5 years ago

0712-0299ZX60USB-3 - Flannery Plant Hire

0712-0299ZX60USB-3 - Flannery Plant Hire


MAINTENANCE Check and Replace Seat Belt Check --- daily Replace --- every 3 years Prior to operating the machine, thoroughly examine belt (1), buckle (2) and attaching hardware (3). If any item is damaged or materially worn, replace the damaged or worn item(s) before operating the machine. Replace seat belt (1) every three years regardless of its apparent condition. NOTE: The seat belt is optional on the machine equipped with the 2-post canopy. 7-64 2 1 3 M1M0-07-023

Check Air Conditioner --- daily MAINTENANCE CAUTION: If refrigerant splashes into eyes or spills onto skin, blindness or cold contact burn may result. Never loosen the refrigerant circuit parts. Check for refrigerant leaking from the pipe joints If an oil seepage mark is found at the pipe joints illustrated to the right, the refrigerant is possibly leaking. Check the refrigerant level After operating the air conditioner in the cooling mode for 2 to 3 minutes with the engine running at 1500 min -1 (rpm), check the refrigerant level through sight glass (inspection window) (2) on receiver dryer (1). Kind: HFC134a Mass: 0.85±0.05kg Check the condenser If the condenser surface is contaminated with foreign matter such as dust or dead insects, cooling performance may be reduced. Keep the condenser clean. (Refer to the descriptions for Clean Radiator in INSPECTION AND MAINTENANCE section.) Check the compressor After operating the air conditioner for 5 to 10 minutes, touch both high and low pressure pipe lines with your hands. Normally, the high pressure side should be hot and the low pressure side should be cool. Check each bolt for looseness Check that the compressor mounting bolts and all other tightening bolts are securely tightened. Check the compressor belts and fan belts Check all belts for looseness and/or wear. If any faulty is found, consult your authorized dealer for receiving detailed inspection. Adjust compressor belt tension Visually check the belt for wear. Replace if necessary. Check compressor belt tension by depressing the midpoint between compressor pulley and crank pulley with the thumb. Deflection must be 8 to 10 mm (0.32 to 0.39 in) with a depressing force of approximately 98 N (10 kgf, 22 lbf). If tension is not within specifications, loosen nut (2). Move the tension pulley (1) by bolt (3) until tension is correct. Tighten nut (2) correctly. Tightening torque: 41 to 50 N·m (4.1 to 5.0 kgf·m, 30 to 37 lbf·ft) NOTE: When a new belt is installed, be sure to re-adjust the tension after operating the engine for 3 to 5 minutes at slow idle speed to be sure that the new belt is seated correctly. 7-65 Fan Pulley Depress [Approx. 98N (10 kgf, 22 lbf)] Tension Sag: Pulley 8 to 10 mm (0.32 to 0.39 in) Compressor Pulley 3 1 2 No Refrigerant Empty Sufficient Quantity Insufficient Quantity Crank Pulley 2 1 M1M7-07-057 Almost clear. A few bubbles may appear when the engine speed is raised or lowered. Compressor Pulley M107-01-050 Alternator Pulley M1M7-07-013 M1M0-07-024

Neuson Zero-Tail Swing Excavator 50Z3/6003 - Chase Plant Hire
Get inspired by - Green Design Plant Hire
Ridgway Rentals Plant Machinery Guide May 17
3. Fusarium mycotoxins in cereals - Plant Research International ...
4878 JS200W Spec (Iss2) (UK) - Flannery Plant Hire
Quick Coupler Safety Quick Coupler Safety - Flannery Plant Hire
s130 skid-steer loader specifications - Ringby Plant Hire Ltd
MINIMIX 150 - Rapid Plant and Tool Hire
New Copy of Stock List Hire Rates - Baileys Plant Hire Ltd
Hiring cell gatekeepers - ABC transporters in plant ... - BioTechnologia
15. LOADERS - CPHA - Contractors Plant Hire Association
Pacific Coast Canola Begins Hiring for New Plant - Legumex Walker ...
JCB TRACKED EXCAVATOR | JS130 L T.A.B. - Exuma Plant Hire
Hilti - TE15-C - Light Duty Electric Breaker - Exsel Plant & Tool Hire Ltd
CES 3 2011 Hire of Plant SCHEDULES - Drakenstein municipality
Construction Plant World - 28th June 2018
Atlas Copco Portable air compressors Series 7, - Plant Hire UK Limited