/4 1.79 JRR07526 J07500R J07500P

1-7/16 J07523L 2-1/4 1-3/4 1-1/16 2-7/16 3-1/2 2.00 JRR07526 J07500R J07500P

1-1/2 J07524L 2-3/8 1-3/4 1-1/16 2-7/16 3-1/2 2.25 JRR07526 J07500R J07500P

1-9/16 J07525L 2-3/8 1-3/4 1 2-3/8 3-13/16 2.43 JRR07526 J07500R J07500P

1-5/8 J07526L 2-3/8 1-3/4 2-1/4 2-5/8 3-13/16 2.57 JRR07526 J07500R J07500P

1-11/16 J07527L 2-39/64 1-3/4 2-1/4 2-5/8 3-7/8 2.69 JRR07526 J07500R J07500P

1-3/4 J07528L 2-39/64 1-3/4 2-1/4 2-5/8 3-7/8 2.84 JRR07526 J07500R J07500P

1-13/16 J07529L 2-3/4 1-3/4 2-1/4 2-5/8 3-7/8 3.09 JRR07526 J07500R J07500P

1-7/8 J07530L 2-3/4 1-3/4 2-3/8 3-3/4 4-1/16 3.19 JRR07526 J07500R J07500P

2 J07532L 3 1-3/4 1-1/2 2-3/4 4-1/16 3.45 JRR07526 J07500R J07500P

7 ASME B107.2



Retaining

Diameter (in) (B) Diameter (in) (C) (in) (D) Depth (in) (E) Length (in) (L) (lbs) Ring O-Ring Pin

19 J07519ML J07519MLT 1-7/32 1-5/8 5/8 2-1/4 3-1/4 1.32 JRR07523 J07500R J07500P

21 J07521ML J07521MLT 1-3/8 1-5/8 51/64 2-1/4 3-1/4 1.30 JRR07523 J07500R J07500P

22 J07522ML J07522MLT 1-7/16 1-5/8 13/16 2-1/4 3-1/4 1.20 JRR07523 J07500R J07500P

23 J07523ML J07523MLT 1-5/8 1-5/8 3/4 2-1/4 3-1/4 1.28 JRR07523 J07500R J07500P

24 J07524ML J07524MLT 1-5/8 1-5/8 13/16 2-1/4 3-1/4 1.31 JRR07523 J07500R J07500P

26 J07526ML J07526MLT 1-5/8 1-5/8 27/32 2-1/4 3-1/4 1.20 JRR07523 J07500R J07500P

27 J07527ML J07527MLT 1-5/8 1-5/8 7/8 2-1/4 3-1/4 1.14 JRR07523 J07500R J07500P

30 J07530ML J07530MLT 1-7/8 1-3/4 31/32 2-9/32 3-1/4 1.45 JRR07526 J07500R J07500P

32 J07532ML J07532MLT 2 1-3/4 1 2-9/32 3-1/4 1.63 JRR07526 J07500R J07500P

33 J07533ML J07533MLT 2 1-3/4 1 2-9/32 3-1/4 1.55 JRR07526 J07500R J07500P

35 J07535ML J07535MLT 2-1/8 1-3/4 1 2-9/32 3-1/4 1.89 JRR07526 J07500R J07500P

36 J07536ML J07536MLT 2-1/4 1-3/4 1 2-9/32 3-1/4 1.91 JRR07526 J07500R J07500P

38 J07538ML J07538MLT 2-3/8 1-3/4 1-1/16 2-29/64 3-1/2 2.10 JRR07526 J07500R J07500P

41 J07541ML J07541MLT 2-1/2 1-3/4 1-1/16 2-29/64 3-1/2 2.36 JRR07526 J07500R J07500P

43 J07543ML J07543MLT 2-9/16 1-3/4 1-1/8 2-29/64 3-1/2 2.52 JRR07526 J07500R J07500P

7 ASME B107.33M

MM 6 12


Torx ® hex HEX

BLACK OXIDE
















INCH 4

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Bolt Clearance

Depth (in) (E)

Overall

Length (in) (L)

Weight (lbs)

13/16 J07513SL 1-5/8 1-5/8 43/64 3-1/16 4 1.75

7 ASME B107.2

L

B

A

C

D

E






B

A





D

L

E

C

INCH 6

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Bolt Clearance

Depth (in) (E)

Overall

Length (in) (L)

Weight

(lbs)

Crush Retaining

Ring

O-Ring

Retaining

Pin

3/4 J07512-LT 1-3/8 1-3/8 39/64 3-1/16 4 1.04 JRR07520 J07500R J07500P

13/16 J07513-LT 1-3/8 1-3/8 21/32 3-1/16 4 1.02 JRR07520 J07500R J07500P

7/8 J07514-LT 1-3/8 1-3/8 23/32 3-1/16 4 1.01 JRR07520 J07500R J07500P

15/16 J07515-LT 1-3/8 1-3/8 49/64 3-1/16 4 0.80 JRR07520 J07500R J07500P

1 J07516-LT 1-7/16 1-7/16 53/64 3-1/16 4 1.06 JRR07520 J07500R J07500P

1-1/16 J07517-LT 1-1/2 1-1/2 7/8 3-1/16 4 0.96 JRR07523 J07500R J07500P

1-1/8 J07518-LT 1-5/8 1-5/8 59/64 3-1/16 4 1.19 JRR07526 J07500R J07500P

1-3/16 J07519-LT 1-11/16 1-11/16 31/32 3-1/16 4 1.24 JRR07526 J07500R J07500P

1-1/4 J07520-LT 1-3/4 1-3/4 1 3-1/16 4 1.33 JRR07526 J07500R J07500P

1-5/16 J07521-LT 1-7/8 1-3/4 1-1/8 2-5/16 3-1/4 1.28 JRR07526 J07500R J07500P

1-3/8 J07522-LT 1-15/16 1-3/4 1-1/8 2-5/16 3-1/4 1.32 JRR07526 J07500R J07500P

1-7/16 J07523-LT 2 1-3/4 1-1/8 2-9/16 3-1/2 1.42 JRR07526 J07500R J07500P

1-1/2 J07524-LT 2-1/8 1-3/4 1-1/4 2-9/16 3-1/2 1.86 JRR07526 J07500R J07500P

7 ASME B107.2


Impact Sockets

3/4" Drive Budd Wheel Deep Socket



Nut End Outside Diameter Drive End Outside Diameter Overall

INCH 6

(in) (B)

(in) (C)

Length (in) (L)

Weight (lbs)

1-1/2 J07524-LS 2-1/4 1-5/8 4 3.12




> > Used wherever powered drive tools are used to install or remove fasteners.









Overall

Product #

Length (in)

Weight (lbs)

J07570A 3-1/2 1.40

7

ABOUT Universal Impact Joints

A universal impact joint is handy for

reaching into difficult spots. Never

use a universal joint designed for

a hand tool on an impact gun.

Safety Ring Hole.

Always use an impact universal

joint on an impact gun. They are

made from the same forgiving

alloy steel as standard impact

sockets, and they have the same

standard safety features.

30° Working Angle.

Ball & Spring Joint.

Thick Collar to

Protect Joint.

Groove and Hole for

Second Safety Ring.


Torx ® hex HEX

BLACK OXIDE



3/4" Drive impact Adaoters & extensions

3/4" Drive Adapters



>


large drive tools.



Overall

Product #

INCH Length (in) Weight (lbs)

J07655 3/4" F x 1" M 2-1/2 0.89

J07656 1" F x 3/4" M 2-7/8 1.42

J7656 5/8" F x 3/4" M 1-31/32 0.40

7 ASME B107.2


>

> Use extensions to gain access to fasteners in locations that would





with drive tools.



> > Features two thru holes and a groove to accept a Proto retaining ring or

pin or o-ring to help secure extension to the drive tool anvil.

Product #

Overall

Length (in)

Weight (lbs)

J07565 5 1.48

J07567 7 1.97

J07568 10 2.73

J07569 13 3.12

7 ASME B107.2




INCH

hex

Overall Weight Repair

Length (in) (lbs) Kit Part #

9/16 J075909/16 3-3/4 0.96 J075909/16RK

5/8 J075905/8 3-27/32 1.11 J075905/8RK

3/4 J075903/4 4-3/8 1.75 J075903/4RK

7/8 J075907/8 4-3/4 2.09 J075907/8RK

1 J075901 5-13/64 2.59 J05901RK

7

3/4" Drive Hex Bit Repair Kits

INCH

hex

Weight (lbs)

9/16 J075909/16RK 0.18

5/8 J075905/8RK 0.21

3/4 J075903/4RK 0.41

7/8 J075907/8RK 0.62

1 J075901RK 0.94

7


Impact Sockets

3/4" Drive Impact Socket O-Ring


> > For use with all 3/4” drive impact sockets and attachments.

Product #

Weight (lbs)

J07500R 0.01

3/4" Drive Impact Socket Retaining Pin


> > For use with all 3/4” drive impact sockets and attachments.

Product #

Weight (lbs)

J07500P 0.01

7

7

3/4" Drive impact Retaining Pin & Rings


> > Retaining rings are used to help secure sockets onto drive tools.

> > They are not intended to bear any load.

> > The rotational forces are between the drive tool and the socket.

> > The resin crush gauge on the pin helps indicate when a socket is

excessively worn and should be replaced.

> > Drive tool and socket should line up when in use and should not pinch the

crush gauge.

> > Cracked sockets and/or worn drive tools cause each other to turn

excessively in relation to each other. This action pinches the small

fin or the crush gauge on these retaining rings. If the crush gauge is

pinched, it is an indication that the socket and or the drive tool need to

be replaced.

> > One-piece construction, no loose parts. Pin is made of resin which

allows the material to compress without breaking.

> > Part numbers are embossed on the rings near the point at which the pin

and ring meet.

Product # For Groove Dia. (in) Diameter (in) Height (in) Weight (lbs)

JRR07520 1-1/4 1-7/16 3/16 0.01

JRR07523 1-7/16 1-5/8 3/16 0.01

JRR07526 1-5/8 1-13/16 3/16 0.01

JRR07528 1-3/4 1-15/16 3/16 0.01

JRR07532 1-15/16 2-3/16 3/16 0.01

JRR07534 2-1/8 2-5/16 3/16 0.01

JRR07536 2-1/4 2-7/16 3/16 0.01


Torx ® hex HEX

BLACK OXIDE



1" Drive impact Sockets

1" Drive Impact Sockets






INCH 6 12

L

B

A

C



D

E

Bolt Clearance

Depth (in) (E)

Overall Weight

Length (in) (L) (lbs)




Crush Retaining

Ring


O-Ring

Retaining

Pin

3/4 J10012 J10012T 1-7/16 2-1/8 19/32 1-5/16 2-7/16 1.11 JRR10028 J10000R1 J10000P1

13/16 J10013 – 1-1/2 2-1/8 5/8 1-3/8 2-1/2 1.07 JRR10028 J10000R1 J10000P1

7/8 J10014 J10014T 1-17/32 2-1/8 21/32 1-3/8 2-1/2 1.17 JRR10028 J10000R1 J10000P1

15/16 J10015 J10015T 1-39/64 2-1/8 19/32 1-3/8 2-1/2 1.19 JRR10028 J10000R1 J10000P1

1 J10016 J10016T 1-3/4 2-1/8 3/4 1-3/8 2-1/2 1.19 JRR10028 J10000R1 J10000P1

1-1/16 J10017 J10017T 1-3/4 2-1/8 7/8 1-1/2 2-5/8 1.28 JRR10028 J10000R1 J10000P1

1-1/8 J10018 J10018T 1-13/16 2-1/8 7/8 1-1/2 2-5/8 1.27 JRR10028 J10000R1 J10000P1

1-3/16 J10019 – 1-7/8 2-1/8 7/8 1-1/2 2-5/8 1.50 JRR10028 J10000R1 J10000P1

1-1/4 J10020 J10020T 2-1/8 2-1/8 15/16 1-1/2 2-5/8 1.50 JRR10028 J10000R1 J10000P1

1-5/16 J10021 J10021T 2-1/8 2-1/8 15/16 1-5/8 2-3/4 1.45 JRR10028 J10000R1 J10000P1

1-3/8 J10022 J10022T 2-1/8 2-1/8 1-1/32 1-5/8 2-3/4 1.65 JRR10028 J10000R1 J10000P1

1-7/16 J10023 J10023T 2-1/8 2-1/8 1-1/32 1-5/16 2-7/16 1.71 JRR10028 J10000R1 J10000P1

1-1/2 J10024 J10024T 2-3/8 2-3/8 1-1/4 1-1/2 2-5/8 1.89 JRR10028 J10000R1 J10000P1

1-9/16 J10025 – 2-3/8 2-3/8 1-1/4 1-1/2 2-5/8 2.14 JRR10032 J10000R2 J10000P2

1-5/8 J10026 J10026T 2-15/32 2-3/8 1-1/4 1-1/2 2-5/8 2.11 JRR10032 J10000R2 J10000P2

1-11/16 J10027 J10027T 2-39/64 2-3/8 1-1/8 1-11/16 2-13/16 2.18 JRR10032 J10000R2 J10000P2

1-3/4 J10028 J10028T 2-11/16 2-3/8 1-1/8 1-11/16 2-13/16 2.63 JRR10034 J10000R2 J10000P2

1-13/16 J10029 – 2-51/64 2-3/8 1-1/8 1-1/16 2-13/16 2.55 JRR10034 J10000R2 J10000P2

1-7/8 J10030 J10030T 2-51/64 2-3/8 1-1/4 1-7/8 3 2.75 JRR10034 J10000R2 J10000P2

1-15/16 J10031 – 2-7/8 2-3/8 1-1/4 1-7/8 3 3.01 JRR10034 J10000R2 J10000P2

2 J10032 J10032T 3 2-3/8 1-1/4 1-7/8 3 3.10 JRR10034 J10000R2 J10000P2

2-1/16 J10033 J10033T 3 2-3/8 1-9/16 1-9/16 3-3/32 3.04 JRR10034 J10000R2 J10000P2

2-1/8 J10034 – 3-1/8 2-3/8 1-3/8 1-9/16 3-3/32 3.30 JRR10034 J10000R2 J10000P2

2-3/16 J10035 – 3-1/4 2-3/8 1-3/8 1-9/16 3-1/8 3.54 JRR10034 J10000R2 J10000P2

2-1/4 J10036 J10036T 3-5/16 2-3/8 1-1/2 1-21/32 3-1/4 3.60 JRR10034 J10000R2 J10000P2

2-5/16 J10037 – 3-7/16 2-3/8 1-1/2 1-23/32 3-21/64 4.13 JRR10034 J10000R2 J10000P2

2-3/8 J10038 J10038T 3-1/2 2-3/8 1-1/2 1-3/4 3-3/8 4.07 JRR10034 J10000R2 J10000P2

2-7/16 J10039 – 3-1/2 2-3/8 1-5/8 1-3/4 3-25/64 4.12 JRR10034 J10000R2 J10000P2

2-1/2 J10040 – 3-5/8 2-3/8 1 -5/8 1-13/16 3-1/2 4.15 JRR10034 J10000R2 J10000P2

2-9/16 J10041 – 3-47/64 2-3/8 1-5/8 1-13/16 3-1/2 4.94 JRR10040 - -

2-5/8 J10042 – 3-3/4 2-3/8 1-3/4 1-15/16 3-5/8 4.92 JRR10040 - -

2-11/16 J10043 – 3-7/8 2-3/8 1-3/4 1-15/16 3-21/32 5.39 JRR10040 - -

2-3/4 J10044 – 3-7/8 2-3/8 1-3/4 2 3-3/4 5.39 JRR10040 - -

2-13/16 J10045 – 4 2-3/8 1-7/8 2-3/64 3-13/16 5.99 JRR10040 - -

2-7/8 J10046 – 4-1/16 2-3/8 1-7/8 2-5/64 3-7/8 5.95 JRR10040 - -

2-15/16 J10047 – 4-1/8 2-3/8 1-7/8 2-1/16 3-7/8 6.11 JRR10040 - -

3 J10048 – 4-1/4 2-3/8 2 2-3/16 4 6.77 JRR10040 - -

3-1/8 J10050 – 4-3/8 2-3/8 2 2-3/16 4-1/16 6.94 JRR10040 - -

3-1/4 J10052 – 4-1/2 2-3/8 2 2-15/32 4-3/8 7.62 JRR10040 - -

3-3/8 J10054 – 4-9/16 2-3/8 2-1/4 2-15/32 4-7/16 7.80 JRR10040 - -

3-1/2 J10056 – 4-3/4 2-3/8 2-1/4 2-1/2 4-1/2 8.45 JRR10040 - -

3-5/8 J10058 – 4-7/8 2-3/8 2-1/4 2-35/64 4-3/4 10.59 - - -

3-7/8 J10062 – 5-1/16 2-3/8 2-1/4 2-31/32 5 12.20 - - -

4 J10064 – 5-3/4 2-3/8 2-1/2 4-3/8 5-1/2 14.89 - - -

4-1/8 J10066 – 6 2-3/8 2-3/4 4-5/8 5-1/2 15.26 - - -

4-1/4 J10068 – 6 2-3/8 2-3/4 4-5/8 5-1/2 15.56 - - -

4-1/2 J10072 – 6-1/4 2-3/8 3 4-7/8 6 17.61 - - -

7 ASME B107.2


Impact Sockets

MM 6

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Bolt Clearance

Depth (in) (E)

Overall Weight


Crush Retaining

Ring

O-Ring

Retaining

Pin

19 J10019M 1-7/16 2-1/8 39/64 57/64 2-13/32 1.10 JRR10028 J10000R1 J10000P1

22 J10022M 1-35/64 2-1/8 21/32 1 2-13/32 1.09 JRR10028 J10000R1 J10000P1

24 J10024M 1-39/64 2-1/8 3/4 1 2-13/32 1.06 JRR10028 J10000R1 J10000P1

26 J10026M 1-45/64 2 1-1/8 1-1/2 2-3/8 1.16 JRR10032 J10000R2 J10000P2

27 J10027M 1-49/64 2-1/8 7/8 1-13/64 2-19/32 1.27 JRR10032 J10000R2 J10000P2

28 J10028M 1-13/16 2-1/8 7/8 1-13/64 2-19/32 1.27 JRR10034 J10000R2 J10000P2

29 J10029M 1-51/64 2-1/8 1-19/64 1-31/64 2-19/32 1.30 JRR10034 J10000R2 J10000P2

30 J10030M 1-7/8 2-1/8 7/8 1-13/64 2-19/32 1.58 JRR10034 J10000R2 J10000P2

32 J10032M 2-1/8 2-1/8 15/16 1-13/64 2-19/32 1.51 JRR10034 J10000R2 J10000P2

33 J10033M 2-1/8 2-1/8 1 1-1/4 2-3/4 1.48 JRR10034 J10000R2 J10000P2

35 J10035M 2-13/64 2-1/8 1-13/32 1-13/64 2-45/64 1.63 JRR10034 J10000R2 J10000P2

36 J10036M 2-1/4 2-1/8 27/32 1-13/64 2-7/16 1.73 JRR10034 J10000R2 J10000P2

38 J10038M 2-25/64 2-25/64 1-13/32 1-1/4 2-45/64 1.91 JRR10034 J10000R2 J10000P2

41 J10041M 2-31/64 2-13/32 1-1/8 1-1/4 2-13/16 2.07 JRR10034 J10000R2 J10000P2

46 J10046M 2-25/32 2-13/32 1-5/16 1-13/32 2-13/16 2.63 JRR10040 - -

50 J10050M 3 2-13/32 1-7/16 1-1/2 3 3.20 JRR10040 - -

54 J10054M 3-3/32 2-13/32 1-19/32 1-1/2 3 3.33 JRR10040 - -

55 J10055M 3-1/4 2-13/32 1-9/16 1-9/16 3-1/8 3.71 JRR10040 - -

58 J10058M 3-1/2 2-7/16 1-43/64 2-13/32 3-13/64 3.85 - - -

60 J10060M 3-3/4 2-13/32 1-9/16 1-53/64 3-3/8 3.91 - - -

63 J10063M 3-3/4 2-13/32 1-9/16 1-13/16 3-3/8 4.12 - - -

65 J10065M 3-3/4 2-13/32 1-9/16 1-13/16 3-1/2 4.93 - - -

67 J10067M 3-3/4 2-3/4 2 2-21/64 3-1/2 4.93 - - -

70 J10070M 3-13/16 2-3/4 1-25/32 2-1/4 3-53/64 5.02 - - -

75 J10075M 4 2-3/4 2-13/64 2-11/16 3-27/32 6.15 - - -

80 J10080M 4-13/64 2-3/4 2-21/64 2-13/16 4 6.59 - - -

7 ASME B107.33M



Torx ® hex HEX

BLACK OXIDE




1" Drive Impact Sockets - 8 Point

>

> Drive end chamfer and four detents help provide quick positive engagement














Retaining


7/8 J10014S 2 2 5/8 1-3/8 2-5/8 1.33 JRR10028 J10000R1 J10000P1

15/16 J10015S 2 2 5/8 1-3/8 2-5/8 1.52 JRR10028 J10000R1 J10000P1

1 J10016S 2-3/32 2-3/32 11/16 1-3/8 2-13/16 1.61 JRR10028 J10000R1 J10000P1

1-1/8 J10018S 2-7/16 2-7/16 23/32 1-3/8 2-13/16 1.85 JRR10028 J10000R1 J10000P1

1-3/16 J10019S 2-1/4 2-3/32 23/32 1-3/8 2-11/16 1.74 JRR10028 J10000R1 J10000P1

1-1/4 J10020S 2-7/16 2-7/16 11/16 1-1/2 2-13/16 1.92 JRR10028 J10000R1 J10000P1

1-5/16 J10021S 2-1/2 2-1/2 25/32 1-1/2 2-13/16 2.07 JRR10028 J10000R1 J10000P1

1-3/8 J10022S 2-1/2 2-1/2 25/32 1-5/8 2-13/16 1.97 JRR10028 J10000R1 J10000P1

1-7/16 J10023S 2-13/16 2-13/16 13/16 1-5/8 2-15/16 2.54 JRR10028 J10000R1 J10000P1

1-1/2 J10024S 2-13/16 2-13/16 13/16 1-5/8 2-13/16 2.47 JRR10028 J10000R1 J10000P1

1-5/8 J10026S 3-3/32 3-3/32 13/16 1-5/8 3-1/2 3.81 JRR10032 J10000R2 J10000P2

1-11/16 J10027S 3-3/16 3-3/16 7/8 1-3/4 3-1/2 4.06 JRR10032 J10000R2 J10000P2

1-3/4 J10028S 3-3/16 3-3/16 7/8 1-3/4 3-1/2 4.29 JRR10034 J10000R2 J10000P2

1-13/16 J10029S 3-3/8 3-3/8 7/8 1-7/8 3-1/2 4.16 JRR10034 J10000R2 J10000P2

1-7/8 J10030S 3-13/32 3-13/32 15/16 1-7/8 3-1/2 4.17 JRR10034 J10000R2 J10000P2

2 J10032S 3-1/2 3-1/2 1 1-15/16 3-1/2 4.42 JRR10034 J10000R2 J10000P2

2-3/16 J10035S 3-7/8 3-7/8 1 1-15/16 3-1/2 5.28 JRR10034 J10000R2 J10000P2

7

1" Drive Impact Sockets - 4 Point















Retaining


3/4 J10012SS 1-7/8 2-1/8 5/8 1-3/8 2-1/2 1.57 JRR10028 J10000R1 J10000P

13/16 J10013SS 1-15/16 2-1/8 5/8 1-3/8 2-1/2 1.53 JRR10028 J10000R1 J10000P

7/8 J10014SS 2 2-1/8 5/8 1-3/8 2-1/2 1.52 JRR10028 J10000R1 J10000P

15/16 J10015SS 2-1/16 2-1/8 19/32 1-3/8 2-1/2 1.80 JRR10028 J10000R1 J10000P

1 J10016SS 2-1/8 2-1/8 11/16 1-3/8 2-1/2 1.75 JRR10028 J10000R1 J10000P

1-1/8 J10018SS 2-1/4 2-3/8 23/32 1-3/8 2-1/2 1.80 JRR10028 J10000R1 J10000P

1-1/2 J10024SS 2-5/8 2-5/8 25/32 1-3/8 2-1/2 2.80 JRR10028 J10000R1 J10000P

7


Impact Sockets

NEW 1" DRIVE IMPACT TOOLS

Up To 2500 ft-lbs of breakaway torque

1" drive Inline air impact wrenches

Available with two-stage triggers for precision control,

optional outside trigger and fingertip controls.

Extended

Anvil.

Flush

Anvil.


MASSIVE TORQUE WITH EXCELLENT POWER TO WEIGHT Ratio

1" DRIVE PISTOL GRIP IMPACT WRENCHES

Also driving up to 2500 ft-lbs of torque, adjustable

side handle, suspension hanger and fingertip

forward/reverse controls.

See page 456 for details.

Extended

Anvil.

Flush

Anvil.

See page 457 for details.

ALSO AVAILABLE

#5 spline end drive Impact Wrenches

Inline.

Pistol.


Torx ® hex HEX

BLACK OXIDE




1" Drive Deep Impact Sockets - 6 Point






INCH 6

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Bolt Clearance

Depth (in) (E)

Overall Weight






Crush Retaining

Ring

O-Ring

Retaining

Pin

3/4 J10012L 1-7/16 2 7/16 2-39/64 4 1.65 - - -

13/16 J10013L 1-7/16 2 29/64 2-39/64 4 1.65 - - -

7/8 J10014L 1-35/64 2-1/8 1/2 2-5/8 3-3/4 2.45 JRR10028 J10000R1 J10000P1

15/16 J10015L 1-39/64 2-1/8 1/2 2-5/8 3-3/4 2.64 JRR10028 J10000R1 J10000P1

1 J10016L 1-3/4 2-1/8 25/64 2-5/8 3-3/4 2.66 JRR10028 J10000R1 J10000P1

1-1/16 J10017L 1-3/4 2-1/8 5/8 2-5/8 3-3/4 2.54 JRR10028 J10000R1 J10000P1

1-1/8 J10018L 1-13/16 2-1/8 21/32 2-5/8 3-3/4 2.53 JRR10028 J10000R1 J10000P1

1-3/16 J10019L 1-7/8 2-1/8 21/32 2-5/8 3-3/4 2.32 JRR10028 J10000R1 J10000P1

1-1/4 J10020L 2-1/8 2-1/8 3/4 2-5/8 3-3/4 2.55 JRR10028 J10000R1 J10000P1

1-5/16 J10021L 2-1/8 2-1/8 49/64 2-5/8 3-3/4 2.45 JRR10028 J10000R1 J10000P1

1-3/8 J10022L 2-1/8 2-1/8 25/32 2-5/8 3-3/4 2.38 JRR10028 J10000R1 J10000P1

1-7/16 J10023L 2-1/8 2-1/8 7/8 2-5/32 4 2.52 JRR10028 J10000R1 J10000P1

1-1/2 J10024L 2-3/8 2-3/8 55/64 2-5/32 4 2.80 JRR10028 J10000R1 J10000P1

1-9/16 J10025L 2-3/8 2-3/8 55/64 2-3/8 4 2.89 JRR10028 J10000R1 J10000P1

1-5/8 J10026L 2-3/8 2-3/8 1 2-53/64 4 2.73 JRR10032 J10000R2 J10000P2

1-11/16 J10027L 2-39/64 2-3/8 1 2-53/64 4-1/16 3.45 JRR10032 J10000R2 J10000P2

1-3/4 J10028L 2-39/64 2-3/8 1-3/32 2-53/64 4-1/16 3.31 JRR10034 J10000R2 J10000P2

1-13/16 J10029L 2-3/4 2-3/8 1-1/8 2-53/64 4-1/16 3.65 JRR10034 J10000R2 J10000P2

1-7/8 J10030L 2-3/4 2-3/8 1-1/8 2-3/4 4-1/4 3.74 JRR10034 J10000R2 J10000P2

1-15/16 J10031L 2-7/8 2-3/8 1-1/8 2-3/4 4-1/4 4.05 JRR10034 J10000R2 J10000P2

2 J10032L 3 2-3/8 1-7/32 2-3/4 4-1/4 4.31 JRR10034 J10000R2 J10000P2

2-1/16 J10033L 3-1/8 2-3/8 1-7/32 2-3/4 4-1/4 4.52 JRR10034 J10000R2 J10000P2

2-1/8 J10034L 3-1/8 2-3/8 1-7/32 2-31/32 4-1/2 4.78 JRR10034 J10000R2 J10000P2

2-3/16 J10035L 3-1/4 2-3/8 1-3/8 2-15/16 4-1/2 5.19 JRR10034 J10000R2 J10000P2

2-1/4 J10036L 3-1/4 2-3/8 1-3/8 2-29/32 4-1/2 4.98 JRR10034 J10000R2 J10000P2

2-5/16 J10037L 3-1/2 2-3/8 1-3/8 2-29/32 4-3/4 5.92 JRR10034 J10000R2 J10000P2

2-3/8 J10038L 3-1/2 2-3/8 1-3/8 3-1/8 4-3/4 8.06 JRR10034 J10000R2 J10000P2

2-7/16 J10039L 3-9/16 2-3/8 1-3/8 3-3/16 4-7/8 5.82 JRR10034 J10000R2 J10000P2

2-1/2 J10040L 3-5/8 2-3/8 1-3/8 3-1/4 4-7/8 6.02 JRR10034 J10000R2 J10000P2

2-9/16 J10041L 3-5/8 2-3/8 1-3/8 3-5/16 5 6.33 JRR10040 - -

2-5/5 J10042L 3-3/4 2-3/8 1-1/2 3-7/16 5 6.75 JRR10040 - -

2-3/4 J10044L 3-7/8 2-3/8 1-3/4 3-1/2 5 7.10 JRR10040 - -

2-13/16 J10045L 4 2-3/4 1-3/4 3-9/16 5 8.15 - - -

2-7/8 J10046L 4 2-3/4 1-3/4 3-9/16 5 8.15 - - -

2-15/16 J10047L 4 2-3/4 1-3/4 3-9/16 5 10.00 - - -

3 J10048L 4-3/16 2-3/4 2 3-5/8 5 10.30 - - -

3-1/8 J10050L 4-3/16 2-3/4 1-15/16 3-5/8 5-1/2 11.84 - - -

3-1/4 J10052L 4-17/32 2-3/4 2 3-5/8 5-5/8 13.50 - - -

3-3/8 J10054L 4-17/32 2-3/4 2 3-3/4 5-3/4 14.05 - - -

3-1/2 J10056L 4-3/4 2-3/4 2-13/64 3-3/4 6 15.85 - - -

3-5/8 J10058L 4-55/64 3-1/4 2-1/2 3-7/8 6-1/8 16.95 - - -

3-3/4 J10060L 5 3-1/4 2-1/2 3-7/8 6-1/4 18.15 - - -

3-7/8 J10062L 5-7/64 3-1/4 2-1/2 3-7/8 6-3/8 18.65 - - -

4 J10064L 5-1/4 3-1/4 2-1/2 4 6-1/2 19.40 - - -

4-1/8 J10066L 5-3/8 3-1/4 2-19/32 4-1/8 6-3/4 21.30 - - -

4-1/4 J10068L 5-17/32 3-1/4 2-3/4 4-1/8 7 23.50 - - -

4-1/2 J10072L 5-13/16 3-1/4 2-27/32 4-3/16 7-1/4 26.00 - - -

7


Impact Sockets

MM 6

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Overall

Length (in) (L)

Weight (lbs)

24 J10024ML 1-9/16 2 35/64 4 1.76

27 J10027ML 1-3/4 2 5/8 4 1.82

28 J10028ML 1-13/16 2 41/64 4 1.84

30 J10030ML 1-31/32 2-1/16 21/32 4 2.10

32 J10032ML 2-1/16 2-1/16 3/4 4 2.24

33 J10033ML 2-1/16 2-1/16 49/64 4 2.30

35 J10035ML 2-1/4 2-7/64 51/64 4 2.34

36 J10036ML 2-1/4 2-7/64 27/32 4 2.50

38 J10038ML 2-1/4 2-7/64 7/8 4 2.78

41 J10041ML 2-1/2 2-15/64 63/64 4 3.10

46 J10046ML 2-3/4 2-27/64 1-1/8 4-1/8 3.84

50 J10050ML 2-63/64 2-27/64 1-3/16 4-1/4 4.04

55 J10055ML 3-1/4 2-27/64 1-21/64 4-1/2 4.94

60 J10060ML 3-1/2 2-27/64 1-25/64 4-3/4 6.04

65 J10065ML 3-45/64 2-47/64 1-33/64 4-7/8 7.05

70 J10070ML 3-53/64 2-47/64 1-5/8 5 7.62

75 J10075ML 4-1/64 2-47/64 1-47/64 5-1/4 10.70

80 J10080ML 4-11/64 2-47/64 1-55/64 5-1/2 11.85

7

1" Drive impact Sockets & Adapters

1" Drive Impact Adapters



>


large drive tools.

Product #

INCH

Overall


J15007 1-1/2" F x 1" M 4-3/16 5.03

J07655 3/4" F x 1"M 2-1/2 0.89

J07656 1" F x 3/4" M 2-7/8 1.42

J10004 1" F x 1-1/2" M 3-1/2 2.64

7 ASME B107.2

1" Drive Impact Adapter - Male Spline



> > Do not over torque small sockets when using them with adapters on

large drive tools.

Product # INCH x SPL Overall


J10005 1" SQ. F x #5 SPL. M 4-1/2 2.58

7


Torx ® hex HEX

BLACK OXIDE



1" Drive impact Universal Joint & extensions

1" Drive Impact Universal Joint


>

>


> Designed to withstand the high torque and force associated with impact








Overall

Product #

Length (in)

Weight (lbs)

J10670A 4-19/32 3.98

1" Drive Budd Wheel Deep Impact Socket - 6 Point

> > Double opening: 13/16" square threads studs onto wheel, 1-1/2" hex

tightens lug nuts.

7

Nut End

Drive End

Overall

INCH 6

Outside Diameter (in) Outside Diameter (in) Length (in)

Weight (lbs)

1-1/2 J10024LS 2-3/8 2-3/8 4 2.96

7

1" Drive Impact Extensions






with drive tools.





Product #

Overall

Length (in)

Weight (lbs)

J10607 7-3/8 3.54

J10608 10 4.49

J10609 13 5.81

7


Impact Sockets

1" Drive Retaining Rings

> > Large drive size crush gauge retaining ring.

>

> Part numbers are embossed on the rings near the point at which the pin

and ring meet.


JRR10028 Retaining Ring 1" DR 1-3/4" Groove 1-3/4 1-15/16 3/16 0.01

JRR10032 Retaining Ring 1" DR 2" Groove 2 2-3/16 3/16 0.01





1" Drive O-Rings

> > J10000R1 - “O” ring for impact sockets with a 1" drive.

> > Use with:

> > J10012 thru J10023

> > J10019M thru J10036M

> > J10012SS thru J10018SS

>

> J100185, J10017-LT, J10020-LT, J10607, J10608, J10609

> > J10000R2 - “O” ring for impact sockets with a 1" drive.

> > Use with:

> > J10024 thru J10072

> > J10041M thru J10065M

> > J10024L thru J10044L

> > J10024LS, J10670, J10004, J10005

7

1" Drive impact Retaining Rings & Pins

Product #

Weight (lbs)

J10000R1 0.01

J10000R2 0.01

7

1" Drive Retaining Pins

>

> > Use with:

> > J10012 thru J10023

> > J10019M thru J10036M

> > J10012SS thru J10018SS

>

> J10000P1 - Use for a variety of impact sockets and attachments.

> J100185, J10017-LT, J10020-LT, J10607, J10608, J10609

> > J10000P2 - Use for a variety of impact sockets and attachments.

> > Use with:

> > J10024 thru J10072

> > J10041M thru J10065M

> > J10024L thru J10044L

> > J10024LS, J10670, J10004, J10005

Product #

Weight (lbs)

J10000P1 0.02

J10000P2 0.02

7


Torx ® hex HEX

BLACK OXIDE



1-1/2" Drive impact Sockets

1 - 1/2" Drive Impact Sockets - 6 POINT






L

B

A

C

D

E






Crush Retaining

INCH 6 Diameter (in) (B) Diameter (in) (C) (in) (D) Depth (in) (E) Length (in) (L) Weight (lbs) Ring

1-5/16 J15021 2-3/4 3-1/4 3/4 1-3/8 3-1/8 4.78 JRR15046

1-3/8 J15022 2-19/32 3-1/4 7/8 1-1/2 3-1/8 4.69 JRR15046

1-7/16 J15023 2-19/32 3-1/4 7/8 1-1/2 3-1/8 4.76 JRR15046

1-1/2 J15024 2-19/32 3-1/4 15/16 1-1/2 3-1/8 4.67 JRR15046

1-9/16 J15025 2-3/4 3-1/4 31/32 1-1/2 3-1/8 4.78 JRR15046

1-5/8 J15026 2-7/8 3-1/4 31/32 1-1/2 3-1/8 4.91 JRR15046

1-11/16 J15027 2-7/8 3-1/4 1-1/16 1-19/32 3-15/64 5.01 JRR15046

1-3/4 J15028 2-15/16 3-1/4 1-3/32 1-21/32 3-11/32 5.22 JRR15046

1-13/16 J15029 3 3-1/4 1-1/8 1-21/32 3-11/32 5.00 JRR15046

1-7/8 J15030 3 3-1/4 1-3/16 1-45/64 3-11/32 5.33 JRR15046

1-15/16 J15031 3 3-1/4 1-1/8 2 3-5/8 5.33 JRR15046

2 J15032 3-1/4 3-1/4 1-1/4 1-13/32 3-5/8 5.65 JRR15046

2-1/16 J15033 3-1/4 3-1/4 1-9/32 1-11/16 3-5/8 5.50 JRR15046

2-1/8 J15034 3-1/2 3-1/4 1-11/32 1-43/64 3-5/8 6.68 JRR15054

2-3/16 J15035 3-1/2 3-1/4 1-3/8 1-21/32 3-5/8 6.47 JRR15054

2-1/4 J15036 3-1/2 3-1/4 1-1/2 1-3/4 3-3/4 7.98 JRR15054

2-5/16 J15037 3-1/2 3-1/4 1-1/2 1-53/64 3-7/8 7.93 JRR15054

2-3/8 J15038 3-1/4 3-1/4 1-9/16 1-55/64 3-7/8 7.90 JRR15054

2-7/16 J15039 3-3/4 3-1/4 1-9/16 1-15/16 3-7/8 8.52 JRR15054

2-1/2 J15040 3-3/4 3-1/4 1-5/8 1-59/64 4 8.40 JRR15054

2-9/16 J15041 3-3/4 3-1/4 1-5/8 1-29/32 4 8.92 JRR15054

2-5/8 J15042 4-1/8 3-1/4 1-5/8 2 4-1/8 8.84 JRR15054

2-11/16 J15043 4-1/8 3-1/4 1-3/4 2-7/64 4-1/4 9.25 JRR15054

2-3/4 J15044 4-1/4 3-1/4 1-3/4 2-5/64 4-1/4 10.03 JRR15054

2-13/16 J15045 4-1/4 3-1/4 1-7/8 2-3/16 4-3/8 9.83 JRR15054

2-7/8 J15046 4-1/2 3-1/4 1-7/8 2-11/64 4-3/8 11.36 JRR15054

2-15/16 J15047 4-1/2 3-1/4 2 2-17/16 4-1/2 11.24 JRR15054

3 J15048 4-1/2 3-1/4 2 2-1/4 4-1/2 12.59 JRR15054

3-1/16 J15049 4-3/4 3-1/4 2 2-23/64 4-5/8 12.53 JRR15054

3-1/8 J15050 4-3/4 3-1/4 2 2-23/64 4-5/8 12.42 JRR15054

3-3/16 J15051 4-3/4 3-1/4 2 2-9/16 4-23/32 12.15 JRR15054

3-1/4 J15052 5 3-1/4 2 2-35/64 4-23/32 14.08 JRR15054

3-5/16 J15053 5 3-1/4 2 2-31/64 4-23/32 13.79 JRR15054

3-3/8 J15054 5 3-1/4 2 2-33/64 4-23/32 13.67 JRR15054

3-7/16 J15055 5 3-1/4 2 2-39/64 4-31/32 13.44 -

3-1/2 J15056 5-1/8 3-1/4 2-1/4 2-37/64 4-31/32 14.46 -

3-9/16 J15057 5-1/8 3-1/4 2-1/4 2-9/16 5 12.54 -

3-5/8 J15058 5-1/8 3-1/4 2-1/4 2-35/64 5 14.73 -

3-11/16 J15059 5-1/8 3-1/4 2-1/4 2-33/64 5 14.67 -

7 ASME B107.2


Impact Sockets

INCH 6

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Bolt Clearance

Depth (in) (E)

Overall

Length (in) (L)

Weight (lbs)

Crush Retaining

Ring

3-3/4 J15060 5-1/2 3-1/4 2-1/4 2-1/2 5 16.75 -

3-13/16 J15061 5-1/2 3-1/4 2-1/4 2-31/64 5 19.49 -

3-7/8 J15062 5-1/2 3-1/4 2-1/4 2-31/32 5-1/2 18.70 -

3-15/16 J15063 5-3/4 3-1/4 2-1/2 2-15/16 5-1/2 21.33 -

4 J15064 5-3/4 3-1/4 2-1/2 2-59/64 5-1/2 20.66 -

4-1/16 J15065 5-3/4 3-1/4 2-3/4 2-29/32 5-1/2 20.25 -

4-1/8 J15066 6 3-1/4 2-3/4 3-1/8 5-3/4 26.72 -

5 J15067 6-11/16 3-3/4 3-1/8 4-5/8 6-1/4 26.17 -

4-1/4 J15068 6 3-1/4 2-3/4 3-5/64 5-3/4 27.05 -

4-5/16 J15069 6 3-1/4 2-3/4 3-1/16 5-3/4 27.66 -

4-3/8 J15070 6-1/4 3-1/4 2-3/4 3-3/64 5-3/4 28.23 -

4-7/16 J15071 6-1/4 3-1/4 3 3-17/64 6 18.63 -

4-1/2 J15072 6-1/4 3-1/4 3 3-1/4 6 28.40 -

4-5/8 J15074 6-1/2 3-1/4 3 3-15/32 6-1/4 29.98 -

4-3/4 J15076 6-1/2 3-1/4 3 3-27/64 6-1/4 30.15 -

5 J15080 6-3/4 3-1/2 3 3-1/2 6-3/4 25.16 -

7 ASME B107.2


MM 6

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Bolt Clearance

Depth (in) (E)

Overall

Length (in)

(L)

Weight

(lbs)

Crush

Retaining Ring

O-Ring

Retaining

Pin

36 J15036M 2-3/4 3-1/4 7/8 1-3/8 3-3/16 4.73 JRR10034 J10000R2 J10000P2

38 J15038M 2-7/8 3-1/4 7/8 1-7/16 3-1/4 4.85 JRR10034 J10000R2 J10000P2

60 J15060M 3-5/8 3-5/8 1-3/8 2-3/8 4 8.71 - - -

65 J15065M 3-7/8 3-7/8 1-1/2 2-1/2 4-3/16 8.75 - - -

70 J15070M 4-1/16 3-3/4 1-5/8 2-3/4 4-3/8 9.72 - - -

75 J15075M 4-5/16 3-3/4 1-3/4 2-7/8 4-1/2 11.04 - - -

7


Torx ® hex HEX

BLACK OXIDE




1 - 1/2" Drive Deep Impact Sockets - 6 POINT






L

B

A

C

D


Retaining


1-5/16 J15021L 2-3/4 3-1/4 13/16 4 5-11/16 10.23 JRR15046 J10000R2 J10000P2

1-3/8 J15022L 2-19/32 3-1/4 7/8 4-1/8 5-3/4 9.18 JRR15046 J10000R2 J10000P2

1-7/16 J15023L 2-19/32 3-1/4 7/8 4-1/8 5-3/4 9.09 JRR15046 - -

1-1/2 J15024L 2-19/32 3-1/4 15/16 4-1/8 5-3/4 9.13 JRR15046 - -

1-9/16 J15025L 2-7/8 3-1/4 31/32 4-1/8 5-3/4 8.86 JRR15046 - -

1-5/8 J15026L 2-7/8 3-1/4 31/32 4-1/8 5-3/4 9.37 JRR15046 - -

1-11/16 J15027L 2-7/8 3-1/4 1-1/16 4-1/8 5-3/4 9.19 JRR15046 - -

1-3/4 J15028L 2-15/16 3-1/4 1-3/32 4-1/8 5-3/4 8.80 JRR15046 - -

1-13/16 J15029L 3-1/8 3-1/4 1-1/8 4-1/8 5-3/4 9.52 JRR15046 - -

1-7/8 J15030L 3-1/8 3-1/4 1-3/16 4-1/8 5-3/4 9.30 JRR15046 - -

1-15/16 J15031L 3-1/8 3-1/4 1-1/8 4-1/8 5-3/4 8.78 JRR15046 - -

2 J15032L 3-1/4 3-1/4 1-21/32 3-53/64 5-3/4 9.40 JRR15046 - -

2-1/16 J15033L 3-1/4 3-1/4 1-45/64 3-13/16 5-3/4 8.27 JRR15046 - -

2-1/8 J15034L 3-1/2 3-1/4 1-3/4 3-57/64 5-3/4 9.35 JRR15054 J10000R2 J10000P2

2-3/16 J15035L 3-1/2 3-1/4 1-51/64 3-57/64 5-3/4 8.83 JRR15054 J10000R2 J10000P2

2-1/4 J15036L 3-1/2 3-1/4 1-27/32 3-57/64 5-7/8 8.78 JRR15054 - -

2-5/16 J15037L 3-1/2 3-1/4 1-29/32 3-57/64 5-7/8 8.47 JRR15054 - -

2-3/8 J15038L 3-3/4 3-1/4 1-61/64 3-57/64 5-7/8 12.21 JRR15054 - -

2-7/16 J15039L 3-3/4 3-1/4 2-1/64 3-15/16 6 13.56 JRR15054 - -

2-1/2 J15040L 3-3/4 3-1/4 2-1/16 3-59/64 6 13.41 JRR15054 - -

2-9/16 J15041L 3-3/4 3-1/4 2-7/64 3-57/64 6 14.28 JRR15054 - -

2-5/8 J15042L 4-1/8 3-1/4 2-5/32 3-57/64 6 11.59 JRR15054 - -

2-11/16 J15043L 4-1/8 3-1/4 2-7/32 3-63/64 6-1/8 14.50 JRR15054 - -

2-3/4 J15044L 4-1/4 3-1/4 2-17/64 3-31/32 6-1/8 15.25 JRR15054 - -

2-13/16 J15045L 4-1/4 3-1/4 2-5/16 4-1/16 6-1/4 15.53 JRR15054 - -

2-7/8 J15046L 4-1/2 3-1/4 2-3/8 4-3/64 6-1/4 17.74 JRR15054 - -

2-15/16 J15047L 4-1/2 3-1/4 2-27/64 4-1/64 6-1/4 17.25 JRR15054 - -

7 ASME B107.2

E






Impact Sockets

INCH 6



Nut Depth

(in) (D)

Bolt Clearance

Depth (in) (E)

Overall

Length (in) (L)

Weight

(lbs)

Crush Retaining

Ring

3 J15048L 4-1/2 3-1/4 2-15/32 4-1/8 6-3/8 19.17 JRR15054 - -

3-1/16 J15049L 4-3/4 3-1/4 2-33/64 4-1/8 6-3/8 15.76 JRR15054 - -

3-1/8 J15050L 4-3/4 3-1/4 2-37/64 4-5/64 6-3/8 18.89 JRR15054 - -

3-3/16 J15051L 4-3/4 3-1/4 2-5/8 4-3/16 6-1/2 19.16 JRR15054 - -

3-1/4 J15052L 5 3-1/4 2-43/64 4-5/32 6-1/2 21.66 JRR15054 - -

3-5/16 J15053L 5 3-1/4 2-47/64 4-1/8 6-1/2 21.33 JRR15054 - -

3-3/8 J15054L 5 3-1/4 2-25/32 4-1/8 6-1/2 21.10 JRR15054 - -

3-7/16 J15055L 5 3-1/4 2-27/32 4-7/64 6-1/2 20.78 - - -

3-1/2 J15056L 5-1/8 3-1/4 2-7/8 4-5/64 6-1/2 21.68 - - -

3-9/16 J15057L 5-1/8 3-1/4 2-15/16 4-5/16 6-3/4 17.24 - - -

3-5/8 J15058L 5-1/8 3-1/4 2-63/64 4-19/64 6-3/4 17.48 - - -

3-11/16 J15059L 5-1/8 3-1/4 3-1/32 4-17/64 6-3/4 16.2 - - -

3-3/4 J15060L 5-1/2 3-1/4 3-3/32 4-15/64 6-3/4 26.63 - - -

3-13/16 J15061L 5-1/2 3-1/4 3-9/64 4-15/64 6-3/4 18.52 - - -

3-7/8 J15062L 5-1/2 3-1/4 3-3/16 4-7/32 6-3/4 27.36 - - -

3-15/16 J15063L 5-3/4 3-1/4 3-1/4 4-7/16 7 21.16 - - -

4 J15064L 5-3/4 3-1/4 3-19/64 4-7/16 7 30.47 - - -

4-1/16 J15065L 5-3/4 3-1/4 3-11/32 4-25/64 7 19.43 - - -

4-1/8 J15066L 6 3-1/4 3-25/64 4-25/64 7 36.26 - - -

4-3/16 J15067L 6 3-1/4 3-7/16 5-1/32 7-1/4 21.71 - - -

4-1/4 J15068L 6 3-1/4 3-1/2 4-37/64 7-1/4 22.36 - - -

4-5/16 J15069L 6 3-1/4 3-9/16 4-9/16 7-1/4 28.73 - - -

4-3/8 J15070L 6-1/4 3-1/4 3-39/64 4-35/64 7-1/4 24.04 - - -

4-1/2 J15072L 6-1/4 3-1/4 3-45/64 4-1/2 7-1/4 35.85 - - -

4-5/8 J15074L 6-1/2 3-1/4 3-13/16 4-23/32 7-1/2 41.32 - - -

O-Ring

Retaining

Pin

4-3/4 J15076L 6-1/2 3-1/4 3-29/32 4-43/64 7-1/2 24.23 - - -

7 ASME B107.2



Torx ® hex HEX

BLACK OXIDE



1-1/2" Drive impact Extensions & Adapters

1 - 1/2" Drive Impact Extensions














> > Male square is oriented in line with female squares for use with fixed head

torque wrenches.

> > Full chamfer at drive opening (when applicable) for easy engagement with

drive tools.

Product #

Overall

Length (in)

Weight (lbs)

J15097P 8 9.17

J15098P 12 12.66

J15099P 15 15.58

7

1 - 1/2" Drive Impact Adapters



>


large drive tools.

Product #

INCH

Overall


J15007 1-1/2" F x 1" M 4-3/16 5.03

J10004 1" F x 1-1/2" M 3-1/2 2.64

7 ASME B107.2

1 - 1/2" Drive Impact Adapter - Male Spline




large drive tools.

Product # INCH SPL Overall


J15005 1-1/2" F x #5 SPL. M 5-3/8 5.94

7 ASME B107.2


Impact Sockets

1 - 1/2" Drive Retaining Rings


>


and ring meet.


JRR15046 Retaining RIng, CG 1-1/2" DR 2-7/8 Groove 2-7/8 3-3/8 1/4 0.03




7

1-1/2" Drive Retaining Rings & Universal Joint

1 - 1/2" Drive Impact Universal Joint


> > Used wherever powered drive tools are used to install or remove fasteners.

>

>

> Designed to withstand the high torque and force associated with impact tools in repetitive application.

> Features two through holes and a groove to accept a Proto ® Retaining Ring or pin and O-ring to help

secure the socket to the drive tool anvil.

> > Position at appropriate angle to turn fasteners where obstructions prevent a straight application.



Overall

Product #

Length (in)

Weight (lbs)

J15670A 6-19/64 9.35

7


Torx ® hex HEX

BLACK OXIDE




2 - 1/2" Drive Impact Sockets - 6 pOINT

> > Proto ® 6 Point Impact Sockets are ideal for

use on stubborn or damaged

fasteners, and also on fasteners made from

soft materials.

L

B

A

>

C

D

E







1-3/4 J25028 4-3/16 5 1-1/8 2-7/8 5-3/8 21.08

1-7/8 J25030 4-5/16 5 1-3/16 2-7/8 5-3/8 20.97

2 J25032 4-3/8 5 1-1/4 2-7/8 5-3/8 20.80

2-1/8 J25034 4-1/2 5 1-3/8 2-7/8 5-3/8 20.59

2-1/4 J25036 4-9/16 5 1-7/16 3 5-1/2 21.06

2-3/8 J25038 4-5/8 5 1-1/2 3 5-1/2 20.85

2-1/2 J25040 4-3/4 5 1-9/16 3 5-1/2 20.65

2-9/16 J25041 4-3/4 5 1-5/8 3 5-1/2 20.61

2-5/8 J25042 4-13/16 5 1-11/16 3 5-1/2 20.53

2-3/4 J25044 4-15/16 5 1-3/4 3-1/8 5-5/8 20.89

2-7/8 J25046 5 5 1-13/16 3-1/8 5-5/8 20.87

2-15/16 J25047 5-1/16 5-1/16 1-7/8 3-1/8 5-5/8 21.16

3 J25048 5-1/8 5-1/8 2 3-1/8 5-5/8 21.30

3-1/8 J25050 5-3/16 5-3/16 2 3-1/4 5-3/4 22.63

3-1/4 J25052 5-5/16 5-5/16 2-1/16 3-1/4 5-3/4 23.79

3-3/8 J25054 5-7/16 5-7/16 2-1/8 3-1/4 5-3/4 24.84

3-7/16 J25055 5-1/2 5-1/2 2-3/16 3-1/4 5-3/4 25.29

3-1/2 J25056 5-9/16 5-9/16 2-1/4 3-1/4 5-3/4 25.77

3-5/8 J25058 5-11/16 5-11/16 2-5/16 3-1/4 5-3/4 26.99

3-3/4 J25060 5-13/16 5-13/16 2-3/8 3-3/4 6-1/4 31.04

3-7/8 J25062 5-15/16 5-15/16 2-1/2 3-3/4 6-1/4 32.27

4 J25064 6-1/16 6-1/16 2-1/2 3-3/4 6-1/4 33.70

4-1/8 J25066 6-3/16 6 2-5/8 3-3/4 6-1/4 34.69

4-1/4 J25068 6-5/16 6 2-3/4 4-1/4 6-3/4 37.32

4-3/8 J25070 6-7/16 6 2-3/4 4-1/4 6-3/4 38.04

4-1/2 J25072 6-9/16 6 2-7/8 4-1/2 7 40.41

4-5/8 J25074 6-11/16 6 3 4-1/2 7 40.54

4-3/4 J25076 6-13/16 6 3 4-1/2 7 41.29

4-7/8 J25078 6-15/16 6 3 4-3/4 7-1/4 42.94

5 J25080 7-1/16 6 3-3/16 5 7-1/2 45.46

5-1/8 J25082 7-1/4 6 3-5/16 5 7-1/2 46.12

5-1/4 J25084 7-3/8 6 3-5/16 5 7-1/2 47.47

5-3/8 J25086 7-1/2 6 3-3/8 5-1/4 7-3/4 50.48

5-7/16 J25087 7-9/16 6 3-7/16 5-1/4 7-3/4 50.92

5-1/2 J25088 7-5/8 6 3-1/2 5-1/4 7-3/4 51.41

5-5/8 J25090 7-13/16 6 3-9/16 5-1/4 7-3/4 52.50

5-3/4 J25092 7-15/16 6 3-5/8 5-1/4 7-3/4 53.43

5-7/8 J25094 8-1/16 6 3-3/4 5-1/4 7-3/4 53.75

6 J25096 8-1/4 6 3-13/16 5-3/8 7-7/8 56.13

6-1/8 J25098 8-3/8 6 3-7/8 5-3/8 7-7/8 56.72

6-1/4 J25100 8-1/2 6 3-7/8 5-3/8 7-7/8 57.61

6-3/8 J25102 8-11/16 6 4 5-1/2 8 59.32

6-1/2 J25104 8-13/16 6 4 5-1/2 8 60.35

6-5/8 J25106 8-15/16 6-1/2 4-1/4 5-1/2 8 63.91

6-3/4 J25108 9-1/8 6-1/2 4-1/4 5-1/2 8 64.60

6-7/8 J25110 9-1/4 6-1/2 4-5/16 5-1/2 8 65.05

7 J25112 9-3/8 6-1/2 4-5/16 5-1/2 8 66.10

7-1/8 J25114 9-9/16 6-1/2 4-5/16 5-1/2 8 67.21

7-1/4 J25116 9-11/16 6-1/2 4-5/16 6 8-1/2 75.16

7-3/8 J25118 9-13/16 6-1/2 4-5/16 6 8-1/2 76.28

7-1/2 J25120 10 6-1/2 4-5/16 6 8-1/2 77.24

7-5/8 J25122 10-1/8 6-1/2 4-5/16 6 8-1/2 77.98

7-3/4 J25124 10-1/4 6-1/2 4-5/16 6 8-1/2 78.65

7-7/8 J25126 10-3/8 6-1/2 4-5/16 6-1/4 8-3/4 84.00

8 J25128 10-9/16 6-1/2 4-5/16 6-1/4 8-3/4 86.44

7


Impact Sockets

2 - 1/2" Drive Retaining Pin


>


and ring meet.


JRP25000 Retaining Pin, 2-1/2" DR 2 4-1/2 1/2 0.21

#5 Spline Drive Impact Adapters - Male Square




large drive tools.

7

#5 Spline Drive impact Sockets & Adapters

Overall

SPL

Product #

x INCH Length (in) Weight (lbs)

J09902 #5 SPL. F x 1" SQ. M 4-3/8 2.16

J09904 #5 SPL. F x 1-1/2" SQ. M 5 2.74

7

#5 Spline Drive Budd Wheel Deep Impact Socket



L

>

>

B

A

>

D

E

C


Overall

INCH 6

Diameter (in) (B) Diameter (in) (C) Length (in) (L)

Weight (lbs)

1-1/2 J09924-LS 2-3/8 2-3/8 4-3/16 3.10








7

#5 Spline Drive impact Sockets

#5 Spline Drive Impact Sockets








INCH

SPL


Diameter (in) (B) Diameter (in) (C) (in) (D) Depth (in) (E) Length (in) (L) Weight (lbs)

15/16 J09915 1-5/8 2-3/8 19/32 1-1/2 3 1.94

1 J09916 1-11/16 2-3/8 5/8 1-1/2 3-1/8 1.91

1-1/16 J09917 1-11/16 2-3/8 43/64 1-1/2 3-1/8 1.92

1-1/8 J09918 1-7/8 2-3/8 23/32 1-1/2 3-1/4 2.09

1-3/16 J09919 1-7/8 2-3/8 3/4 1-1/2 3-1/4 2.10

1-1/4 J09920 2-3/8 2-3/8 25/32 1-1/2 3-1/4 2.21

1-5/16 J09921 2-3/8 2-3/8 53/64 1-5/8 3-1/4 2.23

1-3/8 J09922 2-3/8 2-3/8 55/64 1-5/8 3-3/8 2.23

1-7/16 J09923 2-1/2 2-3/8 29/32 29/32 3-3/8 2.43

1-1/2 J09924 2-1/2 2-3/8 15/16 15/16 3-3/8 2.46

1-9/16 J09925 2-3/4 2-3/8 63/64 63/64 3-1/2 2.69

1-5/8 J09926 2-3/4 2-3/8 1-1/64 1-1/64 3-5/8 2.94

1-11/16 J09927 2-15/16 2-3/8 1-27/64 2-1/8 3-5/8 2.95

1-3/4 J09928 2-15/16 2-3/8 1-7/64 1-27/64 3-47/64 3.11

1-13/16 J09929 3-1/8 2-3/8 1-1/8 1-27/64 3-7/16 3.27

1-7/8 J09930 3-1/8 2-3/8 1-3/16 1-1/2 3-17/32 3.25

1-15/16 J09931 3-1/8 2-3/8 1-1/4 1-1/2 3-17/32 3.43

2 J09932 3-1/4 2-3/8 1-1/4 1-15/32 3-17/32 3.66

2-1/16 J09933 3-1/4 2-3/8 1-19/32 2-1/8 4 3.89

2-1/8 J09934 3-1/2 2-3/8 1-37/64 2-1/8 3-11/16 4.63

2-3/16 J09935 3-1/2 2-3/8 1-3/8 1-39/64 3-3/4 4.28

2-1/4 J09936 3-1/2 2-3/8 1-1/2 1-23/32 4-3/16 4.52

2-5/16 J09937 3-1/2 2-3/8 1-23/32 2-7/16 3-57/64 4.44

2-3/8 J09938 3-3/4 2-3/8 1-11/16 2-7/16 3-57/64 4.80

2-7/16 J09939 3-3/4 2-3/8 1-25/32 2-13/16 4 5.29

2-1/2 J09940 3-3/4 2-3/8 1-53/64 2-13/16 4-3/8 5.11

2-9/16 J09941 3-3/4 2-3/8 1-5/8 1-55/64 4-3/8 6.45

2-5/8 J09942 4-1/8 2-3/8 1-59/64 2-13/16 4-1/2 6.68

2-3/4 J09944 4-1/4 2-3/8 1-3/4 1-59/64 4-1/4 6.89

2-15/16 J09947 4-1/2 2-3/8 2-5/32 3 4-13/16 8.22

3 J09948 4-1/2 2-3/8 2 2-13/64 4-39/64 7.93

3-1/8 J09950 4-3/4 2-3/8 2 2-13/64 4-39/64 7.95

7


Impact Sockets

1/4" Drive High Strength Magnetic Impact Sockets - 6 Point

> > ProtoGrip Magnetic Sockets use high strength magnets made from a rare

earth magnet alloy/nylon blend.

> > ProtoGrip Magnetic Sockets require no bushings to hold the magnet

in place. Allows room for more magnet material, helping increase total

magnetic strength.

> > Designed to easily pick up heavy fasteners and hold them tightly during use.

> > Strong magnetic hold helps increase efficiency when installing fasteners in

awkward or hard-to-reach locations.

> > Impact sockets with high impact strength are used in automated and hand

impact socket applications.



Overall

INCH 6

Diameter (in) (B) Diameter (in) (C) (in) (D) Length (in) (L) Weight (lbs)

3/16 J6906HF 5/16 1/2 5/32 7/8 0.03

1/4 J6908HF 25/64 1/2 11/64 7/8 0.04

5/16 J6910HF 1/2 1/2 13/64 59/64 0.04

3/8 J6912HF 9/16 9/16 15/64 15/16 0.05

7/16 J6914HF 21/32 21/32 1/4 1 0.07

1/2 J6916HF 11/16 11/16 1/4 1 0.07

7 ASME B107.2

L

B

A

C

D

E

1/4" Drive Magnetic Impact Sockets


Overall

MM 6


5 J6905MHF 5/16 1/2 1/16 7/8 0.03

5.5 J69055MHF 23/64 1/2 3/32 7/8 0.03

6 J6906MHF 25/64 1/2 7/64 7/8 0.06

7 J6907MHF 25/64 1/2 7/64 15/16 0.04

8 J6908MHF 1/2 1/2 1/8 15/16 0.04

10 J6910MHF 9/16 9/16 5/32 15/16 0.05

7 ASME B107.33M


Torx ® hex HEX

BLACK OXIDE




B

A

3/8" & 1/2" Drive Magnetic Sockets

INCH 6

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Overall

Length (in) (L)

Weight (lbs)

1/4 J7208HF 7/16 11/16 11/64 1-3/32 0.07

5/16 J7210HF 1/2 11/16 3/16 1-3/32 0.08

3/8 J7212HF 39/64 11/16 15/64 1-3/32 0.08

7/16 J7214HF 11/16 11/16 1/4 1-3/32 0.08

1/2 J7216HF 3/4 3/4 9/32 1-3/32 0.08

9/16 J7218HF 13/16 13/16 21/64 1-3/32 0.12

5/8 J7220HF 29/32 29/32 23/64 1-7/32 0.16

7 ASME B107.33M

MM 6

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Overall

Length (in) (L)

Weight (lbs)

7 J7207MHF 31/64 11/16 11/64 1-3/32 0.08

8 J7208MHF 1/2 11/16 11/64 1-3/32 0.07

10 J7210MHF 5/8 11/16 7/32 1-9/64 0.08

11 J7211MHF 11/16 11/16 17/64 1-9/64 0.08

12 J7212MHF 47/64 47/64 9/32 1-9/64 0.09

13 J7213MHF 3/4 3/4 19/64 1-13/64 0.10

14 J7214MHF 13/16 13/16 21/64 1-13/64 0.12

15 J7215MHF 55/64 55/64 21/64 1-13/64 0.14

17 J7217MHF 1 1 25/64 1-1/4 0.20

18 J7218MHF 1-1/32 1-1/32 25/64 1-1/4 0.21

7 ASME B107.33

L

C

D

E


B

A

D

L

E

INCH 6

MM 6

Nut End Outside

Diameter (in) (B)

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Nut Depth

(in) (D)

Overall

Length (in) (L)

Overall

Length (in) (L)

Weight (lbs)

3/8 J7412HF 47/64 15/16 15/64 1-1/2 0.18

7/16 J7414HF 45/64 15/16 1/4 1-1/2 0.19

1/2 J7416HF 25/32 15/16 17/64 1-1/2 0.19

9/16 J7418HF 7/8 15/16 21/64 1-1/2 0.20

5/8 J7420HF 1 1 25/64 1-1/2 0.23

7 ASME B107.2

Weight (lbs)

10 J7410MHF 41/64 15/16 7/32 1-1/2 0.19

13 J7413MHF 51/64 15/16 17/64 1-1/2 0.19

14 J7414MHF 15/16 15/16 9/32 1-1/2 0.20

15 J7415MHF 15/16 15/16 9/32 1-1/2 0.21

18 J7418MHF 1-1/16 1-1/16 13/32 1-1/2 0.27

7 ASME B107.2

C


Impact Sockets

About Power SOckets

VERY DIFFERENT SOCKETS FOR VERY DIFFERENT PURPOSES

Power sockets are designed for power nut runners,

multi-spindle machines and angle head nut drivers,

which are low impact power tools. Even though

the power sockets are offered in a black finish,

they are not compatible with impact tools.

1/4" Drive High Strength Magnetic Power Sockets - 6 Point

> > ProtoGrip Magnetic Sockets use high strength magnets made from a rare

earth magnet alloy/nylon blend.

> > ProtoGrip Magnetic Sockets require no bushings to hold the magnet

in place. Allows room for more magnet material, helping increase total

magnetic strength.


> > Strong magnetic hold helps increase efficiency when installing fasteners in

awkward or hard-to-reach locations.


Power sockets are heat-treated to a higher

hardness than either impact or hand sockets. This

high hardness is ideal for long wear on assembly

lines, but their brittleness makes them vulnerable

to shattering when fitted to an impact wrench.

L

B

A

D

E

1/4" Drive Power Sockets

C


Overall

INCH 6


3/16 J6906PF 5/16 1/2 5/32 7/8 0.03

1/4 J6908PF 25/64 1/2 11/64 7/8 0.03

5/16 J6910PF 1/2 1/2 13/64 15/16 0.04

11/32 J6911PF 33/64 33/64 7/32 15/16 0.04

3/8 J6912PF 9/16 9/16 15/64 15/16 0.05

7/16 J6914PF 21/32 21/32 1/4 1 0.07

1/2 J6916PF 11/16 11/16 1/4 1 0.08

7 ASME B107.2


Overall

MM 6


5 J6905MPF 5/16 1/2 5/32 7/8 0.03

5.5 J69055MPF 23/64 1/2 5/32 7/8 0.03

6 J6906MPF 25/64 1/2 11/64 7/8 0.03

7 J6907MPF 7/16 1/2 11/64 15/16 0.04

8 J6908MPF 1/2 1/2 11/64 15/16 0.04

9 J6909MPF 33/64 33/64 13/64 15/16 0.04

10 J6910MPF 9/16 9/16 7/32 15/16 0.05

11 J6911MPF 5/8 5/8 17/64 1 0.06

12 J6912MPF 11/16 11/16 9/32 1 0.08

13 J6913MPF 47/64 47/64 19/64 1 0.09

7 ASME B107.33M

Locking Adapter (Male to Male)

Product #: J4759BL

Overall

Product # Drive Size (in) Finish Length (in) Weight (lbs)

J4759BL 1/4 Black Oxide 2-1/2 0.07

7


Torx ® hex HEX

BLACK OXIDE



3/8" & 1/2" Drive Power Sockets


> > ProtoGrip Magnetic Sockets use high strength magnets made from a rare earth magnet alloy/nylon blend.

> > ProtoGrip B

Magnetic Sockets require no bushings to hold the magnet in place. This allows room for more

magnet material, helping increase total magnetic strength.


> > Strong magnetic hold helps increase efficiency when installing fasteners in awkward or hard-to-reach locations.

> > Impact sockets with high impact strength are used in automated and hand impact socket applications.



INCH 6

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Overall

Length (in) (L)

Weight (lbs)

5/16 J7210PF 1/2 11/16 3/16 1-3/32 0.08

3/8 J7212PF 39/64 11/16 15/64 1-3/32 0.09

7/16 J7214PF 11/16 11/16 1/4 1-3/16 0.08

1/2 J7216PF 3/4 3/4 9/32 1-3/16 0.10

9/16 J7218PF 13/16 13/16 21/64 1-3/16 0.11

7 ASME B107.2

MM 6

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Overall

Length (in) (L)

Weight (lbs)

7 J7207MPF 31/64 11/16 11/64 1-3/32 0.08

8 J7208MPF 1/2 11/16 7/32 1-3/32 0.07

10 J7210MPF 5/8 11/16 7/32 1-9/64 0.08

11 J7211MPF 11/16 11/16 17/64 1-9/64 0.08

12 J7212MPF 47/64 47/64 9/32 1-9/64 0.10

13 J7213MPF 3/4 3/4 19/64 1-13/64 0.10

15 J7215MPF 55/64 55/64 21/64 1-13/64 0.14

7 ASME B107.33M

L

A

C

D

E


B

A

D

L

E

INCH 6

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Overall

Length (in) (L)

Weight (lbs)

3/8 J7412PF 47/64 15/16 15/16 1-1/2 0.18

7/16 J7414PF 47/64 15/16 1/4 1-1/2 0.18

1/2 J7416PF 51/64 15/16 17/64 1-1/2 0.20

9/16 J7418PF 15/16 15/16 21/64 1-1/2 0.20

7 ASME B107.2

C

1/2" Drive Power Socket - 6 Point

Cotton Picker Socket

> > Removes and replaces spindles on cotton pickers.

INCH 6

Nut End Outside

Diameter (in) (B)

Drive End Outside

Diameter (in) (C)

Nut Depth

(in) (D)

Bolt Clearance

Depth (in) (E)

Overall

Length (in) (L)

Weight (lbs)

1-1/8 J7336CPB 1-9/16 1-9/16 5/8 5-7/64 5-49/64 1.67

7 ASME B107.2


Proto - Douilles à choc

Create successful ePaper yourself

Delete template?

Save as template?