midi cc reference tables - Line 6

More documents

Recommendations

Info

MIDI Connectivity 1•2 Overview Your DT Series amplifier will respond to specific MIDI CC messages to configure preamp, power amp, switch amp channels, control tone knobs, etc. (See the MIDI CC tables in the following chapter for the list of specific parameters & commands.) You can use any manufacturer’s external MIDI controller device that is capable of configuring MIDI CC commands and values, and that includes a standard 5-pin MIDI OUT jack. Connect a standard MIDI cable from the controller device’s MIDI OUT to the 5-pin MIDI IN port on the back of your DT Series amp. There is no other configuration of the DT amp necessary for MIDI control - it will respond to valid MIDI CC messages on MIDI Channel 1. The 5-pin MIDI In & OUT ports on the back of the DT Series amplifiers Got a POD HD500 or POD HD Pro? These devices are capable of functioning as MIDI controllers, where you can configure the specific MIDI CC messages to be sent from its footswitches & pedals. See the POD HD Advanced Guide PDFs at http://line6.com/support/manuals. Or, if you have an Apple® iPhone®, iPod touch® or iPad®*... Check out the Line 6 MIDI Mobilizer II, the mobile app & MIDI interface that lets you take control of MIDI devices anywhere! See http://line6.com/midimobilizer/mmii/ for details. DT Amplifier Factory Reset As mentioned in the above sections, when customizing any settings via MIDI, your changes remain “saved” internally on the DT amplifier. This includes changes made to the preamp and power amp per Voicing switch value, Reverb and more. To return all settings back their factory default state, you’ll need to perform a “Reset” of the DT amp. To perform the Reset, start with the DT amplifier powered “Off,” then simultaneously hold the Voicing toggle switch DOWN and the Pentode/Triode toggle switch UP while powering the amp “On.” Continue to hold these toggle switches in this position until you see the Voicing “I” indicator light up (this takes about 15 seconds). The DT factory default settings are then fully restored and your DT amp is ready to play. Hold the Voicing switch Down Hold the Pentode/Triode switch Up Turn the Power On with other switches held * Apple®, iPod touch®, iPhone® and iPad® are trademarks of Apple Inc., registered in the U.S. and other countries. Apple® is not responsible for the operation of this device or its compliance with safety and regulatory standards.
MiDi CC referenCe Tables 2•1 MIDI CC Reference Tables This chapter includes tables showing the MIDI CC messages required to control specific functions on your Line 6 DT Series amplifier. Configure your MIDI controller device to transmit the MIDI CC number and specific values as listed in these tables. The MIDI CCs listed are supported by both DT50 and DT25 amplifiers, except where noted. Please consult the manufacturer’s documentation included with your external MIDI control device for its instruction on how to configure it to send the necessary MIDI CC messages. Global Parameters Table The parameters in this table are “Global,” meaning they are not specific to the DT amp’s Channel A or B, or to any Voicing switch setting. Once changed, the state for each of these settings persist on the amp until changed again either via MIDI, or via the DT amp panel options. Channel A/B Select Selects Channel A or B Channel A/B Toggle Global Parameters Parameter & Description MIDI CC Value Sending any Value 0 - 127 toggles to the opposite Channel A or B XLR Direct Out Mic Emulation Selects the speaker cabinet’s Mic type, applied to the audio signal heard from the DT amp’s XLR Direct Output 19 66 0 - 127 82 0 - 63 = Channel A 64 - 127 = Channel B 0 = None 1 = 57 Dynamic 2 = 57 Dynamic, Off Axis 3 = 409 Dynamic 4 = 421 Dynamic 5 = 4038 Ribbon 6 = 121 Ribbon 7 = 67 Condenser 8 = 87 Condenser
Page 1 and 2: DT Series Amplifiers MIDI Implement
Page 3: Overview 1•1 Overview The revolut
Page 7 and 8: Channel A & B Parameters Table 2•
Page 9 and 10: Cab Select Parameter & Description
Page 11: Reverb Mix Parameter & Description

midi cc reference tables - Line 6

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?