valmislaasti spezial-beton - Pagel Spezial-Beton GmbH & Co. KG
valmislaasti spezial-beton - Pagel Spezial-Beton GmbH & Co. KG
valmislaasti spezial-beton - Pagel Spezial-Beton GmbH & Co. KG
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
TW PAGEL-VALMISLAASTI JUOMAVESI YMPÄRISTÖÖN<br />
TUOTTEET<br />
• TW05 PAGEL-DRINKING WATER SCREEDING COMPOUND 0– 0,5 mm<br />
• TW10 PAGEL-VALMISLAASTI 0– 1,0 mm<br />
• TW20 PAGEL-VALMISLAASTI 0– 2,0 mm<br />
• TW40 PAGEL-VALMISLAASTI 0– 4,0 mm<br />
• TW05 PAGEL-DRINKING WATER SCREEDING COMPOUND (valkoinen) 0– 0,5 mm<br />
• TW10 PAGEL-VALMISLAASTI (valkoinen) 0– 1,0 mm<br />
• TW20 PAGEL-VALMISLAASTI (valkoinen) 0– 2,0 mm<br />
• TW40 PAGEL-VALMISLAASTI (valkoinen) 0– 4,0 mm<br />
OMINAISUUDET<br />
• Vastaa työohjeita W270, W300 ja W347 DVGW:<br />
ssä ja on myös käyttökelpoinen mikrobiologian<br />
juomavesi ympäristössä<br />
• Ehkäisee mikrobien kasvamista , lisäksi<br />
ehkäisee bakteerien ja sienien esiintymistä<br />
• On Microsilikalla rikastettu<br />
• Voidaan käyttää vaaka- ja pystypinnoille.<br />
Voidaan myös pinnoittaa märkä- ja kuivaruiskutus<br />
menetelmillä<br />
• can be applied using dense phase wet and dry spraying<br />
• Use of the MAWO nozzle for dense phase wet spraying<br />
ensures marginal rebound and very little dust<br />
• in respect of water behaviour meets the demands on<br />
container materials specified in the "Plastic Drinking<br />
Water Recommendations" of the Bundesgesundheitsamt<br />
(Federal Health Service) TW (white)<br />
TYÖSTÖ<br />
SUBSTRATE: Thoroughly clean, remove loose and ahesion-checking<br />
parts as well as cement slurry by high-pressure-water<br />
blasting or such like down to the loadbearing grain<br />
structure, sufficient abrasion resistance must be guaranteed<br />
(i. M. � 1,5 N/mm 2 , KEW � 1,0 N/mm 2 ).<br />
Pre-wetting: Pre-wet for approx. 6 - 24 hours until capillary<br />
saturation of the concrete substrate.<br />
Reinforcing steel: Blast all rust off exposed reinforcement<br />
bars until the underlying metal has been exposed to Sa 2 1/2<br />
in accordance with DIN EN ISO 12944-4.<br />
CORROSION PROTECTION: Apply two complete coats of<br />
TW05 PAGEL DRINKING WATER SCREE-<br />
DING COMPOUND to the derusted reinforcing steel<br />
using a brush.<br />
BONDING LAYER: Use a hard bristle sweeping or scrubbing<br />
brush and brush TW10 PAGEL DRINKING<br />
WATER MORTAR onto the pre-wetted, slightly damp<br />
concrete substrate until it has penetrated right down into the<br />
pores and without leaving any gaps. The next mortar layer<br />
must be applied immediately wet on wet. If applied using<br />
spraying technology, TW MORTARS do not require<br />
bonding layers.<br />
SEKOITUS: Sekoitetaan pakkosekoittimessa, johon laitetaan<br />
2/3 vesimäärästä, lisätään laastijauhe ja lyhyen<br />
sekoituksen n. 3 min. jälkeen lisätään loput vedestä. Tämän<br />
jälkeen sekoitetaan vielä n. 2 minuuttia.<br />
Mixing water: drinking water quality<br />
PROCESSING: Apply TW40 in plastic consistency in<br />
the not yet set adhesion primer, disperse and smooth. If<br />
using the spray process, seek special technical advice if<br />
requird.<br />
KÄYTTÖALUE<br />
• Seinien ja lattioiden pinnoittamiseen juomavesi<br />
ympäristössä<br />
• <strong>Beton</strong>in, rappauksien ja<br />
lattioiden korjaamiseen<br />
• Juomavesisäiliöihin, putkiin,<br />
puhdistuslaitoksiin<br />
• <strong>Co</strong>atings used in the food industry<br />
FINISHING: Exposed areas of mortar must be protected<br />
from premature water evaporation such as from wind,<br />
draughts, direct exposure to sun, immediately on completion<br />
of the work for a period of 3-5 days.<br />
Suitable finishing methods: Spray with water, cover with jute<br />
sheets, insulation material or moisture-retaining materials.<br />
Limit temperatures for application (surface, air and mortar<br />
temperature): +5 °C to +35 °C:<br />
Low temperatures and cold mixing water will delay strength<br />
development, will make it harder to mix the materials (requires<br />
the use of a compulsory mixer) and reduce flowability,<br />
while high temperatures accelerate strength development.<br />
Take note of the surface’s dew point temperature.<br />
Non-Iron-Metals: Cement and cement-bound building<br />
materials cause non-iron-metals that are inside the area of<br />
application (e.g. aluminium, copper, zinc) to loosen. Please<br />
contact us for technical advice.<br />
MÄRKÄRUISKUTUSMENETELMÄ<br />
TW05,TW10,TW20,TW40<br />
TARTUNTASILTA: Tartuntasilta ei ole välttämätön<br />
PINNOITUS: Märkäruiskutusmenetelmä; laastien pinnoitus<br />
voidaan suorittaa tavanomaisilla monopumpuilla<br />
SUUTINJÄRJESTELMÄ:<br />
MAWO-SUUTIN<br />
PAINEILMAKOMPRESSORI:<br />
� 5 m 3 /min<br />
� 5 bar<br />
SYÖTTÖLETKU:<br />
Kuljetuspituus: max. 40 m<br />
Letkun halkaisija: 35 mm<br />
Letkun pään<br />
supistaminen: 5-6 m Ø 25 mm