Views
3 months ago

construction chemicals

Mantotherm Primer

Mantotherm Primer Acrylic Emulsion Based Thermal Insulation Primer PRODUCT DESCRIPTION Highly adhesive, acrylic emulsion based, opaque, white, solvent-free primer with filling. AREAS OF USE Mantotherm Primer is used in order to enhance adherence and reduce consumption under siding and paint on cement based, plastered surfaces. PRODUCT ADVANTAGES • Enhances the adherence between the surface, on which it is applied, and the siding/ coating and the paint to be applied thereafter. • Stabilizes the surface absorbance. • Poses high covering capability. • Applied easily and rapidly. • Solvent free and environmentally friendly. REFERENCE STANDARDS Certifications/Standards TSE K 208 Ministry of Public Works and Settlement Item No. Ministry of Public Works and Settlement Item No.: 04.503/1 QUALITY CERTIFICATES Conformant to TSE K 208. CE APPLICATION PROCEDURE Application Surfaces Indoors and Outdoors Walls; - Cement based plaster Surface Preparation Application surfaces should be sound, clean, dust free, and free from molding oils and other foreign substances. Such materials as mortar and cement residues should be peeled off. Application Methods Prior to application, by weight 1/1 ratio, diluted with clean water, should be applied by brush or roller in a single coat. Application Recommendations • Any foreign material should not be added into the product during the application. • Any extra water should not be added to the mixture. • The product should not be applied on unsound surfaces. The soundness and the load bearing capacity of old surfaces should be checked prior to adhesion. • The surface should be preserved from air currents and water contact during and after the application. • The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing. • Due care should be given to prevent the exposure of the material to direct sunlight in hot weather conditions. • The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance. • The product should not be applied in rainy weather conditions, and the application surface should be preserved from rain for a period of 24 hours. • Refer to our technical support hotline for recommendation on different surface applications. (PHONE: 444 4 595) Mixing Period Mantotherm Primer is, upon being diluted with water by 1/1 in terms of weight, stirred for 2 to 3 minutes with a low speed mixer until it becomes a homogenous mixture. The product should be kept homogenous by stirring it intermittently during the application. Application Equipment • Brush • Roller Equipment Cleaning The equipment used should be cleaned with water following the application before the product dries. TECHNICAL PROPERTIES Chemical Structure: Acrylic emulsion based primer with filling Density: 1.60 ± 0.1 gr/cm 3 pH: 7 - 9 Coat Thickness: Single coat Color: White CONSUMPTION Recommended consumption amount for a single coat application on 1 m 2 surface is 0.10 - 0.15 kg. The said value may vary, depending on the surface and ambient conditions. PACKAGING Mantotherm Primer is delivered in net 25 kg plastic buckets. SHELF LIFE The shelf life of the product is 12 months when stored within non-tampered original packaging in dry (maximum relative humidity 60 %) and cool (ambient temperature between +5°C and +25°C) environment. STORAGE CONDITIONS The product should be stored within non-tampered original packaging in dry (maximum relative humidity 60 %) and cool (ambient temperature between +5°C and +25°C) environment. It should not be exposed to direct sunlight. The container of the product should be closed firmly when not used. SAFETY PRECAUTIONS Please refer to the Safety Data Sheet (SDS) as appropriate for easy and safe application. 137 Surface and Ambient Temperature The surface and ambient temperature should be between +5°C and +30°C whilst at application. Application Limits Required stand by period for decorative coating and paint application The foregoing values represent the results of the laboratory tests conducted at 23 ± 2°C temperature and 50% ± 5 relative humidity conditions. The values provided as per the table may vary depending on the surface and ambient conditions. APPLICATION INSTRUCTIONS Mixing Ratio The product should be mixed with water, weighing equal to 100 % of the product. (25 liters of water for a 25 kg package) Mixing Equipment • Low speed electrical mixer (400 cycles/min.) • Special tip stirring equipment Minimum 12 hours

Mantotherm Dekominera - Grain Texture Mineral Based Decorative Coating With Grain Texture G PRODUCT DESCRIPTION White cement based, fiber reinforced surface finishing coat, which creates a natural texture on the surface. AREAS OF USE Mantotherm Dekominera - Grain Texture can be safely applied as the finishing coat on cement based fine plaster or thermal insulation systems in outdoors spaces. The product is also suitable for use on interior walls for decorative purposes. PRODUCT ADVANTAGES • Prevents the formation of cracks and spalling thanks to the fibers in its content. • Provides the structure with a natural and decorative appearance. • Prevents condensation and winds the system thanks to its high vapor permeability. • Resistant to external weather conditions and is water repellant. • Suitable for house paint application thereon. • Prepared and applied easily. PERFORMANCE Gloss Class G3 TS 4318 EN ISO 2813 Dry film thickness Class E5 TS EN 1062 - 1 Grain size Class S4 TS 2585 Water vapor transmission rate Class V2 TS EN ISO 7783 - 2 Water transmission rate Class W2 TS EN 1062 - 3 The foregoing values represent the results of the laboratory tests conducted at 23 ± 2°C temperature and 50% ± 5 relative humidity conditions. The values provided as per the table may vary depending on the surface and ambient conditions. REFERENCE STANDARDS Certifications/Standards TS 7847 ETAG 004 Ministry of Public Works and Settlement Item No. Ministry of Public Works and Settlement Item No.: 04.476/A QUALITY CERTIFICATES TSE G ETA APPLICATION PROCEDURE Application Surfaces Indoors and Outdoors Walls; - Fine plastered surfaces - Thermal insulation systems Surface Preparation • Mantotherm Dekominera - Grain Texture shall be applied minimum 12 hours after the application of Mantotherm Primer application on such floors, on which Mantotherm Plaster Mortar or MegaSıva Thermo prior to such primer application. Application Methods • The homogenous mixture to be prepared should be applied to the surface smoothly and properly with a stainless steel trowel. • Any surplus material should be peeled off the surface during the application in order to ensure a homogenous and smooth surface. • Once the decorative coating is applied homogenously on the application surface, the pattern design should be performed within 10 minutes at maximum. • Design patterns should be created with a plastic trowel on the surface by way of circular motion in order to create the graine texture. The surface of the trowel should be peeled off frequently during the pattern design. Application Recommendations • The painting application should not be initiated before minimum 7 days following the mineral based grain texture decorative coating application. • The product should, once mixed, be used before the expiration of its pot life. Any mortar, the pot life of which has expired, should not be used during the application. • Any such foreign substance as lime, cement or plaster should not be added to the mortar prepared. • Any extra water should not be added to the mixture. • The surface should, subsequent to application, be protected from water and frost until it dries completely. • The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing. • Due care should be taken to ensure that the material is not exposed to direct sunlight in hot weather conditions, and the product should be mixed with cold water. • The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance. • The product should not be applied in rainy weather conditions, and the application surface should be preserved from rain for a period of 24 hours. • Refer to our technical support hotline for recommendation on different surface applications. (PHONE: 444 4 595) Surface and Ambient Temperature The surface and ambient temperature should be between +5°C and +30°C whilst at application. Application Limits Useful time for prepared mortar - Pot life Pattern design The foregoing values represent the results of the laboratory tests conducted at 23 ± 2°C temperature and 50% ± 5 relative humidity conditions. The values provided as per the table may vary depending on the surface and ambient conditions. APPLICATION INSTRUCTIONS Mixing Ratio The product should be mixed with water, weighing equal to 24 - 26 % of the product. (6.0 - 6.5 liters of water for a 25 kg package) Mixing Equipment • Low speed electrical mixer (400 cycles/min.) • Special tip stirring equipment Mixing Period The mortar will not embrace the water instantly upon the addition of water due to the water repellant additives it inherently includes. The product should be stirred with a low-speed mixer until any dry dust and globs are eliminated. The mortar should, then, be stirred once again for 1 to 2 minutes after being had settled for 3 to 4 minutes following preparation. Application Equipment • Steel trowel • Smoothing trowel Maximum 2 hours Maximum 10 minutes Equipment Cleaning The equipment used should be cleaned with water following the application before the mortar dries. TECHNICAL PROPERTIES Chemical Structure: White cement based decorative coating, containing fiber and water repellant additives Dry Density: 1.65 ± 0.1 gr/cm 3 Mortar Density: 1.80 ± 0.1 gr/cm 3 Grain Size: ≤ 2000 µm Coat Thickness: Maximum 2.5 mm Color: White CONSUMPTION Recommended consumption amount for application on 1 m 2 surface is 3.0 - 3.5 kg. The said value may vary, depending on the surface and ambient conditions. PACKAGING Mantotherm Dekominera - Grain Texture is delivered in net 25 kg kraft bags, which are stowed in 54 pcs. on 80 cm x 100 cm palettes (1350 kg). SHELF LIFE The shelf life of the product is 12 months as of the date of production if stored within non-tampered original packaging in dry (maximum relative humidity 60 %) and cool (ambient temperature between +5°C and +25°C) environment. STORAGE CONDITIONS The product should be stored within non-tampered original packaging in dry (maximum relative humidity 60 %) and cool (ambient temperature between +5°C and +25°C) environment. It should not be exposed to direct sunlight. The container of the product should be closed firmly when not used. SAFETY PRECAUTIONS Please refer to the Safety Data Sheet (SDS) as appropriate for easy and safe application. 138

Nanotechnology and Construction
Module 4 - Construction of a gravity fed system
Mapecem Premix Mapecem Premix - Northland Construction Supplies
PIPELINE REHABILITATION – PROTEGOL ... - TIB Chemicals AG
Flooring Systems Brochure Download (938Kb) - Triton Chemicals
Applying An External Chemical Stimulus
Paver Reneu Bro 8.5x11 - Vexcon Chemicals
TEX•COTE® XL-70® BRIDGE•COTE® Brochure - Textured ...
Planicrete AC Planicrete AC - Northland Construction Supplies
Disaster Resistant Construction Practices - Shelter Centre
Chemicals For Sustainable Construction - Roof & Facade
Vandex Protects Drinking Water
23. masses, paints, chemicals, papers
Mapelastic Smart Mapelastic Smart - Specialtyproducts.net
En Büyük Seramik Fuarı Cersaie'de - Seramik Federasyonu
Choose The Right Cement Brochure - Lafarge in South Africa
Buildcrete Brochure - Lafarge in South Africa