We are a wholesale supplier of products, solutions and services in water treatment. We provide only businesses companies such as distributors, retailers, manufacturers and assemblers. A catalog that includes products carefully selected from the most prestigious brands in the Water Treatment market, operative site, personalized services, logistics precise and efficient, flexible organization, but also the basic importance that is attributed to human factors and relationships with partners, are of Sinergroup Srl a reference for many companies of the sector.
Code: 15000411 Elbow overflow 90° / Thread ring 1/2” Code: 15000407 Chlo Active CL2 complete chlorine maker with Titanium electrode, o-ring, Starfit fittings 3/8" OPERATION: Connect the probe on your softener brine line (use the necessary adapters). Check how many liters of resin are there in your softener (look on softener manual). Make sure that the plug of Our generator is disconnected. On the generator's board there is a trimmer that can be setted from 1 to 70 minutes of timer. Every minutes that you program can disinfect 1 lt of resin. The system is ready to start. How it works: The softener during regeneration aspires the brine, our system feels the passage of brine and active electrolysis of NaCl for the time setted on the probe. After this time the generator is silent for 4 hours (ignoring the possible passage of brine). After this 4 hours the system is ready to re-disinfect the resins. The green LED indicates the system voltage, the yellow LED indicates system disinfection. Code: 15000402 Chlo Active CL2 - components chlorine maker Variants Code Description 15000402-01 Chlo Active CL2 chlorine maker without electrode 15000402-02 Titanium electrode for Chlo Active with TEE 3/8'' 13 February 2018 34/72
15000402-03 TEE 3/8'' Replacement parts chlo active Articles to assemble: J173-CPR16IS JG replacement O-ring OD tube 1/2" (x3pcs.) + S001-4200 Straight adaptor OD Tube - M. thread 3/8" x 3/8" (x2pcs.) Code: 15000415 STERIL-SOFT PRO complete chlorine maker IN/OUT 3/8" Automatic disinfection system for water softener from 0 to 350 lt. resin. An automatic chloration of ion exchangers in residential water softeners is already required in most European countries. Even if it is not always compulsory, a periodic chloration is often advised in order to avoid bacteriological growth, which can affect softened water characteristics. The automatic disinfection system for softeners Steril-Soft Pro: * Generates chlorine by brine electrolysis during regeneration. * The chlorine gets in contact with the ion exchange resin at the same time as brine, ensuring regeneration as well as chloration. * Chlorine in excess is eliminated during the regeneration process. * This patented technology generates the electrolysis only during the brine draw cycle and stops automatically based on your own settings: once switched off, the device requires 20 minutes before starting another cycle. * Chlorine production can be set depending on the installation conditions. * We recommend to follow the chart below in order to set the device for the chlorine PPM required by your system. * Steril-Soft Pro can be used with any automatic valve with a 3/8" brine line. * The controller includes its own transformer as well as titanium electrodes. * The electrode cell is installed in the brine line. Feature’s regulation box with cell: * Input voltage 230 VAC ± 10% * Output voltage: 2-6 VDC * Protection: IP44 * Automatic electrode polarization for each cycle. * Potentiometer for the intensity setting adjustable from 0.2 to 2.5 A * Potentiometer for cycle time setting adjustable from 2 to 20 minutes. * Complies with CE regulations 23/73 and 336/89 Feature’s electrode cell: * Titanium electrodes with linking cable. * Fiber glass reinforced polypropylene body. * Connections 3/8" compression fittings Important: the time setting must be smaller than the brine draw cycle time otherwise there is a risk of heating and deterioration of the electronic cell. 13 February 2018 35/72