System EP9224-0037 System | Power distribution 4 x EtherCAT P EtherCAT Box 292 The EP9224-0037 enables power distribution from a B17-ENP input to four EtherCAT P ports with B17-ENP forwarding. In each EtherCAT P junction, the current consumption for the control voltage US and the peripheral voltage UP is monitored, limited and if necessary switched off. The input voltage and current values of all outputs can be evaluated via the process data. A 5-pin B17-ENP connector is used for communication with the box and for power supply of power to and with up to 14 A (per US/UP). Several modules can be configured in a cascade arrangement through power forwarding. In case of a short circuit on one of the four outputs or eight voltages (4 x US/4 x UP), this voltage is switched off. The supply for the other junctions remains active. The switch-off or voltage regulation is carried out in such a way that the input voltage does not drop below a critical value. A continuous log of the relevant data can be retrieved in the event of an error. During start-up consumers with large capacities can be added without problem. The diagnostic messages of the individual channels can be read by the master via the EtherCAT interface. Independent switching of individual consumer branches is also possible via the EtherCAT master. Industrial housing Task within EtherCAT system Number of channels Protocol 4-channel power distribution box ENP to EtherCAT P EP9224-0037 coupling to the EtherCAT network, EtherCAT P junction, feed in and monitoring of US and UP IN: 1 x ENP, OUT: 1 x ENP, 4 x EtherCAT P EtherCAT 6 7 4 2 3 1 5 9 8 9 8 4 3 2 4 1 3 5 2 1 6 7 1 | Tx+/GNDS 2 | Rx+/GNDP 3 | Rx-/UP 4 | Tx-/US 1 | Tx+ 2 | Rx+ 3 | Rx- 4 | Tx- 5 | GNDP 6 | PE 7 | UP 8 | GNDS 9 | US +60 °C -25 °C Infeed ENP B17 5-pin, max. 14 A per US/UP (18 A at 30 °C) Power feedthrough ENP B17 5-pin, max. 14 A per US/UP (18 A at 30 °C) Nominal voltage 24 V DC (-15 %/+20 %) Distributed clocks – Current rating per port max. 3 A per US and UP (M8 EtherCAT-P-coded) Data logging recording of relevant data in case of failure Special features input voltages/currents, output currents via process data Operating temperature -25…+60 °C Approvals CE, UL in preparation Further information www.beckhoff.com/EP9224-0037 We reserve the right to make technical changes.
EP9300 System System | PROFINET RT EtherCAT Box The EP9300-0022 EtherCAT Box connects PROFINET RT networks to the EtherCAT Box modules (EPxxxx, EQxxxx and ERxxxx) and converts the telegrams from PROFINET RT to EtherCAT. One station consists of an EP9300- 0022 and any number of EtherCAT Box modules. The box is connected to PROFINET RT via a D-coded M12 socket. With EtherCAT, the PROFINET RT box can use the powerful and ultra-fast I/O system with its large selection of EtherCAT Box modules. The EP9300-0022 supports the PROFINET RT profile and seamlessly fits into PROFINET RT networks. Industrial housing Task within EtherCAT system Number of EtherCAT Box modules Protocol Data transfer rates PROFINET RT EtherCAT Box EP9300-0022 coupling of standard digital and analog EtherCAT Box modules to PROFINET RT networks depending on the process data size PROFINET RT 10/100 Mbaud EtherCAT Box 293 +60 °C 4 3 2 1 1 | Tx+ 2 | Rx+ 3 | Rx- 4 | Tx- -25 °C 1 4 2 3 1 | Tx+ 2 | Rx+ 3 | Rx- 4 | Tx- SHLD | Shield PROFINET EtherCAT Nominal voltage 24 V DC (-15 %/+20 %) Bus interface 2 x M12 socket, D-coded (switched) Type/number of depending on the process data size peripheral signals Configuration automatic Power supply 24 V DC (-15 %/+20 %) Electrical isolation 500 V Special features potted, shock- and vibration-resistant Operating temperature -25…+60 °C Approvals CE, UL Further information www.beckhoff.com/EP9300 We reserve the right to make technical changes.