5 years ago

0712-0299ZX60USB-3 - Flannery Plant Hire

0712-0299ZX60USB-3 - Flannery Plant Hire


MAINTENANCE IMPORTANT: The operation torque of adjuster screw (4) shall be less than 25 N⋅m (2.5 kgf⋅m, 18 lbf⋅ft). In case the operating torque requires more than 25 N⋅m (2.5 kgf⋅m, 18 lbf⋅ft), bolts (3) may not be completely removed yet. Recheck whether all bolts (3) are completely removed. If tilt up the cab floor without removing bolts (3) by mistake, replace adjusting screw (4) so that adjusting screw (4) may be deformed, or cracked and broken. 10. Turn adjuster screw (4) to tilt cab assembly toward the front attachment. Wrench size: 17 mm 11. Turn adjuster screw (4) clockwise until disc plate (5) on the side of the floor tilt mechanism is moved to the illustrated position. IMPORTANT: Do not tilt the cab using other than the floor tilt mechanism (such as a crane). Failure to do so may cause damage to the floor tilt mechanism and/or floor. 7-76 5 4 5 mm M1M0-07-034 4 M1M0-07-036

TILTING FLOOR DOWN WARNING: Do not quickly lower the floor. If the adjust screw (4) is quickly turned to lower the floor, the floor may severely vibrate, potentially creating hazardous conditions. MAINTENANCE 1. Before tilting the cab floor down, check if any tools or workshop towels are not left behind on the base machine or in the operator’s cab and the safety lock bar has been stowed in position. 2. Slowly turn adjuster screw (4) counterclockwise. Wrench size: 17 mm 3. Continue to turn adjuster screw (4) counterclockwise until the edge of bracket (13) comes in contact with bearing bracket (7). WARNING: If adjuster screw (4) is continuously turned after the floor is completely lowered, when the adjuster screw is extended by approx. 15 mm (0.6 in), washer (10) will come in contact with the end face of pin (11) so that adjuster screw (4) will not turn further. Take care that if adjuster screw (4) is forcibly turned further, deformation of washer (10) or missing of bolt (12) may result. 4. When the floor is completely lowered, adjuster screw (4) will be extended. Adjust the clearance between flange (8) of adjuster screw (4) and contact face (9) to 2 to 5 mm (0.1 to 0.2 in). 7-77 12 8 9 7 13 10 2~5 mm 11 4 M1M7-07-068 W1M9-01-05-002 9 2~5 mm 8 4 M1M7-07-075

Neuson Zero-Tail Swing Excavator 50Z3/6003 - Chase Plant Hire
Get inspired by - Green Design Plant Hire
Ridgway Rentals Plant Machinery Guide May 17
3. Fusarium mycotoxins in cereals - Plant Research International ...
4878 JS200W Spec (Iss2) (UK) - Flannery Plant Hire
Quick Coupler Safety Quick Coupler Safety - Flannery Plant Hire
s130 skid-steer loader specifications - Ringby Plant Hire Ltd
MINIMIX 150 - Rapid Plant and Tool Hire
New Copy of Stock List Hire Rates - Baileys Plant Hire Ltd
Hiring cell gatekeepers - ABC transporters in plant ... - BioTechnologia
15. LOADERS - CPHA - Contractors Plant Hire Association
Pacific Coast Canola Begins Hiring for New Plant - Legumex Walker ...
JCB TRACKED EXCAVATOR | JS130 L T.A.B. - Exuma Plant Hire
CES 3 2011 Hire of Plant SCHEDULES - Drakenstein municipality
Hilti - TE15-C - Light Duty Electric Breaker - Exsel Plant & Tool Hire Ltd
Atlas Copco Portable air compressors Series 7, - Plant Hire UK Limited
“Association of German Machine and Plant Engineering (VDMA ...