LWM1™ - Files

More documents

Recommendations

Info

Replacing the fuse after melt-through. Replacing the fuse is possible without opening the module! (if the module has been opened the guarantee no longer applies). Remove the film above the fuse and then pull the fuse out of the module with pointed pliers. Replace the fuse with a fuse of one of the following types (with the application of other types the guarantee no longer applies): Supplier dimmer fuse Description Order number supplier Littelfuse LT-5 ALg 0663.01.6 Bussman ETF Radial Lead Micro Fuse BK ETF1.6 ELU Sub miniature fuse links 166050-1,6AT Wickmann Subminiatur fuse No 372.TR5 372-1160-041 Bel fuse Time Lag Radial Lead Micro Fuse MTR1,6 short leads NEVER CONNECT A WOUND VOLTAGE TRANSFORMER TO THE LWM1 WHILE THE VOLTAGE IS SWITCHED ON. THE FUSE CAN MELT AS A RESULT. LOW VOLTAGE HALOGEN LIGHTING The LWM1 can only be used in combination with the electronic transformer suitable for leading-edge phase dimmers. The LWM1 cannot be coupled to transformers suitable for trailing-edge phase dimmers. Coupling it to such a transformer will cause a humming sound and damage the LWM1. The right to guarantee will also expire as a result. 14 © MARMITEK
FREQUENTLY ASKED QUESTIONS What is the reason for modules to switch on/off spontaneously? It is possible that a Marmitek X-10 System is installed at one of your neighbours using the same House Code. To solve this problem try to change the House Code of your system, or have FD10 Phase Coupler/Filter installed at your incoming mains. ENGLISH My modules will not respond to my controller. Make sure that the House Code on all Modules and Controllers are set to the same House Code (A .. P). My modules will not react to my remote / sensor. When you use a remote or sensor, you should have at least one TM13 Transceiver or Marmitek Security Console installed in your house. These components will translate the radio signals to the Marmitek X-10 signal on the power line. Only one Transceiver should be installed for all remotes and sensors set to the same House Code. Am I able to increase the range of my remotes by using more Transceivers? Yes, you can use more than one TM13 Transceiver in your home when the range of your remotes is not sufficient. The TM13 is using so called collision detection to prevent signals to be disturbed when more than one TM13 is transmitting. TM13’s will wait for a quite power line before transmitting their data. To prevent your Marmitek X-10 System to become slow or to prevent dimming from becoming less smooth, make sure that the TM13 units are placed as far away from each other as possible. The module suddenly starts to blink for a short time. Electronic dimmers, such as the LWM1, make use of cutting in or cutting off the sine in order to transform voltage. In an unstable mains system, or as a consequence of short low frequency pulses, the shape of the sine can be disrupted, resulting in light variations. This phenomenon does not harm the modules. LWM1 TM 15
Page 1 and 2: LWM1 MICRO MODULE WITH DIMMER USER
Page 3 and 4: LWM1 BUILT-IN DIMMER MODULE SAFETY
Page 5 and 6: ADRESSES Up to a maximum of 256 dif
Page 7 and 8: INSTRUCTIONS FOR USE - LWM1 BUILT-I
Page 9 and 10: “2-way momentary switch” Push t
Page 11 and 12: PROGRAMMING WARNING: DO NOT FORGET
Page 13: first!! (e.g. E4). • Make sure th
Page 17 and 18: TECHNICAL DATA Power: Capacity: 230
Page 19 and 20: LWM1 EINBAU-DIMMERMODUL SICHERHEITS
Page 21 and 22: kann auch an den Reglern eingestell
Page 23 and 24: versehen. Diese Filter formen eine
Page 25 and 26: Blau Rod Braun N PROG. LWM1 L Phase
Page 27 and 28: Phase 230V Null Shaltkabel. Auf die
Page 29 and 30: In dem nachstehenden Beispiel gehen
Page 31 and 32: Entfernen Sie die Folie über der S
Page 33 and 34: einer 8-in-1 Multi-Media Fernbedien
Page 35 and 36: LWM1 MODULE GRADATEUR ENCASTRABLE
Page 37 and 38: ADRESSES Vous pouvez programmer jus
Page 39 and 40: chacune des phases de votre maison.
Page 41 and 42: Bleu Rouge Marron N PROG. LWM1 L Ph
Page 43 and 44: Jarretière de connexion. La charge
Page 45 and 46: L’adresse ainsi que les options p
Page 47 and 48: Enlever l’autocollant sur le fusi
Page 49 and 50: • Pour sortir appuyer sur la touc
Page 51 and 52: REGULADOR DE LUZ EMPOTRADO LWM1 AVI
Page 53 and 54: subdivididas en el llamado Código
Page 55 and 56: las señales que entren o dejen su
Page 57 and 58: Azul Rojo Marrón N PROG. LWM1 L Fa
Page 59 and 60: Cable de interruptor. A este cable
Page 61 and 62: Programación de las direcciones y
Page 63 and 64: Reemplazar un fusible fundido ¡El
Page 65 and 66:
El módulo empieza a encenderse y a
Page 67 and 68:
LWM1 MODULO AD INCASSO PER REGOLARE
Page 69 and 70:
tramite le apposite rotelline per i
Page 71 and 72:
fasi in ingresso dei Filtri Accoppi
Page 73 and 74:
Blu Rosso Marrone N PROG. LWM1 L Fa
Page 75 and 76:
Zero Fase 230V Filo: Il carico è c
Page 77 and 78:
L’indirizzo e le opzioni possono
Page 79 and 80:
Fornitore fusibile Descrizione Nume
Page 81 and 82:
• premere il tasto [2]. • due v
Page 83 and 84:
Informazioni relative all’ambient
Page 85 and 86:
LWM1 INBOUW DIMMERMODULE VEILIGHEID
Page 87 and 88:
(1 t/m 16). De HuisCode is ook inst
Page 89 and 90:
GEBRUIKSAANWIJZING LWM1 INBOUW DIM
Page 91 and 92:
“2 vlaks Pulsdrukschakelaar”: T
Page 93 and 94:
PROGRAMMEREN LET OP: EERST DE SPANN
Page 95 and 96:
Voorbeeld van het programmeren van
Page 97 and 98:
VEEL GESTELDE VRAGEN Hoe komt het d
Page 99 and 100:
TECHNISCHE GEGEVENS Voeding: 230V -
Page 101 and 102:
DECLARATION OF CONFORMITY Marmitek
show all

LWM1™ - Files

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?