Views
2 months ago

Sony STR-DN840 - STR-DN840 Istruzioni per l'uso Inglese

Sony STR-DN840 - STR-DN840 Istruzioni per l'uso Inglese

Setting the speakers To

Setting the speakers To set the surround back speakers You can switch the usage of the speaker(s) connected to the SURROUND BACK/ BI-AMP/FRONT HIGH/FRONT B terminals in accordance with the intended use. Note This setting is only available if the “Speaker Pattern” is set to a setting without surround back and front high speakers. 1 Press HOME. The home menu is displayed on the TV screen. 2 Press V/v repeatedly to select “Settings”, then press . 3 Press V/v repeatedly to select “Speaker Settings”, then press . 4 Press V/v repeatedly to select “SB Assign”, then press . 5 Select the speaker setup that you want, then press . • Speaker B: If you connect an additional front speaker system to the SURROUND BACK/BI-AMP/ FRONT HIGH/FRONT B terminals, select “Speaker B”. • Bi-Amp: If you connect front speakers to the SURROUND BACK/BI-AMP/ FRONT HIGH/FRONT B terminals using a bi-amplifier connection, select “Bi-Amp”. • Off: If you connect surround back or front high speakers to the SURROUND BACK/BI-AMP/ FRONT HIGH/FRONT B terminals, select “Off”. To select the front speaker You can select the front speakers you want to drive. Be sure to use the buttons on the receiver to perform this operation. SPEAKERS Press SPEAKERS repeatedly to select the front speaker system you want to drive. You can confirm the selected speakers terminals by checking the indicator on the display panel. Indicators Selected speakers SP A SP B* SP A+B* The speaker connected to the SPEAKERS FRONT A terminals. The speaker connected to the SPEAKERS SURROUND BACK/ BI-AMP/ FRONT HIGH/ FRONT B terminals. The speaker connected to both the SPEAKERS FRONT A and SPEAKERS SURROUND BACK/ BI-AMP/ FRONT HIGH/ FRONT B terminals (parallel connection). “SPK OFF” appears on the display panel. No audio signals are output from any speaker terminals. * To select “SP B” or “SP A+B”, set the “SB Assign” to “Speaker B” in the Speaker Settings menu (page 84). Note This setting is not available when headphones are connected. 34 GB

To cancel Auto Calibration The Auto Calibration function will be canceled when you perform the following during the measurement process: – Press ?/1. – Press the input buttons on the remote control or turn the INPUT SELECTOR on the receiver. – Press . – Press SPEAKERS on the receiver. – Change the volume level. – Connect the headphones. To set up the receiver manually See “Adjusting Settings” (page 80). Configuring the network settings of the receiver The network settings for the receiver must be set correctly to use the Home Network, SEN, AirPlay, and PARTY STREAMING functions. Using a wired LAN connection DISPLAY V/v/B/b, HOME 1 Press HOME. The home menu is displayed on the TV screen. 2 Press V/v repeatedly to select “Settings”, then press . 3 Press V/v repeatedly to select “Network Settings”, then press . 4 Press V/v repeatedly to select “Internet Settings”, then press . 5 Press V/v repeatedly to select “Wired Setup”, then press . If “Change Settings?” appears on the TV screen, select “OK”, then press . 6 Press V/v repeatedly to select “Auto”, then press . IP settings information appears on the TV screen. When using a fixed IP address Select “Custom”, then press . The IP Address Setting appears on the TV screen. Press . Press V/v to select the value for “IP Address”. Press b to key in the value for the next position. Press to exit cursor. Next, enter the value for “Subnet Mask” and “Default Gateway”. Press b for DNS Settings page. Then enter the value for “Primary DNS” and “Secondary DNS”. 7 Press b. “Connecting to the Internet” appears on the TV screen. “Network setup is completed” appears after the network settings are completed. To return to the Network Settings menu, press . (Depending on the network environment, the network settings may take some time.) 8 Perform the server settings. To listen to audio content stored on the server, you need to set up your server (page 55). Tip When checking the network settings, see “Information” (page 90). Preparing the Receiver 35 GB