BlackandDecker Perceuse S/f- Epl7i - Type H1 - Instruction Manual (Européen)
BlackandDecker Perceuse S/f- Epl7i - Type H1 - Instruction Manual (Européen)
BlackandDecker Perceuse S/f- Epl7i - Type H1 - Instruction Manual (Européen)
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
(Original instructions)<br />
ENGLISH<br />
Vibration<br />
The declared vibration emission values stated in the technical<br />
data and the declaration of conformity have be<strong>en</strong> measured<br />
in accordance with a standard test method provided by<br />
EN 60745 and may be used for comparing one tool with<br />
another. The declared vibration emission value may also be<br />
used in a preliminary assessm<strong>en</strong>t of exposure.<br />
Warning! The vibration emission value during actual use of<br />
the power tool can differ from the declared value dep<strong>en</strong>ding<br />
on the ways in which the tool is used. The vibration level may<br />
increase above the level stated.<br />
Wh<strong>en</strong> assessing vibration exposure to determine safety<br />
measures required by 2002/44/EC to protect persons regularly<br />
using power tools in employm<strong>en</strong>t, an estimation of vibration<br />
exposure should consider, the actual conditions of use and the<br />
way the tool is used, including taking account of all parts of the<br />
operating cycle such as the times wh<strong>en</strong> the tool is switched off<br />
and wh<strong>en</strong> it is running idle in addition to the trigger time.<br />
Labels on tool<br />
The following symbols are shown on the tool:<br />
:<br />
Warning! To reduce the risk of injury, the user<br />
must read the instruction manual.<br />
Additional safety instructions for batteries and<br />
chargers<br />
Batteries<br />
u Never attempt to op<strong>en</strong> for any reason.<br />
u Do not expose the battery to water.<br />
u Do not store in locations where the temperature may<br />
exceed 40 °C.<br />
u Charge only at ambi<strong>en</strong>t temperatures betwe<strong>en</strong> 10 °C and<br />
40 °C.<br />
u Charge only using the charger provided with the tool.<br />
u Wh<strong>en</strong> disposing of batteries, follow the instructions giv<strong>en</strong><br />
in the section "Protecting the <strong>en</strong>vironm<strong>en</strong>t".<br />
p<br />
Do not attempt to charge damaged batteries.<br />
Chargers<br />
u Use your Black & Decker charger only to charge the battery<br />
in the tool with which it was supplied. Other batteries<br />
could burst, causing personal injury and damage.<br />
u Never attempt to charge non-rechargeable batteries.<br />
u Have defective cords replaced immediately.<br />
u Do not expose the charger to water.<br />
u Do not op<strong>en</strong> the charger.<br />
u Do not probe the charger.<br />
$<br />
The charger is int<strong>en</strong>ded for indoor use only.<br />
Read the instruction manual before use.<br />
Electrical safety<br />
Your charger is double insulated; therefore no<br />
earth wire is required. Always check that the<br />
#<br />
mains voltage corresponds to the voltage on the<br />
rating plate. Never attempt to replace the charger<br />
unit with a regular mains plug.<br />
u If the supply cord is damaged, it must be replaced by the<br />
manufacturer or an authorised Black & Decker Service<br />
C<strong>en</strong>tre in order to avoid a hazard.<br />
Features<br />
This tool includes some or all of the following features.<br />
1. On/Off switch<br />
2. Forward/reverse slider<br />
3. Charging indicator<br />
4. Torque adjustm<strong>en</strong>t collar<br />
5. Chuck<br />
Assembly<br />
Warning! Before assembly, remove the battery from the tool.<br />
Fitting and removing a drill bit or screwdriver bit<br />
The drill/screwdriver head is fitted with a keyless chuck to<br />
allow for an easy exchange of bits.<br />
u Lock the tool by setting the forward/reverse slider (2) to<br />
the c<strong>en</strong>tre position (fig. C).<br />
u Op<strong>en</strong> the chuck (5) by turning the front part clockwise with<br />
one hand while holding the rear part with the other.<br />
u Insert the bit shaft into the chuck.<br />
u Firmly tight<strong>en</strong> the chuck (5) by turning the front part anticlockwise<br />
with one hand while holding the rear part with<br />
the other.<br />
This tool is supplied with a double-<strong>en</strong>ded screwdriver bit in the<br />
bit holder (7, fig. A).<br />
u To remove the screwdriver bit from the bit holder, lift the bit<br />
from the recess.<br />
u To store the screwdriver bit, firmly push it into the holder.<br />
Warning! Do not attempt to tight<strong>en</strong> drill bits (or any other accessory)<br />
by gripping the front part of the chuck and turning the<br />
tool on. Damage to the chuck and personal injury may occur<br />
wh<strong>en</strong> changing accessories in this manner.<br />
5