quickerbythedozen_bonusprojects
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
®<br />
THIMBLEBERRIES<br />
by LYNETTE JENSEN<br />
Getting Started<br />
• If concerned about colorfastness, test<br />
a 2-inch square of fabric in warm water<br />
to see if dye is released. If so, prewash<br />
and press the fabric.<br />
• If concerned about shrinkage,<br />
prewash and press all the fabric.<br />
• Read instructions thoroughly before<br />
beginning the project.<br />
• For piecing, place right sides of<br />
fabric pieces together and use 1/4-inch<br />
seam allowances throughout unless<br />
otherwise specified.<br />
• It is necessary that accurate<br />
1/4-inch seam allowances are used.<br />
It is wise to stitch a sample 1/4-inch<br />
seam allowance to check your<br />
machine’s seam allowance accuracy.<br />
Bear Paw Burst<br />
• Seam allowances are included in<br />
the cutting sizes given.<br />
• Refer to arrows on diagrams for<br />
pressing direction. If no direction is<br />
specified, press seam toward darker<br />
fabric and/or in the direction that<br />
will create the least bulk.<br />
Bear Paw Blocks<br />
Makes 12 blocks<br />
Cutting<br />
From LARGE FLORAL:<br />
• Cut 2, 4-1/2 x 42-inch strips. From strips cut:<br />
12, 4-1/2-inch squares<br />
• Cut 2, 2-7/8 x 42-inch strips<br />
Step 2 Sew triangle-squares together in pairs; press.<br />
Sew A units to bottom edge of 4-1/2-inch LARGE<br />
FLORAL squares; press. Sew 2-1/2-inch CREAM squares<br />
to right edge of B units; press. Sew B units to right edge<br />
of LARGE FLORAL square; press. At this point each<br />
block should measure 6-1/2-inches square.<br />
From CREAM PRINT:<br />
• Cut 2, 2-7/8 x 42-inch strips<br />
• Cut 1, 2-1/2 x 42-inch strip. From strip cut:<br />
12, 2-1/2-inch squares<br />
Piecing<br />
Stitch diagonally<br />
Trim to 1/4" seam<br />
allowance<br />
Step 1 With right sides together, layer 2-7/8 x<br />
42-inch LARGE FLORAL and CREAM strips. Make 2<br />
layered strips. Press strips together, but do not sew.<br />
Cut layered strips into squares. Cut layered squares<br />
in half diagonally to make 48 sets of triangles. Stitch<br />
1/4-inch from diagonal edge of each triangle set;<br />
press. At this point each triangle-square should<br />
measure 2-1/2-inches square.<br />
Crosscut 24, 2-7/8-inch squares Make 48,<br />
2-1/2-inch<br />
triangle-squares<br />
Make 12<br />
A Units<br />
Press seam open<br />
Sawtooth Borders and Assembly<br />
Cutting<br />
Make 12<br />
B Units<br />
From BLUE PRINT:<br />
• Cut 1, 2-7/8 x 42-inch strip<br />
Make 12<br />
From CREAM PRINT:<br />
• Cut 1, 2-7/8 x 42-inch strip<br />
• Cut 1, 4-1/2 x 42-inch strip. From strip cut:<br />
2, 4-1/2 x 12-1/2-inch top/bottom<br />
outer border strips<br />
• Cut 4, 2-1/2 x 42-inch strips. From strips cut:<br />
2, 2-1/2 x 12-1/2-inch inner border strips.<br />
Diagonally piece the remaining strips together.<br />
From this strip cut:<br />
2, 2-1/2 x 52-1/2-inch side outer border strips<br />
©Copyright 2016 Developed by Thimbleberries, Inc. page 2