reece 101 service

More documents

Recommendations

Info

S-101 CORD TRIM THREADING DIAGRAMS For tension threading details - see sheet 2 DETAIL CORD THREADING DIAGRAM See detail at right From cord supply Guide 1-24 Revised 09/2004 e-mail: service@amfreece.cz; parts@amfreece.cz; website: www.amfreece.com Phones: +420 582 309 146+ (Service), +420 582 309 286 (Spare Parts); Fax: +420 582 360 606
S-101 CORD TRIM - MACHINE ADJUSTMENT UPPER THREAD DRAW OFF AND TENSION ADJUSTMENTS Keep tension tight enough to bread the upper thread at the last stitch. Make sure that lever releases tension when the machine starts sewing, so that only tension will be effective during the sewing cycle. This tension should swing in the direction of arrow (Y) when the machine reaches the far end of its travel and in the direction of arrow (X) just before the machine stops. To obtain maximum length of starting thread at proceed as follows: Make sure machine is in its normal stopping position. Loosen screws and and rotate cam to the point where pin is at the bottom of the cam drop at as shown Figure 1. Then tighten screws and securely. To decrease the length of starting thread at , adjust the position of cam as required in the direction of arrow marked less, Figure 1. Note: For machines equipped with needle bar type upper thread draw off, see sheet 22. THREAD PICK-UP ADJUSTMENT The pick-up hook Figure 2 dips with the cutting lever and grasps the upper thread and holds it out of the way for the next buttonhole. - The extent of the dip downward so that it will not miss the thread is adjusted by loosening the screw and swinging the plate upon its fulcrum pin as desired. UNDER THREAD DRAW-OFF AND TENSION RELEASE To provide more of less thread, loosen nut and adjust stud up or down to suit. Tighten nut securely. Revised 09/2004 e-mail: service@amfreece.cz; parts@amfreece.cz ; website: www.amfreece.com Phones: +420 582 309 146 (Service), +420 582 309 286 (Spare Parts); Fax: +420 582 360 606 1-25
Page 1 and 2: MODEL S-101 EYELET BUTTONHOLE MACHI
Page 3 and 4: LIMITED WARRANTY ON NEW AMF REECE E
Page 5 and 6: S-101 CONTENTS SHEET NO. INSTRUCTIO
Page 7 and 8: S-101 EQUIMENT FAMILIARIZATION Sewi
Page 9 and 10: S-101 STOP MOTION ADJUSTMENTS 101 S
Page 11 and 12: S-101 THREADING DIAGRAMS UPPER SYST
Page 13 and 14: S-101 MODEL 101 - OPERATING INSTRUC
Page 15 and 16: S-101 ADJUSTMENTS THAT DETERMINE TH
Page 17 and 18: ADJUSTMENTS THAT DETERMINE THE CHAR
Page 19 and 20: S-101 MACHINE ADJUSTMENTS - CORRECT
Page 27 and 28: S-101 CUT BEFORE - MACHINE ADJUSTME
Page 29: S-101 CUT BEFORE - MACHINE ADJUSTME
Page 33 and 34: S-101 CORD TRIM - MACHINE ADJUSTMEN
Page 35 and 36: S-101 ADJUSTMENTS FOR THE ADJUSTABL
Page 37 and 38: S-101 NEEDLES Needles for the Reece
Page 39 and 40: S-101 LUBRICATION 1. Red marked pla
Page 41 and 42: TABLE TROUBLESHOOTING OF CONTENTS S
Page 43 and 44: TROUBLESHOOTING S-101 TROUBLE DIGES
Page 45 and 46: TROUBLESHOOTING S-101 4. STITCHING
Page 47 and 48: TROUBLESHOOTING S-101 13. MACHINE S
Page 49 and 50: TROUBLESHOOTING S-101 O) Clamp Foot
Page 51 and 52: TROUBLESHOOTING S-101 29. CHANGING
Page 53 and 54: TROUBLESHOOTING S-101 1. END OF UPP

reece 101 service

Create successful ePaper yourself

Delete template?

Save as template?