Views
6 months ago

CSS Catalogue 2018/2019 (English)

Assistive technologies for people with disabilities. Full catalogue.

AssistX Call Secure call

AssistX Call Secure call Triggering according to DIN VDE 0834 AssistX Call is equipped with 2 AssistX ports. These can be connected to any 2 single sensors or push-buttons or AssistX port compatible sensors. AssistX Call is delivered to fit the corresponding call system. The power supply, if supported, is provided by the connected call system. If this is not possible, the power supply is provided by an external power supply, protected by a backup battery with several hours of runtime. AssistX Call is a sensor adapter for luminous call systems and enables call triggering using special sensors (call triggers) which cannot be connected directly to the call system. For example, with AssistX Call the proximity sensor AssistX ProX, acoustic sensor AS one, sip-puff encoder Pneumax, infrared receiver AssistX IR one, or various push-buttons, including large-sized push-buttons, can be used to call for help. AssistX Call is powered by the call system or an external power supply. In both cases, the device works even in the event of a power failure in the network. When powered by an external power supply, the built-in lithiumpolymer battery ensures full functionality for a few hours in case of power failure. The device is individually configured for different call systems and delivered with a connection cable pre-configured to the call system. Inputs for call triggering The sensors are connected to the two 3.5 mm input jack plugs. AssistX Call can add and distinguish between different sensors. Safety The AssistX Call monitors safety-relevant parameters. If a proper function is no longer guaranteed, the device triggers a call. Monitored are: •Power supply to the control unit •Sensor error (cable break, ejection) •Function monitoring of the active transmitter •Self-monitoring of the electronics •Defective sensor cable A defective sensor cable A defective sensor / switch cable or an inadvertently unplugged sensor / switch can present a danger to the caller or third persons. If a sensor error is detected, a call is triggered. The error can be displayed visually and acoustically. Pneumax or the PikoButton NC). For simple switches with a normally open contact, it is not possible to detect a defective cable for technical reasons. In order to achieve the highest possible degree of safety in these types of switches as well, simple switches with normally open contact must be operated at least once every 24 hours. As a rule, this is guaranteed in everyday nursing care. If the 24 hours are exceeded without the sensor being activated, a signal light on the AssistX Call flashes and signals that the sensor is no longer considered safe and must be activated. If activation is detected, the LED goes out again. The call is triggered in parallel. However, a sensor / switch test can also be manually requested at any time by the nursing staff (morning routine). Technical data: •Power supply: Power supply via call system 6.5 - 36V DC Ext. •Power supply, max. 500mA with bridging of power failure by LiPo battery min. 24 hours •Switch/Sensor sleeve: 2x jack plug 3,5 mm, AssistX port •Dimensions: 74 x 74 x 26 mm #20445 AssistX Call - Call system interface incl. individual connection to the luminous call system 16 | www.csslabs.de A defective cable can only be detected with sensors with a normally closed contact. (For example, with the proximity sensor AssistX ProX, the acoustic sensor AssistX AS one, Hy-

AssistX ® Mobil AssistX® Mobil Secure wireless call triggering according to DIN VDE 0834. AssistX Mobil Wireless home and nurse call system Assist X Mobil is a wireless home and nurse call system with connection for any triggering sensors, switches or push-buttons with 3.5 mm jack plug. The basic system consists of transmitter, receiver and a USB charger. The receiver can be easily carried on the belt using a clip. The AssistX Mobil radio paging system is the ideal solution when nursing care with mobility and safety at the same time is required . AssistX Mobil is connected in less than 5 minutes and easy to use. Depending on the level of disability, special sensors for triggering the distress call can be plugged into the transmitter's connection socket. This allows even people with the most severe disabilities to make a call with an individual sensor. Several transmitters, as well as several receivers can be used together. Thus, the system is also particularly suitable for use in small residential groups. The name of the caller or the room is displayed in plain text on the display of the receiver (s). Functional principle: By pushing the button or operating a plugged in push-button / switch, a radio paging is triggered by the transmitter. This is signaled visually and acoustically to the caller. The radio paging is picked up by the receiver and signaled visually, acoustically and by vibration. The receiver then sends back an acknowledgment signal to confirm proper reception. If this acknowledgment signal is missing, the call is repeated automatically. The caller recognizes the acknowledgment by the light of a red calming lamp. At the receiver, the call must be acknowledged by pressing the "OK" key. This stops the acoustic and optical signaling. After this, the triggered call must be acknowledged manually with the caller. If this does not occur within a certain time, the call process is automatically repeated from the beginning. Perfect individual call triggering: AssistX Mobil is equipped with an AssistX port (see page 15) for call triggering. This one can be connected with any simple switches, push-buttons or AssistX Port compatible sensors. As a result, in addition to standard simple switches, the AssistX ProX one proximity sensor or the AssistX AS one acoustic sensor can be inserted directly into the transmitter and used to trigger the call. No additional power supply or cable is required. Particularly safe: The AssistX Mobil network communicates in the protected "Social Alarm" frequency band (869 MHz). This makes the system particularly protected against interfering radio signals from other devices. Both transmitters and receivers have installed a powerful Lipo battery with a running time of at least 24 hours as power supply. AssistX Mobil also features a range detection. If a transmitter is out of range, this is indicated in the receiver. A low battery charge status of the transmitter is also displayed in the receiver and alarmed before reaching a critical level. All calls are recorded in the receiver with their origin, date and time so that they can be evaluated later, if necessary. Technical data: •Secure wireless call system according to DIN VDE 0834. •Transmitter is equipped with an AssistX port •Battery and function monitoring of the transmitter •Range monitoring •Acknowledgement by soothing lamp function •Adjustable volume •Optical and acoustic signaling •Vibration signaling •Social Alarm (869 MHz) •Group: Several transmitters can be interconnected to several receivers •An individual name can be assigned to each transmitter. •Large color display in the receiver •Battery life: Depending on the sensor inserted up to several days. •Receiver configurable by display menu or PC •Dimensions: approx. 65 x 119 x 26.5 mm #20450 AssistX Mobil set consisting of transmitter, receiver and charger #20451 AssistX Mobil transmitter TX4 #20452 AssistX Mobil receiver RX4 For European market only - Please ask for US version. www.csslabs.de | 17

CSS / INCAP Catalogue 2016/2017 (English)