Quick Reference Guide - Savant Dealer Portal
Quick Reference Guide - Savant Dealer Portal
Quick Reference Guide - Savant Dealer Portal
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
The <strong>Savant</strong> Wireless Thermostat (SST-W100) is a Wi-Fi enabled wireless digital thermostat<br />
designed to control Heating, Ventilation and Air Conditioning (HVAC) systems which<br />
communicate wirelessly over Wi-Fi to a <strong>Savant</strong> System. The SST-W100 is designed to integrate<br />
seamlessly into a <strong>Savant</strong> controlled environment.<br />
Box Contents<br />
(1) SST-W100<br />
(1) Installation Kit (xxx)<br />
(1) <strong>Quick</strong> <strong>Reference</strong> <strong>Guide</strong> (this document)<br />
Optional Components<br />
SST-TEMP1 - Remote Temperature Sensor<br />
Specifications<br />
Environmental<br />
Temperature 32° to 104° F (0° to 40° C)<br />
Humidity 10% to 90% Relative Humidity (non-condensing)<br />
Dimensions and Weight<br />
Height 3.96 in/10.06 cm<br />
Width 5.775 in/14.67 cm<br />
Depth .58 in/1.47 cm<br />
Weight 0.5 lb/.23 kg<br />
Power<br />
Power Supply 24V AC (requires both R and C from the HVAC system)<br />
Compliance<br />
Safety and Emissions FCC Part 15 | UL Class 2<br />
RoHS Compliant<br />
Front View of SST-W100<br />
System Status<br />
Room<br />
Temperature<br />
Backlite<br />
Display<br />
Menu<br />
Front View with Callouts<br />
Time<br />
Outside<br />
Temperature<br />
Heating/Cooling<br />
Mode Selection<br />
Relative<br />
Humidity<br />
Fan Mode Selection<br />
Setpoints<br />
Run/Hold<br />
Mode Selection<br />
<strong>Savant</strong> Wireless Thermostat<br />
(SST-W100)<br />
<strong>Quick</strong> <strong>Reference</strong> <strong>Guide</strong><br />
Warmer<br />
Colder<br />
Rear View of SST-W100<br />
Holes for mounting<br />
on wall screws<br />
One of the 16 screw-down<br />
connectors used for wiring<br />
to climate control devices<br />
Wiring<br />
Screw-down connectors on the inside of the back cover of the SST-W100 are used for wiring<br />
connections to various climate control devices. Use the next figure to identify these connectors<br />
described in the next table.<br />
Screw-down Connectors on SST-W100<br />
Left Side Right Side<br />
24RC Cooling 24V 24C 24V AC Common (Required)<br />
G Fan Output 24RH 24V Heating<br />
Y1 Cooling Stage 1 output<br />
(Compressor)<br />
Y2 Cooling Stage 2 output<br />
(Compressor)<br />
W1 Heat Stage 1 output<br />
(standard gas/electric HVAC)<br />
Auxiliary Heating<br />
(heat pump HVAC)<br />
W2/O Heat Stage 2 output<br />
(standard gas/electric HVAC)<br />
Change Over Valve<br />
(heat pump HVAC)<br />
RS2 Remote Sensor 2 RS1 Remote Sensor 1<br />
RS2 Remote Sensor 2 RS1 Remote Sensor 1<br />
RSC Sensor Shield RSC Sensor shield<br />
A1 Auxiliary 1 Relay A2 Auxiliary 2 Relay<br />
009-0793-01<br />
SST-W100-00<br />
NOTE: The <strong>Savant</strong> Wireless Remote Temperature Sensor (SST-TEMP1) <strong>Quick</strong> <strong>Reference</strong><br />
<strong>Guide</strong> is available at: dealers.<strong>Savant</strong>Systems.com<br />
<strong>Savant</strong> Hardware > Energy Management<br />
121912
Standard Gas/Electric HVAC System Wiring<br />
Standard Gas/Electric HVAC System Wiring<br />
Optional 24R Connection for single transformer HVAC Systems<br />
RC and RH are jumpered together on thermostat board.<br />
Cut RC/RH jumper JP1 for separate heating & cooling transformers<br />
Cooling 24V<br />
Fan<br />
24RC<br />
G<br />
24C<br />
24RH<br />
24VAC Com<br />
24V Heating<br />
Cooling stage 1 Y1<br />
W1 Heating stage 1<br />
Cooling stage 2 Y2<br />
W2/O Heating stage 2<br />
Remote Sensor 2 RS2<br />
RS1 Remote Sensor 1<br />
Remote Sensor 2 RS2<br />
RS1 Remote Sensor 1<br />
Sensor shield RSC<br />
RSC Sensor shield<br />
Humidity Relay A1 Relay Com HC A1<br />
A2 H1 A2 Humidity Relay Relay<br />
Shielded cable<br />
Remote Sensor RS2 Remote Sensor RS1<br />
Common Contact<br />
Closure<br />
24VAC Input<br />
Optional Feature<br />
Humidifier/Dehumidifier<br />
Common<br />
24VAC<br />
Thermostat back<br />
Thermostat Setup:<br />
Standard Gas/Electric HVAC Systems<br />
To set the HVAC system type, go to the Main Menu Thermostat Info screen<br />
Default Setup:<br />
and press and hold the Setup button.<br />
� HVAC Type: Gas/Elec<br />
� Fan Type: Gas<br />
1. Type. Set the HVAC System Type: set to Gas/Elec<br />
� 2<br />
2. Fan Type. Set the HVAC Fan Type:<br />
Set to Gas for typical gas furnace (fan is controlled by the furnace)<br />
nd Stage Heat: No<br />
� 2 nd Y2 Compressor Stage 2<br />
Optional Feature<br />
Dehumidifier<br />
NOTE:If there is a separate transformer for the heating and cooling system, clip the jumper<br />
(JP1)located next to the mini-USB connector on the right side of the circuit board.<br />
For installation of the SST-W100 Wireless Thermostat, see the SST-W100 Deployment Stage Cool: <strong>Guide</strong> No<br />
available at: dealers.<strong>Savant</strong>Systems.com<br />
Set to Elec for electric heat (fan call with heat call)<br />
<strong>Savant</strong> Hardware 3. 2nd Stage Heat. > Energy Enable second Management<br />
stage heating outputs<br />
If you have a single stage heating system, leave this set to N<br />
If you have a 2 stage heating system, set to Y to enable.<br />
4. 2nd Stage Cool. Enable second stage cooling outputs<br />
If you have a single stage cooling system, leave this set to N.<br />
If you have a two stage cooling system, set to Y to enable.<br />
Shielded cable<br />
Standard HVAC System<br />
Thermostat Connection<br />
C 24VAC Common<br />
R 24VAC Return<br />
W1 Heat Stage1<br />
W2 Heat Stage 2<br />
G Fan<br />
Y1 Compressor Stage 1<br />
No setup required for this<br />
configuration<br />
DCN: 141-02048-01 Page 19<br />
Copyright © 2012 <strong>Savant</strong> Systems, LLC. SAVANT and RacePoint Blueprint are trademarks of <strong>Savant</strong> Systems, LLC.<br />
All brand names, product names and trademarks are the property of their respective owners.<br />
<strong>Savant</strong> Systems, LLC reserves the right to change product specifications without notice.<br />
*<br />
<strong>Savant</strong> Wireless Thermostat<br />
(SST-W100)<br />
<strong>Quick</strong> <strong>Reference</strong> <strong>Guide</strong><br />
Heat Pump HVAC System Wiring<br />
Heat Pump HVAC System Wiring<br />
Standard Gas/Electric HVAC System Wiring<br />
Thermostat back<br />
For Heat Pump systems, connect the 24R connection<br />
to either the 24RC or 24RH<br />
Optional 24R Connection for single transformer HVAC Systems<br />
RC and RH are jumpered together on thermostat board.<br />
Cut RC/RH jumper JP1 for separate heating & cooling transformers<br />
Cooling 24V<br />
Cooling<br />
Fan<br />
24V<br />
Cooling stage Fan 1<br />
Cooling stage 2 1<br />
Remote Cooling Sensor stage 2<br />
Remote Sensor 2<br />
Remote Sensor Sensor shield 2<br />
24RC<br />
24RC G<br />
Y1 G<br />
Y2 Y1<br />
RS2 Y2<br />
RS2<br />
RSC RS2<br />
24C<br />
24RH 24C<br />
24RH W1<br />
W2/O W1<br />
W2/O RS1<br />
RS1<br />
RS1 RSC<br />
24VAC Com<br />
24VAC<br />
24V Heating<br />
Com<br />
24V Aux Heating Heating<br />
Heating Change stage Over 1 Valve<br />
Heating Remote stage Sensor 2 1<br />
Remote Sensor 1 1<br />
Remote Sensor Sensor shield 1<br />
Humidity Sensor Relay A1 Relay shield Com<br />
Humidity Relay A1 Relay Com<br />
HC RSC A1<br />
HC<br />
RSC A2 H1<br />
H1<br />
Sensor A2 Humidity Relay shield Relay<br />
A2 Humidity Relay Relay<br />
Shielded cable<br />
Shielded cable<br />
Shielded cable<br />
Shielded cable<br />
Remote Sensor RS2<br />
Remote Sensor RS1<br />
Remote Sensor RS2 Remote Sensor RS1<br />
Common Contact<br />
Contact<br />
Closure<br />
Contact Closure Closure 24VAC Input Input<br />
Input<br />
Thermostat back<br />
Heat Pump HVAC System<br />
Standard HVAC System<br />
Thermostat<br />
Thermostat<br />
Connection<br />
Connection<br />
009-0793-01<br />
SST-W100-00<br />
C 24VAC Common<br />
Optional Feature<br />
R 24VAC Return<br />
Humidifier/Dehumidifier<br />
W1 Aux Heat<br />
O/B Change Over Valve<br />
G Fan<br />
Y1 Compressor Stage 1<br />
Thermostat Setup:<br />
Heat Pump HVAC Systems<br />
Y2 Compressor Stage 2<br />
To set the HVAC system type, go to the Main Menu<br />
Thermostat Info screen and press and hold the Setup button.<br />
Thermostat Setup:<br />
1. Type.<br />
Standard<br />
Set the<br />
Gas/Electric<br />
HVAC System<br />
HVAC<br />
Type:<br />
Systems<br />
set to Heat Pump<br />
To set the HVAC system type, go to the Main Menu Thermostat Info screen<br />
2. C/O type. Change Over (reversing) Valve Type. Heat pumps change from heating to cooling Default by Setup: reversing operation.<br />
and press and hold the Setup button.<br />
�������������������������������������������������������������������<br />
� HVAC Type: Gas/Elec<br />
Check your system information to be sure and note the color of original thermostat wire and � the terminal Fan Type: it was Gas connected to.<br />
1. Type. Set the HVAC System Type: set to Gas/Elec<br />
No matter what the old stat connection was (O or B), connect the wire to the thermostats W2/O � terminal. 2<br />
2. Fan Type. Set the HVAC Fan Type:<br />
The setting of the C/O Type will set the correct system operation.<br />
Set to Gas for typical gas furnace (fan is controlled by the furnace)<br />
For change over with cool systems (Orange wire, O terminal): set C/O type to w/cool (most common and default setting)<br />
Set to Elec for electric heat (fan call with heat call)<br />
For change<br />
3. 2nd<br />
over<br />
Stage<br />
with<br />
Heat.<br />
heat systems<br />
Enable second<br />
(Brown<br />
stage<br />
wire,<br />
heating<br />
B terminal):<br />
outputs<br />
set C/O type to w/heat<br />
3. 2nd Stage Heat. If Enable you have second a single stage stage heating heating outputs system, leave this set to N<br />
If you If have you a have single a 2 stage heating system, set leave to Y this to enable. set to N<br />
If you have a 2 stage heating system, set to Y to enable.<br />
Note! If you get heating when you<br />
4. 2nd Stage Cool. Enable second stage cooling outputs<br />
4. Aux Heat (HP). If you have auxiliary heat strips, set this to Y to enable. expected cooling, change the C/O<br />
If you have a single stage cooling system, leave this set to N.<br />
5. 2nd Stage Cool. Enable second stage cooling outputs<br />
type to the opposite setting.<br />
If you have a two stage cooling system, set to Y to enable.<br />
If you have a single stage cooling system, leave this set to N.<br />
If you have a two stage cooling system, set to Y to enable.<br />
nd Stage Heat: No<br />
� 2 nd Optional Feature<br />
C 24VAC Common<br />
Humidifier/Dehumidifier<br />
R 24VAC Return<br />
W1 Heat Stage1<br />
W2 Heat Stage 2<br />
Common<br />
Contact Closure 24VAC Input<br />
G Fan<br />
Y1 Compressor Stage 1<br />
Y2 Compressor Stage 2<br />
Optional Feature<br />
Dehumidifier<br />
Additional Documentation<br />
Stage Cool: No<br />
Additional Documentation for the SST-W100 and the SST-TEMP1 is available at:<br />
No setup required for this<br />
dealers.<strong>Savant</strong>Systems.com<br />
configuration<br />
<strong>Savant</strong> Hardware > Energy Management<br />
DCN: 141-02048-01 Page 19<br />
DCN: 141-02048-01 Page 20<br />
121912
Change language