AUTOCAD 2015 AND INVENTOR TUTORIAL
Part 1: AutoCAD Basics The Subtract tool The Subtract tool is used to subtract one or more solid objects from another object. Create two concentric circles of 240 and 100 mm diameter. first destination point:” appears in the command line. Press and hold the SHIFT key. Right-click and select the Quadrant option. Select the quadrant point of the outer circle on the top face of the hollow cylinder. Use the Presspull tool and extrude up to 250 mm distance. Set the view orientation to Right and create a cylinder of 100 mm diameter and 250 mm length. Change the view orientation to SE Isometric. Expand the Modify panel and click the Press ENTER; the horizontal cylinder will be aligned with hollow cylinder. Align button. Click Solid > Boolean > Subtract on the Select the horizontal cylinder and press ribbon; the message, “Select solids, surfaces, ENTER; the message, “Specify first source and regions to subtract from” appears above point:” appears in the command line. the command line. Press and hold the SHIFT key. Right-click Select the hollow cylinder and press ENTER; and select the Center option. the message, “Select solids, surfaces, and Select the center point of the front face of the regions to subtract” appears above the horizontal cylinder; the message, “Specify command line. 257
Part 1: AutoCAD Basics Select the horizontal cylinder and press ENTER; it will be subtracted from the hollow cylinder as shown below. The Intersect tool The Intersect tool is used to create a composite solid by finding common volume shared by the selected objects. Use the Presspull tool and extrude the view up to 200 mm height as shown below. Start a new file. Set the view orientation to Front and create the sketch as shown below. Use the Presspull tool and extrude the sketch up to 150 mm distance. Change the View style to Wireframe. Deactivate the 3D Object Snap option on the status bar. Type DS in the command line and press ENTER; the Drafting Settings dialog appears. Click the Object Snap tab and Clear All the Object Snap modes. Now, select the Quadrant and Midpoint options and click OK. Set the view orientation to Top and create the sketch as shown below. 258
Autodesk AutoCAD 2018 and Inventor
For Technical Support, contact us a
Chapter 3: Drawing Aids ...........
Exercise 1 ........................
Using the Fillet Edge tool ........
Starting a New Assembly File ......
TUTORIAL 7 ........................
INTRODUCTION AutoCAD is the industr
Part 1: AutoCAD Basics
Part 1: AutoCAD Basics Starting Aut
Part 1: AutoCAD Basics Tip: If the
Part 1: AutoCAD Basics Graphics Win
Part 1: AutoCAD Basics Infer Constr
Part 1: AutoCAD Basics Dynamic Inpu
Part 1: AutoCAD Basics Annotation S
Part 1: AutoCAD Basics balloon noti
Part 1: AutoCAD Basics Changing the
Part 1: AutoCAD Basics Shortcut Men
Part 1: AutoCAD Basics However, if
Part 1: AutoCAD Basics The Select T
Part 1: AutoCAD Basics Command List
Part 1: AutoCAD Basics DIMSTYLE D U
Part 1: AutoCAD Basics DIST DI Used
Part 1: AutoCAD Basics INSERT I Use
Part 1: AutoCAD Basics MSPACE MS Us
Part 1: AutoCAD Basics QUICKCALC QC
Part 1: AutoCAD Basics SPELL SP Use
Part 1: AutoCAD Basics XLINE XL Use
Part 1: AutoCAD Basics CONE Used to
Part 1: AutoCAD Basics MATERIALASSI
Part 1: AutoCAD Basics SPACETRANS U
Part 1: AutoCAD Basics 46
Part 1: AutoCAD Basics below. Turn
Part 1: AutoCAD Basics Save the fi
Part 1: AutoCAD Basics Example 2(Ce
Part 1: AutoCAD Basics Select the
Part 1: AutoCAD Basics Pick a poin
Part 1: AutoCAD Basics Specify th
Part 1: AutoCAD Basics methods are
Part 1: AutoCAD Basics Activate th
Part 1: AutoCAD Basics 64 Drawing B
Part 1: AutoCAD Basics On the Stat
Part 1: AutoCAD Basics easily turn-
Part 1: AutoCAD Basics click the do
Part 1: AutoCAD Basics From: Locate
Part 1: AutoCAD Basics Using Object
Part 1: AutoCAD Basics Click Zoo
Part 1: AutoCAD Basics Using Zoom-S
Part 1: AutoCAD Basics 80
Part 1: AutoCAD Basics The Copy too
Part 1: AutoCAD Basics command line
Part 1: AutoCAD Basics Define secon
Part 1: AutoCAD Basics The Stretch
Part 1: AutoCAD Basics Rotate Items
Part 1: AutoCAD Basics The Path Arr
Part 1: AutoCAD Basics The followin
Part 1: AutoCAD Basics Convert to A
Part 1: AutoCAD Basics Refine Verti
Part 1: AutoCAD Basics Type 80 in
Part 1: AutoCAD Basics Click OK; t
Part 1: AutoCAD Basics Type 5 and
Part 1: AutoCAD Basics 106
Part 1: AutoCAD Basics 108
Part 1: AutoCAD Basics 110
Part 1: AutoCAD Basics 112
Part 1: AutoCAD Basics created by u
Part 1: AutoCAD Basics Use the Off
Part 1: AutoCAD Basics Click the C
Part 1: AutoCAD Basics Move the p
Part 1: AutoCAD Basics Select t
Part 1: AutoCAD Basics Click the
Part 1: AutoCAD Basics Exercise 4 C
Part 1: AutoCAD Basics Crea
Part 1: AutoCAD Basics Click Annot
Part 1: AutoCAD Basics Diameter DIA
Part 1: AutoCAD Basics Click Anno
Part 1: AutoCAD Basics Break DIMBRE
Part 1: AutoCAD Basics Click Zoom
Part 1: AutoCAD Basics Select the
Part 1: AutoCAD Basics On the Home
Part 1: AutoCAD Basics Click OK
Part 1: AutoCAD Basics Position Coc
Part 1: AutoCAD Basics Click Home
Part 1: AutoCAD Basics Press ENTER
Part 1: AutoCAD Basics Right-click
Part 1: AutoCAD Basics Editing Dime
Part 1: AutoCAD Basics In the Prop
Part 1: AutoCAD Basics Method: Limi
Part 1: AutoCAD Basics Constraint F
Part 1: AutoCAD Basics Select a po
Part 1: AutoCAD Basics Click Par
Part 1: AutoCAD Basics Click the A
Part 1: AutoCAD Basics Also, you wi
Part 1: AutoCAD Basics Click the P
Part 1: AutoCAD Basics Exercise 2 I
Part 1: AutoCAD Basics Example 2: I
Part 1: AutoCAD Basics Click the P
Part 1: AutoCAD Basics You can also
Part 1: AutoCAD Basics Example: Cr
Part 1: AutoCAD Basics Pick a poin
Part 1: AutoCAD Basics 184
Part 1: AutoCAD Basics Enter
Part 1: AutoCAD Basics Set the Ann
Part 1: AutoCAD Basics following ex
Part 1: AutoCAD Basics In the Ins
Part 1: AutoCAD Basics Using Tool P
Part 1: AutoCAD Basics Enter 4 as
Part 1: AutoCAD Basics Expand the
Part 1: AutoCAD Basics option can b
Part 1: AutoCAD Basics Example 1:
Part 1: AutoCAD Basics Select the
Part 1: AutoCAD Basics Creating Gri
Part 1: AutoCAD Basics Insert the
Part 1: AutoCAD Basics Save and cl
Part 2: Inventor Basics
Part 2: Autodesk Inventor Basics In
Part 2: Autodesk Inventor Basics Th
Part 2: Autodesk Inventor Basics Qu
Part 2: Autodesk Inventor Basics Di
Part 2: Autodesk Inventor Basics To
Part 2: Autodesk Inventor Basics 32
Part 2: Autodesk Inventor Basics 9.
Part 2: Autodesk Inventor Basics No
Part 2: Autodesk Inventor Basics Te
Part 2: Autodesk Inventor Basics Ad
Part 2: Autodesk Inventor Basics St
Part 2: Autodesk Inventor Basics Th
Part 2: Autodesk Inventor Basics A
Part 2: Autodesk Inventor Basics 2.
Part 2: Autodesk Inventor Basics 6.
Part 2: Autodesk Inventor Basics Th
Part 2: Autodesk Inventor Basics An
Part 2: Autodesk Inventor Basics 3.
Part 2: Autodesk Inventor Basics 13
Part 2: Autodesk Inventor Basics 2.
Part 2: Autodesk Inventor Basics Pl
Part 2: Autodesk Inventor Basics 9.
Part 2: Autodesk Inventor Basics 26
Part 2: Autodesk Inventor Basics 36
Part 2: Autodesk Inventor Basics Ed
Part 2: Autodesk Inventor Basics 4.
Part 2: Autodesk Inventor Basics Cr
Part 2: Autodesk Inventor Basics Ad
Part 2: Autodesk Inventor Basics 12
Part 2: Autodesk Inventor Basics 3.
Part 2: Autodesk Inventor Basics 4.
Part 2: Autodesk Inventor Basics 7.
Part 2: Autodesk Inventor Basics 16
Part 2: Autodesk Inventor Basics 30
Part 2: Autodesk Inventor Basics 4.
Part 2: Autodesk Inventor Basics 6.
Part 2: Autodesk Inventor Basics 5.
Part 2: Autodesk Inventor Basics 2.
Part 2: Autodesk Inventor Basics 19
Part 2: Autodesk Inventor Basics 2.
Part 2: Autodesk Inventor Basics 34
Part 2: Autodesk Inventor Basics 3.
Part 2: Autodesk Inventor Basics 8.
Part 2: Autodesk Inventor Basics 2.
Part 2: Autodesk Inventor Basics 29
Part 2: Autodesk Inventor Basics 2D
Part 2: Autodesk Inventor Basics 21
Part 2: Autodesk Inventor Basics 35
Part 2: Autodesk Inventor Basics Cr
Part 2: Autodesk Inventor Basics 14
Part 2: Autodesk Inventor Basics Le
Part 2: Autodesk Inventor Basics Ad
Part 2: Autodesk Inventor Basics va
Part 2: Autodesk Inventor Basics Cr
Part 2: Autodesk Inventor Basics 6.
Part 2: Autodesk Inventor Basics 6.
Part 2: Autodesk Inventor Basics 4.
Part 2: Autodesk Inventor Basics 2.
Part 2: Autodesk Inventor Basics 6.
Part 2: Autodesk Inventor Basics 8.
Part 2: Autodesk Inventor Basics Ch
Part 2: Autodesk Inventor Basics 3.
Part 2: Autodesk Inventor Basics Cr
Part 2: Autodesk Inventor Basics
Part 2: Autodesk Inventor Basics 8.
Part 2: Autodesk Inventor Basics 14
Part 2: Autodesk Inventor Basics Cr
Part 2: Autodesk Inventor Basics Yo
Part 2: Autodesk Inventor Basics 12
Part 2: Autodesk Inventor Basics Ch
Part 2: Autodesk Inventor Basics 38
Part 2: Autodesk Inventor Basics 10
Part 2: Autodesk Inventor Basics 8.
Part 2: Autodesk Inventor Basics 6.
Part 2: Autodesk Inventor Basics 4.
Part 2: Autodesk Inventor Basics Th
Part 2: Autodesk Inventor Basics 7.
Part 2: Autodesk Inventor Basics 3.
Part 2: Autodesk Inventor Basics Dr
Part 2: Autodesk Inventor Basics On
Part 2: Autodesk Inventor Basics 1.
Part 2: Autodesk Inventor Basics 2.
Part 2: Autodesk Inventor Basics 11
Part 2: Autodesk Inventor Basics 32
Part 2: Autodesk Inventor Basics 6.
Part 2: Autodesk Inventor Basics 48
Part 2: Autodesk Inventor Basics Pr
Part 2: Autodesk Inventor Basics 20
Part 2: Autodesk Inventor Basics 22