Views
5 months ago

V27 Software Guide Pulpmatic Ultima Eco Uno Incomatic V1.7

A2 - Machine start

A2 - Machine start options for V17 - V27 Foot cup sensor to open the lid Hands-free Start Options 02 I.R. hands free start only Automatic lid close after A7 (value in seconds) Lid close buzzer enabled 34 00 As per option 02 above Auto lid close enabled (A7) - Lid close buzzer disabled As per option 02 above Auto lid close disabled Foot cup sensor to open the lid Foot cup Start Options 03 Foot cup sensor activated a second time will start the cycle (IR hand sensor may also be used to start) Automatic lid close after A7 (value in seconds) Lid close buzzer enabled 35 01 As per option 03 above Auto lid close enabled (A7) - Lid close buzzer disabled As per option 03 above Auto lid close disabled Fully Automatic Start Options Full automated cycle triggered by single foot cup; lid open, lid close and start cycle from single activation of foot cup Auto lid open after A6 value in seconds (if speaker fitted this option delays lid to hear speaker; option may not suit all users) 10 Auto lid close after A7 (value in seconds) Do not set less than 10 seconds, users may be uncomfortable with less time Machine auto starts without need to activate hands free proximity sensor (IR hand sensor may also be used to start) Lid close buzzer enabled 42 As per option 10 above Auto lid close enabled (A7) - Lid close buzzer disabled Copyright © 2017 DDC Dolphin Ltd. Page 12 of 47 February 18 SGPv27 – V1.7

10. Guide to parameter settings Maintenance count This parameter defines the service due date, this is measured by the number of completed cycles. A defined number of cycles are set by this parameter, the machine counts down from this number: • 50 = 5000 cycles, after 100 cycles the count is reduced by 1 • 49 = 4900 cycles, after 100 cycles the count is reduced by 1 When the count reaches 00 the display will show F4, this alert message means a service visit is required. The machine can still be operated as normal with an F4 alert on the display. To clear the F4 press and hold the PCB reset switch SW2 or SW4 – please see the next section (Amending the parameter settings) to identify your PCB and relevant reset switch: The current cycle count can be viewed by turning the power OFF and back on again, the number in the display represents the number of cycles left before the machine generates the F4 service required alert. Hands-free IR proximity sensitivity The Pulpmatic range of machines are fitted with an IR (infra-red) hands free proximity sensor located below the green “Start” icon on the display. Holding your hand over this sensor will put the machine into cycle. This IR (infra-red) sensor is only active when the water tank is full and the lid has been opened. From V22 the hands free sensor is active if water tank is not yet full. Previous versions of software require the water tank to be full before hands free sensor becomes active. The IR (infra-red) sensor remains active if the auto-start function is selected. The IR (infra-red) sensitivity MUST be calibrated once the machine has been installed, this MUST be done on every machine. The IR (infra-red) sensor may be affected by natural or man-made sources of infra-red light, (room lighting for example). If the setting is too sensitive the sensor will self-activate. If the setting is too low the sensor will not be triggered by the operator. The sensor should activate with the hand 25mm to 50mm away from the surface of the “start” sensor. Copyright © 2017 DDC Dolphin Ltd. Page 13 of 47 February 18 SGPv27 – V1.7

A Leader's Guide to Agile Business - Rally Software
Medical Office Software Guide
WinAlign® Software
License Administration Guide - Sonnet Software
Agile Development, DevOps and achieving ... - Rally Software
Geovision NVR Software Feature Guide - Use-IP
Product datasheet: Sony SNC-DH240T - Network Webcams
software validation - Pharsight Corporation
TerraExplorer Quick Start Guide - Skyline Software Systems
SNC-CH220 - Sony Professional Solutions Asia Pacific
Camera IP HD de tip bullet Sony SNC-CH160 - GTO Security ...
EtherLogic Ultima Controller - Industrial Control Links
Polycom UC Software Administrators' Guide
Polycom UC Software Administrators' Guide - 4.1.0
JideFX Common Layer Developer Guide - JIDE Software