BlackandDecker Lampe- Fsl144 - Type H2 - Instruction Manual (la Hongrie)
BlackandDecker Lampe- Fsl144 - Type H2 - Instruction Manual (la Hongrie)
BlackandDecker Lampe- Fsl144 - Type H2 - Instruction Manual (la Hongrie)
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
ENGLISH<br />
Other batteries could burst, causing personal injury<br />
and damage.<br />
♦ Never attempt to charge non-rechargeable<br />
batteries.<br />
♦ Have defective cords rep<strong>la</strong>ced immediately.<br />
♦ Do not expose the charger to water.<br />
♦ Do not open the charger.<br />
♦ Do not probe the charger.<br />
This appliance is intended for indoor use<br />
only.<br />
Read all of this instruction manual carefully.<br />
The charger automatically shuts off if the<br />
ambient temperature becomes too high. As<br />
soon as the ambient temperature has cooled<br />
down, the charger will resume operating.<br />
Charge only at ambient temperatures<br />
between 10 °C and 40 °C.<br />
Features<br />
This appliance has the following features:<br />
1. On/off switch<br />
2. Carrying strap<br />
3. Battery<br />
Fig. A, C and D<br />
4. Battery release button<br />
5. Charger<br />
6. Charger receptacle<br />
7. Charger connector<br />
8. Charger plug<br />
Assembly<br />
Warning! Before assembly, remove the battery<br />
from the appliance.<br />
Fitting and removing the battery (fig. A)<br />
♦ To fi t the battery (3), line it up with the receptacle<br />
on the appliance. Slide the battery into the<br />
receptacle and push until the battery snaps into<br />
p<strong>la</strong>ce.<br />
♦ To remove the battery, push the release button<br />
(4) while at the same time pulling the battery out<br />
of the receptacle.<br />
Fitting the battery cap (fig. B)<br />
Warning! Fit the cap (9) to the battery (3) for<br />
transportation and storage.<br />
Charging the battery<br />
The battery needs to be charged before fi rst use<br />
and whenever it fails to produce suffi cient power on<br />
jobs that were easily done before. When charging<br />
the battery for the fi rst time, or after prolonged<br />
storage, it will only accept an 80% charge. After<br />
several charge and discharge cycles, the battery<br />
will attain full capacity. The battery may become<br />
warm while charging; this is normal and does not<br />
indicate a problem.<br />
Warning! Do not charge the battery at ambient<br />
temperatures below 10 °C or above 40 °C.<br />
Recommended charging temperature: approx.<br />
24 °C.<br />
Charging with the charger receptacle (fig. C)<br />
♦ To charge the battery (3), remove it from the<br />
appliance and slide the charger receptacle (6)<br />
onto the battery.<br />
♦ Plug in the charger (5).<br />
After normal use, a charging time of 3 hours will<br />
provide sufficient power for most applications.<br />
However, further charging for up to 6 hours could<br />
signifi cantly increase the use time, depending on<br />
the battery and charging conditions.<br />
♦ Remove the charger receptacle (6) from the<br />
battery (3).<br />
Charging with the charger plug (fig. D)<br />
♦ To charge the battery, make sure that it is fi tted<br />
on the appliance.<br />
♦ Insert the charger plug (8) into the charger<br />
connector (7).<br />
♦ Plug in the charger (5).<br />
♦ Switch the charger on at the mains supply.<br />
After normal use, a charging time of 3 hours will<br />
provide sufficient power for most applications.<br />
However, further charging for up to 6 hours could<br />
signifi cantly increase the use time, depending on<br />
the battery and charging conditions.<br />
♦ Disconnect the charger connector (8) from the<br />
appliance.<br />
Warning! Do not use the appliance while it is<br />
connected to the charger.<br />
Rep<strong>la</strong>cing the bulb (fig. E)<br />
The bulb can be rep<strong>la</strong>ced easily.<br />
Warning! Do not touch the bulb shortly after using<br />
the fl ashlight, as the bulb may be hot.<br />
♦ Remove the battery (3).<br />
♦ Remove the bulb holder (10) by turning it counter<br />
clockwise.<br />
♦ Remove the bulb (11) by turning it slightly and<br />
pulling it out of the bulb holder (10).<br />
♦<br />
♦<br />
Insert a new bulb.<br />
Re-fi t the bulb holder (10) into the fl ashlight and<br />
turn it clockwise to secure it.<br />
Maintenance<br />
Your B<strong>la</strong>ck & Decker appliance has been designed<br />
to operate over a long period of time with a minimum<br />
of maintenance. Continuous satisfactory operation<br />
11