BlackandDecker Tondeuse Rotative- Emax38 - Type 2 - Instruction Manual (l'Indonésie)
BlackandDecker Tondeuse Rotative- Emax38 - Type 2 - Instruction Manual (l'Indonésie)
BlackandDecker Tondeuse Rotative- Emax38 - Type 2 - Instruction Manual (l'Indonésie)
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
(Original instructions)<br />
ENGLISH<br />
Warning! Use heavy-duty gloves to grip the blade.<br />
To remove the blade:<br />
Turn the appliance onto its side.<br />
Using heavy-duty gloves, grip the blade.<br />
Use a 13mm spanner to loosen and remove the blade bolt<br />
(25) by turning the spanner anti-clockwise (ac).<br />
Remove the blade (26) and blade bolt (25).<br />
To replace the blade:<br />
Offer the blade up to bolt shaft and locate the blade bolt<br />
(25) into the bolt shaft.<br />
Note:<br />
facing the user.<br />
<br />
Using heavy-duty gloves, grip the blade.<br />
Use a 13mm spanner to securely tighten the blade bolt<br />
(25) by turning the spanner clockwise (c).<br />
Use<br />
Warning! Let the appliance work at its own pace. Do not<br />
overload.<br />
The height of cut is adjusted by the central height adjust<br />
mechanism, there are 6 positions to choose from.<br />
To set the height of cut<br />
Pull the height adjustment lever (7) away from the body of<br />
the unit.<br />
Move the lever towards the rear of the appliance to lower<br />
the height of cut.<br />
Move the lever towards the front of the appliance to raise<br />
the height of cut.<br />
Push the height adjustment lever (7) into one of the 6<br />
height locations.<br />
Note: The height of cut can be viewed on the height of cut<br />
gauge (8) on the side of the unit.<br />
Switching on<br />
Push in and hold the lock-off button (27).<br />
Pull the on/off switch (2) towards the handle.<br />
Release the lock-off button.<br />
Switching off<br />
Release the on/off switch (2).<br />
Warning: Never attempt to lock a switch in the on position.<br />
We recommend to use your mower as outlined in this section<br />
in order to achieve optimum results and to reduce the risk of<br />
cutting the mains cable.<br />
)<br />
Loop the mains cable through the intelligent cable<br />
leave approximately 100 cm of cable between the switchbox<br />
(1) and the intelligent cable management restraint (4).<br />
Ensure that the cable restraint can slide freely from one<br />
handle to the other.<br />
Place the bulk of the mains cable on the lawn, close to the<br />
Switch the appliance on as described above.<br />
<br />
Move from position 1 to position 2.<br />
Turn right, stepping over the cable and proceed towards<br />
position 3. The cable restraint will slide from one side of<br />
the handle to the other ensuring that the cable is laid out<br />
away from the cutting blade.<br />
Turn left, stepping over the cable and move towards position<br />
4. The cable restraint will slide from one side of the<br />
handle to the other ensuring that the cable is laid out away<br />
from the cutting blade.<br />
Repeat the above procedure as required.<br />
Warning:<br />
We recommend to use your mower as outlined in this section<br />
in order to achieve optimum results and to reduce the risk of<br />
cutting the mains cable.<br />
Place the bulk of the mains cable on the lawn, close to the<br />
Switch the appliance on as described above.<br />
<br />
Move from position 1 to position 2.<br />
Turn right and proceed towards position 3.<br />
Turn left and move towards position 4.<br />
Repeat the above procedure as required.<br />
Warning:<br />
EdgeMax allows you to cut grass right up to the edge of a wall<br />
EdgeMax allows you to accurately cut grass right up to the<br />
With the lawnmower parallel with the edge of your lawn.<br />
Push the lawnmower along the edge of the lawn. Ensure<br />
that the EdgeMax (9) is slightly over the edge of your lawn<br />
only)<br />
When the grass collection box is full you can compact the<br />
grass in the collection box. You can determine how full the<br />
(11).<br />
Release the on/off switch (2).<br />
5