Views
5 years ago

RIMA SYSTEM

RIMA SYSTEM

RIMA

RIMA SYSTEM � To change the response speed: � Press and hold the [MODE] button for about 3 seconds to enter the setup mode � " SPd 3 " appears, with the red value flashing � Used the [UP] or [DOWN] arrows buttons to change the response time: 1.5, 3, 10, 20, 50 (ms) � Press and hold the [MODE] button for another 3 seconds to exit the setup mode. � Resetting to factory preset settings (custom reset) � Return all of the settings to the RIMA saved settings: � While pressing the [MODE] button, press the [SET] button five times � Press the [DOWN] arrow button to display “ rSt no ". � When " rSt no " is displayed, pressing the [MODE] button returns to the main screen without initializing � Press the [LEFT] or [RIGHT] arrow button to select " rSt CST ", and then press the [MODE] button to load the settings � RIMA settings RIMA settings Note SPd 3 ms out noo Output 1: N.O. (Default value) Output 2: N.O. Pro Fnc A-1 Edge hold mode ClP oFF (Default value) t-1 off One-Shot, to get there press arrow up 3 times: off [UP] ofd [UP] ond [UP] Sht Sht 20 Output pulse duration (ms) t-2 oFF (Default value) HYS USr User HYS 1 Default was 2 in SFt Use a “external shift input” In A-1 mode the sensor resets after every external input. NOTE: the black (output 1) and pink (input) wire are jumped. SFt 0 (Default value) dSt nor (Default value) Eco oFF (Default value) end To exit at any point from the setup, press and hold the [MODE] button for 5 seconds. � Initial Reset (Initialization) � Return all of the settings to the factory settings: � While pressing the [MODE] button, press the [SET] button five times � Press the [DOWN] arrow button to display “ rSt no ". � When " rSt no " is displayed, pressing the [MODE] button returns to the main screen without initializing � Press the [UP] or [DOWN] arrow button to select " rSt ini ", and then press the [MODE] button to initialize. LaserCounter.Operation_v4.doc 2

RIMA SYSTEM � Custom Settings LaserCounter.Operation_v4.doc RIMA Settings Note SPd 3 out noo Pro Fnc A-1 ClP oFF t-1 off ofd --- ond --- Sht --- Sht 20 ms Output 1: N.O. Output 2: N.O. (Default value) Edge hold mode (Default value) Press [Arrow UP] Press [Arrow UP] Press [Arrow UP] One-Shot: Press [MODE] Output pulse duration (ms) 3

Racial Purity and Dangerous Bodies: Moral Pollution, Black Lives, and the Struggle for Justice (Rima L. Vesely-Flad)
Comparison of Change Management Systems
PCE-IMS 1 User Manual IPMonitoring systems IPSwitchable ...
hill & smith holdings plc - Techspan Systems
Toyota Production System (TPS) - free lean manufacturing
Height measurement system - Rampf Formen GmbH
download - Building Management Systems, Frank Lenders
Create your Experience – with EST - EST Engineering Systems ...
AT&T UNIX™PC Unix System V Users Manual - tenox
2012 Instrument Systems Manual - MasterCraft
Eingebettete Systeme / Embedded Systems
Suite 8000 Series - Hill Residential Systems
User Manual - Car Guard Systems GmbH
2-way car alarm system with remote engine start - Net Trading
Fuel Management Systems Submersible Pumping ... - UPP Systems
ABLOY® FIRE DOOR CLOSING SYSTEMS
Cable entry and cable holding systems Solutions for ... - Eegholm
Cable entry and cable holding systems Solutions for ... - Murrplastik
An Overview of the Electronic Systems for Students of Justus ... - Setup
MicroE Systems
Blower Anti Heeling System