VF-FS1 Industrial Inverter - Toshiba

More documents

Recommendations

Info

9 [Example of wiring] Note: Strip and earth the shielded cable, following the example shown in Fig. Shielded cable 9.1.3 About the low-voltage directive Strip the cable and fix it to the metal plate by means of a metal saddle for electrical work or equivalent. I-4 E6581381 The low-voltage directive provides for the safety of machines and systems. All Toshiba inverters are CEmarked in accordance with the standard EN/IEC 61800-5-1 specified by the low-voltage directive, and can therefore be installed in machines or systems and imported without problem to European countries. Applicable standard: EN/IEC 61800-5-1 Adjustable second electrical power drive system
9.1.4 Measures to satisfy the low-voltage directive I-5 E6581381 When incorporating the inverter into a machine or system, it is necessary to take the following measures so that the inverter satisfies the low-voltage directive. (1) Install the inverter in a cabinet and ground the inverter enclosure. When doing maintenance, be extremely careful not to put your fingers into the inverter through a wiring hole and touch a charged part, which may occur depending on the model and capacity of the inverter used. (2) Do not connect two or more wires to the main circuit earth terminal of the inverter. If necessary, install an additional earth terminal on the metal plate on which the inverter is installed and connect another cable to it. Or install the EMC plate (attached as standard) and another cable connect to earth terminal on the EMC plate. Refer to the table 10.1 for earth cable sizes. (3) Install a non-fuse circuit breaker or a fuse on the input side of the inverter. 9.2 Compliance with UL Standard and CSA Standard The VF-FS1 models, that conform to the UL Standard and CSA Standard have the UL/CSA mark on the nameplate. 9.2.1 Compliance with Installation The VF-FS1 inverter must be installed in a panel, and used within the ambient temperature specification. ⇒ See section 1.4.4. 9.2.2 Compliance with Connection Use the UL conformed cables (Rating 75 °C or more) to the main circuit terminals (R/L1, S/L2, T/L3, U/T1, V/T2, W/T3). For instruction in the United States, Integral solid state short circuit protection does not provide branch circuit protection. Branch circuit protection must be provided in accordance with the National Electrical Code and any additional local codes. For instruction in the Canada, Integral solid state short circuit protection does not provide branch circuit protection. Branch circuit protection must be provided in accordance with the Canadian Electrical Code and any additional local codes. Refer to the table of next page about wire sizes. 9
Page 1 and 2:
Industrial Inverter For 3-phase ind
Page 3 and 4:
I General Operation Disassembly pr
Page 5 and 6:
4 E6581381 I Warning See item • E
Page 7 and 8:
I Disposal Mandatory 6 E6581381 Cau
Page 9 and 10:
⎯⎯ Contents ⎯⎯ I Safety pre
Page 11 and 12:
iii E6581381 12. Specifications....
Page 13 and 14:
1 1.2 Contents of the product Expla
Page 15 and 16:
1 Charge lamp Indicates that high v
Page 17 and 18:
1 VFFS1-2004 ∼ 2037PM VFFS1-4004
Page 19 and 20:
1 VFFS1-2220PM -4220, 4300, 4370, 4
Page 21 and 22:
1 22kW or more: Switch 3) Control c
Page 23 and 24:
1 A-12 E6581381 1.3.4 How to open t
Page 25 and 26:
1 Low loads and low inertia loads A
Page 27 and 28:
1 Power factor correction capacitor
Page 29 and 30:
1 (2) Affects of leakage current ac
Page 31 and 32:
1 A-20 E6581381 • Do not install
Page 33 and 34:
1 Calorific values of the inverter
Page 35 and 36:
2. Connection Disassembly prohibite
Page 37 and 38:
2.2.1 Standard connection diagram 1
Page 39 and 40:
2.3 Description of terminals 2.3.1
Page 41 and 42:
Terminal symbol Input/output Functi
Page 43 and 44:
B-9 E6581381 SINK (Negative) logic
Page 45 and 46:
3. Operations Prohibited Mandatory
Page 47 and 48:
3.1.1 How to start and stop Exampl
Page 49 and 50:
(2) Setting the frequency using the
Page 51 and 52:
Ex.2 (1) Wiring MCCB C-7 E6581381 R
Page 53 and 54:
4 4.1 Flow of status monitor mode F
Page 55 and 56:
4 4.2.1 How to set the basic parame
Page 57 and 58:
4 Example of parameter setting D-6
Page 59 and 60:
4 D-8 E6581381 [Parameter setting]
Page 61 and 62:
4 D-10 E6581381 4.2.6 Parameters th
Page 63 and 64:
5. Basic parameters Before you oper
Page 65 and 66:
E-3 E6581381 [Parameter setting] Ti
Page 67 and 68:
Coast stop (=) E-5 E6581381 Setting
Page 69 and 70:
5.3 Selection of operation mode Loc
Page 71 and 72:
E-9 E6581381 Title Function Adjust
Page 73 and 74:
Resolution All FM terminals have a
Page 75 and 76:
5.5 Standard default setting : Def
Page 77 and 78:
5.6 Forward/reverse run selection (
Page 79 and 80:
E-17 E6581381 [Parameter setting] T
Page 81 and 82:
E-19 E6581381 Warning: When setting
Page 83 and 84:
Motor constant must be set E-21 E65
Page 85 and 86:
Relationship between V/F control mo
Page 87 and 88:
E-25 E6581381 [Parameter setting] T
Page 89 and 90:
[Using a VF motor (motor for use wi
Page 91 and 92:
E-29 E6581381 2) Preset-speed frequ
Page 93 and 94:
6. Extended parameters Extended par
Page 95 and 96:
Output frequency [Hz] Designated fr
Page 97 and 98:
Output frequency [Hz] + ― Ov
Page 99 and 100:
F-7 E6581381 • Function Use the a
Page 101 and 102:
3) Sink (Negative) logic / Source (
Page 103 and 104:
F-11 E6581381 (1) A signal is sent
Page 105 and 106:
6.3.6 Analog VIA / VIB detection :
Page 107 and 108:
6.4 Basic parameters 2 6.4.1 Switch
Page 109 and 110:
F-17 E6581381 [Parameter setting] T
Page 111 and 112:
F-19 E6581381 [Parameter setting] T
Page 113 and 114:
RUN command Incrementing (UP) signa
Page 115 and 116:
6.5.4 Fine adjustment of frequency
Page 117 and 118:
6.7 DC braking 6.7.1 DC braking :
Page 119 and 120:
PID command value LL F-27 E6581381
Page 121 and 122:
6.10 Bumpless operation LOC REM Key
Page 123 and 124:
100% 90% 80% 70% 60% Reduction of r
Page 125 and 126:
400V Class for IP20] Output current
Page 127 and 128:
2) Restarting motor during coasting
Page 129 and 130:
Mandatory 6.12.3 Retry function :
Page 131 and 132:
6.12.4 Avoiding overvoltage trippin
Page 133 and 134:
F-41 E6581381 [0: Supply voltage un
Page 135 and 136:
F-43 E6581381 The droop control fu
Page 137 and 138:
2) Types of PID control interfaces
Page 139 and 140:
(D-gain adjustment parameter) F-47
Page 141 and 142:
[Selection 1: Setting vector contro
Page 143 and 144:
F-51 E6581381 : Using this paramete
Page 145 and 146:
6.16 Acceleration/deceleration time
Page 147 and 148: F-55 E6581381 Title Function Adjust
Page 149 and 150: How to set parameters a) Operating
Page 151 and 152: F-59 E6581381 [Display during opera
Page 153 and 154: 6.17.5 Output phase failure detecti
Page 155 and 156: F-63 E6581381 Title Function Adjust
Page 157 and 158: 1) Output terminal function: 12 (OT
Page 159 and 160: 6.17.12 Undervoltage trip : Underv
Page 161 and 162: F-69 E6581381 Output of part repla
Page 163 and 164: 6.18 Forced fire-speed control func
Page 165 and 166: 6.20 Operation panel parameter F-73
Page 167 and 168: F-75 E6581381 6.20.3 Displaying the
Page 169 and 170: An example of setting when is 80 a
Page 171 and 172: Example of setting 2 F-79 E6581381
Page 173 and 174: F-81 E6581381 [Parameter setting] T
Page 175 and 176: The following are available as comm
Page 177 and 178: 6.21.2 Using the RS485 Setting the
Page 179 and 180: 6.22 Parameters for options : Para
Page 181 and 182: 7 (3) Input voltage setting 1 (0 to
Page 183 and 184: 7 Current signal Voltage signal G-4
Page 185 and 186: 7 G-6 E6581381 (3) Operation from a
Page 187 and 188: 8 Note 4 Note 5 Note 5 (Continued)
Page 189 and 190: 8 Note 10 Note 1 Note 2 Note 3 Note
Page 191 and 192: 8 Note 3 (Continued) Error code Fai
Page 193 and 194: 8 Note 6 Note 6 Note 6 Note 6 Note
Page 195 and 196: 9. Measures to satisfy the standard
Page 197: I-3 E6581381 Three-phase 400V class
Page 201 and 202: Voltage class Three-phase 200V clas
Page 203 and 204: 10 J-2 E6581381 Note 4: For IEC, th
Page 205 and 206: 10 Magnetic contactor in the secon
Page 207 and 208: 11. Table of parameters and data 11
Page 209 and 210: Title Communication No. Function Un
Page 211 and 212: • Frequency parameters Title Comm
Page 213 and 214: Title Communicatio n Function Unit
Page 217 and 218: • Output parameters Title Communi
Page 221 and 222: Table of input terminal functions 1
Page 223 and 224: Table of output terminal functions
Page 225 and 226: Table of output terminal functions
Page 227 and 228: 12 Principal control functions L-2
Page 229 and 230: 12 12.2 Outside dimensions and mass
Page 231 and 232: 12 Fig.E Fig.F Fig.G L-6 E6581381
Page 233 and 234: 13. Before making a service call -
Page 235 and 236: M-3 E6581381 Error code (Continued)
Page 237 and 238: M-5 E6581381 Note: When the ON/OFF
Page 239 and 240: 13.4 How to determine the causes of
Page 241 and 242: 14 Check points 1. Something unusu
Page 243 and 244:
14 N-4 E6581381 1) Cooling fan The
Page 245 and 246:
15. Warranty O-1 E6581381 Any part
Page 247:
TOSHIBA TOSHIBA INDUSTRIAL PRODUCTS
show all

VF-FS1 Industrial Inverter - Toshiba

Create successful ePaper yourself

Delete template?

Save as template?