Views
2 months ago

HAIMA 7 Service Manual(MT)-U Heater and air conditioning system

Control

Control system Bolt removal instruction 1. as shown in the figure, the pressure plate should be fixed in place when removing or installing the bolt. BOLT A/C COMPRESSOR Connector of component (view from terminal) Electromagnetic clutch adjustment 1. if shim is to be used for adjustment, those with following thickness should be selected: 0.1 mm {0.004 in} 0.3 mm {0.012 in} 0.5 mm {0.020 in} Standard clearance 0.3-0.7 mm {0.012-0.028 in} 3. examine operation of the electromagnetic clutch. If it is not as specified, replace the rotor winding. Cooling system pressure switch inspection 1. install refrigerant charging device. 2. disconnect the refrigerant pressure switch connector. 3. inspect the reading of high-pressure side on manifold pressure gage and the conduction between all terminals. If the result is nonconforming with technological requirements, replace the fluid reservoir assembly. Electromagnetic clutch inspection 1. disconnect the electromagnetic clutch connector. 2. connect terminal a of electromagnetic clutch to battery positive voltage, and a/c compressor case with ground. Operating characteristic of pressure switch (mpa): Hp:off 3.14±0.2 on 2.55±0.2 diff 0.59±0.2 Lp:off 0.196±0.2 on 0.225±0.2 diff ≥0.02 A/c relay removal/installation 1. disconnect negative battery cable. 2. remove main fuse block cover. 3. remove in order as shown in the table. U-12

Control system 4. install in reverse order as of removal. 1 Connector 2 Front blower relay 1 A/c relay A/c relay inspection 1. remove a/c relay. 2. inspect continuity between the a/c relay terminals with an ohmmeter. If it is not as specified, replace a/c relay. Step Terminal Continuity Blower relay inspection 1. remove the bracket. 2. inspect continuity between the blower relay terminals with an ohmmeter. If it is not as specified, replace the blower relay. Step Terminal Continuity Connector of component (view from terminal) Blower relay removal/ installation 1. disconnect the negative battery cable. 2. remove passenger side panel. Connector of component (view from terminal) 3. install in reverse order as of removal. U-13

Chameleon Warm Air Heater - 1st Systems Engineering
Multi Air Conditioning System for Buildings
High Performance Air-Conditioning - ACS Shop & Service
Precision Split Air Conditioning Systems - Cool Point
Split Systems Catalog - Heating & Air Conditioning
Samsung air Conditioning And Heat Pump Systems
R22 replacement - B&H Services Air Conditioning & Ventilation
Air Conditioning Repair & Service Raleigh, Apex, Garner NC
System Cubicles and Cubicle Air-Conditioning Catalog LV 50 2006
ARB AIR LOCKER SERVICE & PARTS MANUAL
Air heater - ELMESS -Thermosystemtechnik GmbH
GMVC95 - Waunakee Air Conditioning
RefRigeRation and aiR Conditioning - Teesing
Air conditioning Sydney
split unit air conditioner installation manual for service personnel only
AIR-SHIELDS PM 78 Infant Incubator Service Manual
DE HORN Pneumatic Services - HPC Compressed Air Systems
Ducted Air-conditioning gets personal. - Advantage Air
VAHNCW Air Handling - Heronhill Air Conditioning Ltd
Direct Expansion Air Conditioning Chilled Water Air Conditioning ...
Portable Air Conditioning - Alert Electrical
Process Of Heating And Air Conditioning Repair
Air conditioning TISK2.indd - Systemair
Hire 24*7 Emergency Medical ICU Air Ambulance Services in Raipur and Bhopal
Installation & Operation Manual for WarmlyYours ... - Heater Home
Airboss over door heater - 1st Systems Engineering
Solar Water Heating Kits and Heaters Systems
Superior, ultra-quiet power vent water heaters - gta-aire: heating ...