Vis à métaux à tête cylindrique ET RONDE
Vis à métaux à tête cylindrique ET RONDE
Vis à métaux à tête cylindrique ET RONDE
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Nom : III.<strong>Vis</strong> <strong>à</strong> <strong>métaux</strong> <strong>à</strong> <strong>tête</strong> <strong>cylindrique</strong> <strong>ET</strong> <strong>RONDE</strong> PJ<br />
4. <strong>Vis</strong> <strong>à</strong> <strong>métaux</strong> <strong>à</strong> <strong>tête</strong> <strong>cylindrique</strong> bombée large <strong>à</strong> empreinte cruciforme de type<br />
H ou de type Z grade A, extrait norme NF EN ISO 7045<br />
Figure 13<br />
• Matériaux : acier, acier inoxydable et <strong>métaux</strong> non ferreux (sans finition particulière).<br />
• Tolérance du filetage : 6g.<br />
• Principales classes de qualité : 4.8 pour les aciers ; A2-50 et A2-70 pour les inoxydables.<br />
Exemple de désignation : vis <strong>à</strong> <strong>tête</strong> <strong>cylindrique</strong> bombée large ISO 7045 - M5 x 20 - 4.8 Z (pour une<br />
vis <strong>à</strong> <strong>tête</strong> <strong>cylindrique</strong> large bombée, <strong>à</strong> empreinte cruciforme de type Z, de filetage M5, de longueur nominale<br />
L=20 mm et de classe de qualité 4.8).<br />
<strong>Vis</strong> <strong>à</strong> <strong>métaux</strong> <strong>à</strong> <strong>tête</strong> <strong>cylindrique</strong> bombée large, empreinte cruciforme<br />
de type H ou de type Z - grade A - NF EN ISO 7045 Tableau 14<br />
Fletage t pas a m b mini s maxi L (mm) : vis entièrement filetées<br />
(d) mm mm mm mm mm mm mm L* : vis partiellement filetées<br />
M1,6 3,2 0,35 1,3 1,6 25 0,7 3-4-5-6-8-10-12-(14)-16<br />
M2 4,0 0,4 1,6 2,1 25 0,8 3-4-5-6-8-10-12-(14)-16-20<br />
M2,5 5,0 0,45 2,1 2,6 25 0,9 3-4-5-6-8-10-12-(14)-16-20-25<br />
M3 5,6 0,5 2,4 3,0 25 1 4-5-6-8-10-12-(14)-16-20-25-30<br />
M3,5* 7,0 0,6 2,6 3,9 38 1,2 5-6-8-10-12-(14)-16-20-25-30-35<br />
M4 8,0 0,7 3,1 4,4 38 1,4 5-6-8-10-12-(14)-16-20-25-30-35-40<br />
M5 9,5 0,8 3,7 4,9 38 1,6 6-8-10-12-(14)-16-20-25-30-35-40-45*<br />
M6 12,0 1 4,6 6,9 38 2 8-10-12-(14)-16-20-25-30-35-40-45*-<br />
50*-(55*)-60*<br />
M8 16,0 1,25 6,0 9 38 2,5 10-12-(14)-16-20-25-30-35-40-45*-50*-<br />
55*-60*<br />
M10 20,0 1,5 7,5 10 38 3 12-(14)-16-20-25-30-35-40-45*-50*-<br />
(55*)-60*<br />
* filetages non préférentiels - les dimensions entre parenthèses sont <strong>à</strong> éviter<br />
VIS A T<strong>ET</strong>E CYLINDRIQUE.doc P.JOHO Page 4