7 months ago

Software Guide V27 - Panamatic Mini, Midi, Optima 2 v1.6

3. Cautionary notes

3. Cautionary notes Failure to comply with the instructions and recommendations contained within this guide may impair the safe operation and reliability of the machine. It may also invalidate the warranty of the Pulpmatic unit. This machine should only be used for the purpose for which it was designed. Caution, when handling the detergent chemicals used by the machine, it is recommended that PPE is worn such as gloves and eye protection to prevent contact with skin and eyes. Only use chemicals or detergents supplied or approved by DDC Dolphin Ltd. DO NOT start the machine until it has been commissioned by a trained DDC Dolphin Ltd agent. If the machine is started without commissioning, this will damage the machine and invalidate the warranty. DO NOT obstruct the movement of the lid or place anything around the top of the chamber to prevent the lid closing. Always isolate the electrical supply to the machine before opening the front panel IMPORTANT The hands free IR (Infra-red) sensor must be calibrated before the machine is used by the client (Parameter A1) Copyright © 2017 DDC Dolphin Ltd. Page 4 of 41 Feb 18 SGPana – V27 1.6

4. Release notes Revision Notes Suitable for V11 Revised PCB Mini, Midi & Optima 2 V12 & V13 Never released N/A V14 24 Hour pump run & disinfection temperature level settable features added Mini, Midi & Optima 2 V15 Change from motorised locks to Southco locks Mini, Midi & Optima 2 V16 Never released N/A V17 Patlite audio system introduced, new lid open lid close time settings, 5 second delay introduced to water solenoid when float switch first activates to compensate for high water pressure environments. Function to auto start the machine from foot cup activation only. (Machine start option parameter) Mini, Midi & Optima 2 V18 & V19 Never released N/A V20 Pulpmatic’s Only – No change Mini, Midi & Optima 2 N/A V21 V22 Pulpmatic’s Only – No change Mini, Midi & Optima 2 New feature added to enable hands free start if water tank not full. Lid will close and machine will start automatically once water tank has completed filling Corrections & enhancements to A2 start options N/A Mini, Midi & Optima 2 V23 V24 Bug fix for foot cup start feature A2 Ultima basic cycle time can be reduced to 100 seconds (AE = 0), this becomes an Eco cycle NOT suitable for Optima 2 bedpan washer (use V25 or higher) Corrections & enhancements to A2 start options This software is only used on the Ultima built with an Uno PCB Corrections & enhancements to A2 start options Ultima, Uno, Pulp+ & Eco Ultima built with Uno PCB ONLY Canada & Japan Copyright © 2017 DDC Dolphin Ltd. Page 5 of 41 Feb 18 SGPana – V27 1.6

cNODE® Transponders Maxi, Midi and Mini - Kongsberg Maritime
Kategorie mini midi maxi maxi 2 Modell HP 2170p ... - u:book
Line 6 PODStudio & TonePort MIDI Setup Guide (Rev 2 ... - Thomann
Vernier LabQuest Mini User's Manual - Vernier Software & Technology
YOTTA Mini Software installation guide(5914KB) - Axus
Yotta Mini Sport Software installation guide - Axus
Vision MINI Smart Camera Quick Start Guide - Microscan
Samsung Galaxy Mini 2 S6500D Unlock Software - GalaxyUnlocker
Samsung Galaxy Mini 2 S6500L Unlock Software - GalaxyUnlocker
Line 6 FBV MkII Advanced User Guide, English (Rev. 2)
User Guide for Alliance Planner Programming Software - UniMac
WinTEC3 Software user's Guide - Electromotive Engine Controls
MONOPACK 2 Manual - Pro/Motion Mechanik + Elektronik + Software
Installer's handbook - 1/3 Types of installation - 2/3 Software guide ...