AG2210 AG2210 | Planetary gear units for AM8000 and AM8500 servomotors Drive Technology 374 The low-backlash, high-performance gear units of the AG2210 series offer high torques, low torsional backlash and up to 16 transmission ratios for optimised drive solutions as well as a very low running noise coupled with maximum quality. The gear units for the AM8000/AM8500 Synchronous Servomotors are mainly used in applications where large mass inertia has to be accelerated, or where the inertia ratio between load and motor prevents dynamic motion. Gears of the AG2210 series are also suitable for use with the motor series AM3xxx. The inertia ratios, the required torques and the suitable motors can be conveniently calculated directly in TwinCAT with the TC Motion Designer. In addition, the tool checks in a single step whether the selected motor can be adapted to the gear unit. The planetary gear units are fitted to the respective motor in the factory and delivered as a complete motor/gear unit. Features – maximum economic efficiency – absolutely maintenancefree, thanks to unique lubrication concept – long service life (> 20,000 h) – high efficiency (> 95 % at full load) – low running noise and smooth operation through maximum production quality – flexible mounting position – output shaft with feather key – 5 sizes LP050…LP155 – 16 gear ratios i = 3, 4, 5, 7, 10 (single-stage), i = 9, 12, 16, 20, 25, 30, 35, 40, 50, 70, 100 (two-stage) – acceleration torque between 13 and 500 Nm – low torsional backlash (≤ 8…13 arcmin) Technical data AG2210 New generation successor of AG2200, identical design Type of gear planetary gear Life span > 20,000 h Coating/surface RAL7016 (grey) Ambient temperature -15…+40 °C Lubrication lubricated for life Installation position variable Protection class IP 64 Mechanically compatible with flange code F (typical combination according to specifications) We reserve the right to make technical changes.
AG2210 Ordering options You will find the possible ordering options for the gear units listed in this table. Please note: The options cannot be retrofitted. Order reference AG2210-+LPaaaS-MFs-i-wX1-Motorsize aaa series/size (050, 070, 090, 120, 155) s = 1 1-stage with i = 3/4/5/7/10 s = 2 2-stage with i = 9/12/16/20/25/30/35/40/50/70/100 i gear ratio w = 0 smooth shaft w = 1 shaft with groove and feather key according to DIN 6885 X identifying letter for clamping hub diameter; not available for selection, is selected automatically based on the respective motor Motorsize Specifies adapter unit between motor and gearbox. Correlates to motor flange code F or flange compatible motor type. Motorsize = AM801x (F1) flange code F1: AM801x; compatible with AM301x Motorsize = AM802x (F2) flange code F2: AM802x; compatible with AM302x Motorsize = AM803x (F3) flange code F3: AM803x, AM853x; compatible with AM303x Motorsize = AM804x (F4) flange code F4: AM804x, AM854x; compatible with AM304x Motorsize = AM805x (F5) flange code F5: AM805x, AM855x Motorsize = AM305x in combination with AM305x Motorsize = AM806x (F6) flange code F6: AM806x, AM856x; compatible with AM306x Motorsize = AM807x (F7) flange code F7: AM807x; compatible with AM307x Drive Technology 375 AG2210 | Size 050 Technical data AG2210-+LP050S-MF1-i AG2210-+LP050S-MF2-i Gear ratio 4/5/7/10 16/20/25/35/50/70/100 Nominal output torque 6…6.5 Nm 6…6.5 Nm Max. acceleration torque 13…14 Nm 13…14 Nm Max. torsion. backlash standard/reduced ≤ 10/– arcmin ≤ 13/– arcmin Typ. flange code F1, F2 F1, F2 AG2210 | Size 070 Technical data AG2210-+LP070S-MF1-i AG2210-+LP070S-MF2-i Gear ratio 3/4/5/7/10 9/12/16/20/25/30/40/50/70/100 Nominal output torque 19…29 Nm 19…29 Nm Max. acceleration torque 37…55 Nm 37…55 Nm Max. torsion. backlash standard/reduced ≤ 8/– arcmin ≤ 10/– arcmin Typ. flange code F2, F3, F4 F2, F3, F4 We reserve the right to make technical changes.