Views
8 months ago

O & M Manual

Installing the Mat

Installing the Mat (Continued) Step 5 - Install floor sensor 5 Place the floor sensor below the fibreglass mesh. The floor sensor must be installed centrally between the two runs of heating element and should extend a minimum of 150mm into the heated area. Secure the sensor to the floor using tape. NOTE: DO NOT TAPE OVER THE SENSOR TIP. It is best to avoid placing the floor sensor in areas of heat fluctuations e.g. near hot water pipes or radiators. It may be necessary to cut a channel in the floor to ensure that the floor sensor and power supply cable are kept at the same height as the heating element. When installing the floor sensor (located in the thermostat box) DO NOT cross over or under the heating element. 6 At this stage the floor sensor must also be tested. Check the resistance of the floor sensor using your multi-meter (20K ohms). You should get a reading of approximately 9-23K ohms depending on the room temperature. If you do not get a reading your floor sensor may be damaged. If this is the case call the Warmup Technical Helpline to request a replacement. NOTE: The sensor may be extended up to 50m. Step 6 - Fit Power Leads Each mat is fitted with a single power lead for connecting the mat to the thermostat. To ensure the power lead remains at the same level as the heating element, you may need to cut or chisel a channel in the subfloor. When doing this take care not to damage the heating element. Secure the power lead in place using tape but do not tape over the manufactured joint where the power supply cable meets the heating element. 7 The power lead will go into the electrical trunking/conduit up to the thermostat. It is possible to extend the power lead using twin and earth cable. NOTE: Instructions for fitting the Warmup® thermostat are included in the thermostat box. Step 7 - Tile & grout the floor Ensure you use tile adhesives and grouts suitable for use with underfloor heating systems (they must contain a flexible additive). It is important that each tile is solidly bedded in adhesive, with no air gaps or voids beneath. (2 Part Flexible Adhesive). Do NOT dot and dab the tiles. Check with the manufacturers of the adhesive to ensure suitability. Use a plastic notched trowel to move the adhesive along the element. Use a piece of cardboard on top of the exposed element to use as a crawl board. Ensure to test the resistance of the heating mat regularly during tiling to check the mat hasn’t been damaged during tiling. If using flexible levelling compound before tiling make sure that the mat is completely flat, extra tape can be used to secure the edges of the fibre glass mesh to the floor. Do not store tiles or heavy objects on the mat while tiling. Wait for 8 days to allow the adhesive to dry before you switch on the system. FINALLY TEST THE RESISTANCE OF THE HEATER(S) ONCE TILING IS COMPLETE. 8

Warranty Terms and conditions apply Models: DWS heaters, PFM and SPM heaters manufactured by Warmup Plc. THE LIFETIME ELEMENT OF THIS GUARANTEE DOES NOT EXTEND TO THERMOSTATS WHICH ARE COVERED BY SEPARATE GUARANTEES. THIS GUARANTEE DOES NOT AFFECT YOUR STATUTORY RIGHTS. Warmup® Underfloor Heater is guaranteed by Warmup plc (“Warmup”) to be free from defects in materials and workmanship under normal use and maintenance, and is guaranteed to remain so subject to the limitations and conditions described below. The UNDERTILE HEATER is guaranteed for the LIFETIME of the floor covering under which it is fitted, except as provided below (and your attention is drawn to the exclusions listed at the end of this guarantee). This lifetime guarantee applies: 1. only if the unit is registered with Warmup within 30 days after purchase. Registration can be completed online at www. warmup.co.uk. In the event of a claim, proof of purchase is required, so keep your invoice and receipt - such invoice and receipt should state the exact model that has been purchased; and 2. only if the heater has been earthed and protected by a Residual Current Device (RCD) at all times. Thermostats are guaranteed for a period of 3 YEARS from the date of purchase, except as provided below. The guarantee for the Warmup 3Ie thermostat can be upgraded to lifetime. Contact Warmup for details 0845 345 2288. Neither guarantee continues if the floor covering over the heater(s) is damaged, lifted, replaced, repaired or covered with subsequent layers of flooring. The guarantee period begins on the date of purchase. During the period of the guarantee Warmup will arrange for the heater to be repaired or (at its discretion) have parts replaced free of charge. The cost of the repair or replacement is your only remedy under this guarantee which does not affect your statutory rights. Such cost does not extend to any cost other than direct cost of repair or replacement by Warmup and does not extend to costs of relaying, replacing or repairing any floor covering or floor. If the heater fails due to damage caused during installation or tiling, this guarantee does not apply. It is therefore important to check that the heater is working (as specified in the installation manual) prior to tiling. WARMUP PLC SHALL IN NO EVENT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO EXTRA UTILITY EXPENSES OR DAMAGES TO PROPERTY. WARMUP PLC is not responsible for: 1. Damage or repairs required as a consequence of faulty installation or application. 2. Damage as a result of floods, fires, winds, lightening, accidents, corrosive atmosphere or other conditions beyond the control of Warmup plc. 3. Use of components or accessories not compatible with this unit. 4. Products installed outside the United Kingdom. 5. Normal maintenance as described in the installation and operating manual, such as cleaning thermostat. 6. Parts not supplied or designated by Warmup. 7. Damage or repairs required as a result of any improper use, maintenance, operation or servicing. 8. Failure to start due to interruption and/or inadequate electrical service. 9. Any damage caused by frozen or broken water pipes in the event of equipment failure. 10. Changes in the appearance of the product that does not affect its performance. TM SafetyNet Installation Guidelines: If you make a mistake and damage the new heater before laying the floor covering, return the damaged heater to Warmup within in 30 days along with your original dated sales receipt. WARMUP WILL REPLACE ANY PRE-TILED HEATER (MAXIMUM 1 HEATER) WITH ANOTHER HEATER OF THE SAME MAKE AND MODEL - FREE. Please note: (i) Repaired heaters carry a 5 year warranty only. Under no circumstances is Warmup responsible for the repair or replacement of any tiles / floor covering which may be removed or damaged in order to affect the repair. (ii) The SafetyNet TM Installation Guarantee does not cover any other type of damage, misuse or improper installation due to improper adhesive or subfloor conditions. Limit of one free replacement heater per customer or installer. (iii) Damage to the heater that occurs after tiling, such as lifting a damaged tile once it has set, or subfloor movement causing floor damage, is not covered by the SafetyNet TM Guarantee. Register your Warmup® warranty online at www.warmup.co.uk 9

  • Page 1 and 2:

    Health & Safety File including Oper

  • Page 3 and 4:

    Health & Safety File Introduction T

  • Page 5 and 6:

    Health & Safety File Health and Saf

  • Page 7 and 8:

    Health & Safety File Description of

  • Page 9 and 10:

    Health & Safety File Material Suppl

  • Page 11 and 12:

    Quote 1055856 Customer name: Graham

  • Page 13 and 14:

    Quote 1056741 Customer name: Graham

  • Page 15 and 16:

    Health & Safety File Drawings and S

  • Page 17 and 18:

    Ivy Cottage Bathrooms Fixtures and

  • Page 19 and 20:

    Ivy Cottage Bathrooms Fixtures and

  • Page 21 and 22:

    Ivy Cottage Bathrooms Fixtures and

  • Page 23 and 24:

    Ivy Cottage Bathrooms Fixtures and

  • Page 25 and 26:

    Ivy Cottage Bathrooms Fixtures and

  • Page 27 and 28:

    Ivy Cottage Paints and Wall Paper S

  • Page 29 and 30:

    Ivy Cottage Paints and Wall Paper S

  • Page 31 and 32:

    Ivy Cottage Paints and Wall Paper S

  • Page 33:

    Health & Safety File Certification

  • Page 44 and 45:

    Riverside Environmental Services Lt

  • Page 46 and 47:

    Job No: J112167 Section 1: Executiv

  • Page 48 and 49:

    Job No: J112167 Locations containin

  • Page 50 and 51:

    Job No: J112167 Section 2: Contact

  • Page 52 and 53:

    Job No: J112167 3.1.1 Description,

  • Page 54 and 55:

    Job No: J112167 G.02 Store Cupboard

  • Page 56 and 57:

    Job No: J112167 1.07 Shower Room Iv

  • Page 59:

    Job No: J112167 Sample number Locat

  • Page 62 and 63:

    Job No: J112167 Sample N o Location

  • Page 64 and 65:

    Job No: J112167 Sample N o VC CE001

  • Page 66 and 67:

    Job No: J112167 Section 7: Appendic

  • Page 68 and 69:

    Job No: J112167 IV - Certificates o

  • Page 70:

    Job No: J112167 V - Site Drawings P

  • Page 78 and 79:

    Job No: J112167 VII - Glossary of T

  • Page 80 and 81:

    Health & Safety File Operation, Car

  • Page 90 and 91:

    Health & Safety File QBS Electrical

  • Page 92 and 93:

    CONTENTS INTRODUCTION 1 HEALTH & SA

  • Page 94 and 95:

    ELEC O&M Ivy Cottage SECTION 2 HEAT

  • Page 96 and 97:

    ELEC O&M Ivy Cottage Accidents Invo

  • Page 98 and 99:

    ELEC O&M MANUAL: Ivy Cottage SECTIO

  • Page 100 and 101:

    FAULT FINDING/PERIODIC TEST AND EME

  • Page 102 and 103:

    EMERGENCY LIGHTING QBS ELECTRICAL L

  • Page 104 and 105:

    SMALL POWER QBS ELECTRICAL LTD 168

  • Page 106 and 107:

    ELEC O&M MANUAL: Ivy Cottage SECTIO

  • Page 108 and 109:

    ELEC O&M MANUAL: Ivy Cottage SECTIO

  • Page 110:

    QBS ELECTRICAL LTD 168 Whitton Aven

  • Page 120:

    ELEC O&M MANUAL: Ivy Cottage SECTIO

  • Page 123 and 124:

    DATA SHEET: UCL series ISSUE: BADEC

  • Page 125 and 126:

    Crown Flooring Operation & Maintena

  • Page 127 and 128:

    5. Cleaning and Maintenance Registe

  • Page 129 and 130:

    Registered in England and Wales: Co

  • Page 131 and 132:

    Registered in England and Wales: Co

  • Page 133 and 134:

    Registered in England and Wales: Co

  • Page 136 and 137:

    Heat 45 & 55 User Instructions FAN

  • Page 138 and 139:

    1 BOILER CONTROLS / DISPLAY 1st STA

  • Page 140 and 141:

    To shut Down the Boiler 1. For shor

  • Page 142 and 143:

    Keston Heat - User’s 7

  • Page 144 and 145:

    Health & Safety File Cambridge Stov

  • Page 146 and 147:

    CONTENTS INDEX: WARRANTY………

  • Page 148 and 149:

    PLEASE READ THESE INSTRUCTIONS PRIO

  • Page 150 and 151:

    REMOVING INTERNAL COMPONENTS All in

  • Page 152 and 153:

    RE-ASSEMBLING THE STOVE Front Dimen

  • Page 154 and 155:

    LEGAL REQUIREMENTS Hunter Stoves Gr

  • Page 156 and 157:

    COMMISSIONING & HANDOVER APPLIANCE

  • Page 158 and 159:

    B) To operate pull the air control

  • Page 160 and 161:

    FIREBRICKS In normal use, these can

  • Page 162 and 163:

    OPERATION SMOKE PROBLEMS ADVERSE WE

  • Page 164 and 165:

    STOVE CARE PRODUCTS All replacement

  • Page 166 and 167:

    BODY ASSEMBLY SPARES ASPECT COMPACT

  • Page 168 and 169:

    SERVICE RECORDS 1 st Service Date o

  • Page 170 and 171:

    For both Solid Fuel and Gas Stoves:

  • Page 172 and 173:

    CONTENTS INDEX: WARRANTY………

  • Page 174 and 175:

    PLEASE READ THESE INSTRUCTIONS PRIO

  • Page 176 and 177:

    REMOVING INTERNAL COMPONENTS All in

  • Page 178 and 179:

    RE-ASSEMBLING THE STOVE Refit all t

  • Page 180 and 181:

    comply with current Building Regula

  • Page 182 and 183:

    COMMISSIONING & HANDOVER APPLIANCE

  • Page 184 and 185:

    B) To operate pull the air control

  • Page 186 and 187:

    FIREBRICKS In normal use, these can

  • Page 188 and 189:

    OPERATION SMOKE PROBLEMS ADVERSE WE

  • Page 190 and 191: STOVE CARE PRODUCTS All replacement
  • Page 192 and 193: BODY ASSEMBLY SPARES ASPECT 5 SLIML
  • Page 194 and 195: SERVICE RECORDS 1 st Service Date o
  • Page 196: For both Solid Fuel and Gas Stoves:
  • Page 200 and 201: R and N Construction 135 Sunnymead
  • Page 202 and 203: 7 YEAR LIFE CARBON MONOXIDE POISONO
  • Page 204 and 205: CONTENTS Features 4 Carbon monoxide
  • Page 206 and 207: CO enters the body through the lung
  • Page 208 and 209: WARNING: This carbon monoxide detec
  • Page 210 and 211: WHERE TO INSTALL YOUR DETECTOR This
  • Page 212 and 213: In addition to the above the follow
  • Page 214 and 215: To mount on a wall or ceiling: Plea
  • Page 216 and 217: This should be continued for the li
  • Page 218 and 219: test for the sounder, power pack an
  • Page 220 and 221: 15cm (6”) Step 4 Turn the detecto
  • Page 222 and 223: • Within 3 minutes when exposed t
  • Page 224 and 225: WHAT TO DO IN THE EVENT OF AN ALARM
  • Page 226 and 227: The alarm will sound: • Between 6
  • Page 228 and 229: This warranty does not affect your
  • Page 230 and 231: Electrical WARNING - THIS APPLIANCE
  • Page 232 and 233: Energy Saving Tips The energy we us
  • Page 234 and 235: Technical Information SPM 150W/m²
  • Page 236 and 237: Do’s and Don’ts DO Carefully re
  • Page 238 and 239: Electrical Safety Considerations As
  • Page 242 and 243: Control Card Place this card in a v
  • Page 244: Warmup plc., United Kingdom 702 & 7
  • Page 247 and 248: Contents Contents Safety informatio
  • Page 249 and 250: Safety information Congratulations
  • Page 251 and 252: Safety information 4. If the supply
  • Page 253 and 254: Safety information This appliance s
  • Page 255 and 256: Safety information Do not let child
  • Page 257 and 258: Safety information • The liquid d
  • Page 259 and 260: Safety information Instructions abo
  • Page 261 and 262: Installation Spanner Bolt caps Hose
  • Page 263 and 264: Installation Installation Flooring
  • Page 265 and 266: Installation STEP 3 Adjust the leve
  • Page 267 and 268: Installation 8. Connect the other e
  • Page 269 and 270: Installation STEP 5 Position the dr
  • Page 271 and 272: Before you start Initial settings R
  • Page 273 and 274: Before you start STEP 6 Apply a pro
  • Page 275 and 276: Before you start NOTE The actual ap
  • Page 277 and 278: Before you start To use liquid dete
  • Page 279 and 280: Operations Operations Press to chan
  • Page 281 and 282: Operations Cycle overview Standard
  • Page 283 and 284: Operations Options Option Pre Wash
  • Page 285 and 286: Operations Settings Child Lock To p
  • Page 287 and 288: Maintenance Smart Check To enable t
  • Page 289 and 290: Maintenance Cleaning Surface of the
  • Page 291 and 292:

    Maintenance Detergent drawer A 1. W

  • Page 293 and 294:

    Troubleshooting Checkpoints If you

  • Page 295 and 296:

    Troubleshooting Troubleshooting Sto

  • Page 297 and 298:

    Troubleshooting Information codes I

  • Page 299 and 300:

    Troubleshooting Code AC6 Action Che

  • Page 301 and 302:

    Specifications Protecting the envir

  • Page 303 and 304:

    Specifications Power consumption Ty

  • Page 305 and 306:

    Specifications According to Regulat

  • Page 307 and 308:

    Specifications According to Regulat

  • Page 309 and 310:

    Specifications According to Regulat

  • Page 311 and 312:

    Memo Untitled-1 66 2017-06-26 3:17:

  • Page 313 and 314:

    QUESTIONS OR COMMENTS? COUNTRY CALL

  • Page 315 and 316:

    Contents Contents Safety informatio

  • Page 317 and 318:

    Safety information Congratulations

  • Page 319 and 320:

    Safety information 7. For use in Eu

  • Page 321 and 322:

    Safety information Safety informati

  • Page 323 and 324:

    Safety information When gas (city g

  • Page 325 and 326:

    Safety information • This may res

  • Page 327 and 328:

    Installation Accessories (supplied)

  • Page 329 and 330:

    Installation Location requirements

  • Page 331 and 332:

    Installation Drain hose (if necessa

  • Page 333 and 334:

    Installation By using the drain pip

  • Page 335 and 336:

    Installation 2. Use a thin object t

  • Page 337 and 338:

    Installation 8. Remove the 2 screws

  • Page 339 and 340:

    Installation 2. Remove 2 screws (A)

  • Page 341 and 342:

    Installation 8. Move the bottom scr

  • Page 343 and 344:

    Operations Displays all cycle infor

  • Page 345 and 346:

    Operations Cycle overview Operation

  • Page 347 and 348:

    Operations Cycle chart NOTE For bes

  • Page 349 and 350:

    Operations Rack Dry (applicable mod

  • Page 351 and 352:

    Operations Cycle guide Always follo

  • Page 353 and 354:

    Maintenance WARNING • Do not clea

  • Page 355 and 356:

    Maintenance Water tank To avoid lea

  • Page 357 and 358:

    Maintenance 4. Clean the heat excha

  • Page 359 and 360:

    Troubleshooting Symptom Lint on clo

  • Page 361 and 362:

    Appendix Iron dry or steam temperat

  • Page 363 and 364:

    Appendix DV9*M50****, DV8*M50****,

  • Page 365 and 366:

    Appendix Sheet of household tumble

  • Page 367 and 368:

    Appendix NOTE 1. Energy consumption

  • Page 369:

    QUESTIONS OR COMMENTS? COUNTRY CALL

Isolator Row O&M Manual
GRUNFOS FIRE SYSYTEMS O & M MANUALS - Xact
a f m o a f m o o
Grease Interceptor O & M Manual (PDF) - National Precast Concrete ...
l ’ O l m o
Electronic O&M Manuals Information at Your ... - NC AWWA-WEA
O wners M anual
SMUD O&M Experience
M A N G O
O wners M anual
O verlay M u lticast M o b ility
A V O F A R M
M A T I O N
M O S T Y
S A M M O D E
M O S T Y