Views
11 months ago

KitchenAid OVN 908 W - OVN 908 W EUR (857923201010) Istruzioni per l'Uso

KitchenAid OVN 908 W - OVN 908 W EUR (857923201010) Istruzioni per l'Uso

61056209.book Page 18

61056209.book Page 18 Friday, March 21, 2008 6:34 PM Changing the rear oven lamp bulb (if provided): 1. Disconnect the oven from the electrical supply. 2. Let the oven cool before turning the lamp cover left to unscrew it (see fig. 1). 3. Change the bulb (see note). 4. Screw the lamp cover back on. 5. Reconnect the oven to the electrical supply. Note: use only 25 W/230 V, E-14 type, T300°C bulbs available from After Sales Service. Important: Do not use the oven until the lamp cover has been repositioned. 1 Changing the side wall lamp (if provided - depends on model): 1. Disconnect the oven from the electrical supply. 2. Let the oven cool before removing the left side runner grid (see fig. 2). Using a screwdriver prise off the lamp cover (see fig. 3 - 4). 3. Change the bulb (see note). 4. Reposition the lamp cover and press it against the oven wall until it clicks correctly into place. 5. Remount the side runner grid. 6. Reconnect the oven to the electrical supply. Note: use only 25 W/230 V, E-14 type, T300°C bulbs available from After Sales Service. Important: Do not use the oven until the lamp cover has been repositioned. 2 Changing the side halogen lamp (if provided - depends on model): 1. Disconnect the oven from the electrical supply. 2. Let the oven cool before removing the side runner grid (see fig. 2). Using a screwdriver prise off the lamp cover (see fig. 3 - 4). 3. Never replace bulbs with bare hands. Carefully remove the halogen lamp from the ceramic holder and replace it with a new one (see note). 4. Reposition the lamp cover and press it against the oven wall until it clicks correctly into place. 5. Remount the side runner grid. 6. Reconnect the oven to the electrical supply. Note: Use only 20 W/12 V, G4 type, T300°C bulbs, available from After Sales Service. Important: Do not use the oven until the lamp cover has been repositioned. 3 4 18

61056209.book Page 19 Friday, March 21, 2008 6:34 PM TROUBLESHOOTING GUIDE Oven not working: • Check for the presence of mains electrical power and if the oven is connected to the electrical supply. • Turn off the oven and restart it to see if the fault persists. IMPORTANT: • Check that the oven control knob is not turned to “0” or to the “lamp” symbol . - If the electronic programmer (depending on model) display presents the message “ ”, consult the product description sheet provided separately and/or the electronic programmer description. - If the electronic programmer (depending on the model) presents the message “F XX”, contact the nearest After Sales Service. Specify in this case the number that follows the letter “F”. - Check that the mechanical programmer (if provided) is turned to “manual”. AFTER SALES SERVICE Before contacting After Sales Service: 1. Try to solve the problem yourself following the points described in “Troubleshooting Guide”. 2. Turn off the appliance and restart it to see if the fault persists. If after the above checks the oven or cooktop are still not working properly, contact the nearest After Sales Service. Please give: • A short description of the fault; • the oven type and model; • the service number (number after the word Service on the rating plate), located on the right hand edge of the oven cavity (visible when the oven door is open). The service number is also indicated on the guarantee booklet; • your full address; • your phone number. In the event the oven must be repaired, contact an authorised After Sales Service, (use of original replacement parts and proper repair is guaranteed). Failure to comply with these instructions may compromise the safety and quality of the product. DECLARATION OF CONFORMITY • This oven is designed to come into contact with food and complies with regulation (EC) no.1935/2004. • This appliance is designed to be used for cooking only. Any other use (for example, for room heating) is considered as improper use and potentially dangerous. • The appliance was designed, manufactured and sold in compliance with: - the safety requirements of “Low Voltage” Directive 2006/95/EC (replacing 73/23 EEC as amended); - the protection requirements of EMC Directive 89/336/EEC; - the requirements of Directive 93/68/EEC. 19