Philips 3200 series Téléviseur LED - ERP Power consumption declaration - ENG
Philips 3200 series Téléviseur LED - ERP Power consumption declaration - ENG
Philips 3200 series Téléviseur LED - ERP Power consumption declaration - ENG
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
42PFL3207<br />
For clarification: j.bhat@philips.com Report reference number: 2012-<strong>ERP</strong>-50PFL307T<br />
A. General info :<br />
Equipment under test:<br />
42PFL3207H/12<br />
Model(s) covered under the Energy Label<br />
42PFL3207H/12<br />
Energy Label : Model Name 42PFL3207<br />
Energy Label : Phome in Watts 59<br />
Fill up LHS rows ; only if Energy<br />
Energy Label : Annual Energy Consumption in KWhr 87<br />
label is finalised<br />
Energy Label : Energy Class<br />
A<br />
Date : January 17, 2012<br />
Visible screen diagonal in inches<br />
40 Type only number in LHS block<br />
Light sensor feature in TV yes 0<br />
Hard switch / tack switch to put the set in OFF mode<br />
yes<br />
Dig. & Anlg.reception orSatellite Tuner or 2nd tuner<br />
Panel brand/model<br />
Standard(s) :<br />
Equipment ( calibrated ) :<br />
Signal :<br />
2K12 Europe Sustainability Technical Documentation ( Final )<br />
B. Measurement conditions<br />
LG/LC320EUE-SEM1<br />
1. Minolta Color Analyzer CA-210<br />
2.Yokogama WT210 Digital <strong>Power</strong> Meter.<br />
3. <strong>Philips</strong> BDP8000<br />
Conditions :<br />
1. Reading is done after value has stabilized (delta between 2 consecutive measurements < 0.5%<br />
)<br />
2. Measurement according to IEC 62087 ed2.0, section 5.<br />
Dynamic Broadcast :<br />
Test_Disk_All_Scenes_Edited_to_10_min_No_Ads<br />
(According IEC62087 clause 11.6)<br />
Measurement Mode :<br />
Average power <strong>consumption</strong> (accuracy to 0.01W)<br />
Mains voltage : Vac=240V THD= 0.13%<br />
Frequency :<br />
50Hz<br />
Ambient Temperature : 23°C<br />
Input Terminal :<br />
HDMI<br />
C. Set model conditions : For Test D,E and F<br />
Upscaling/processing by AV player<br />
Ambilight ( Default = ON ) :<br />
Light Sensor ( Default = ON ) :<br />
Sound Output ( 1kHz tone ) :<br />
Picture Mode ( Default = Factory Settings )<br />
View Mode:<br />
OFF<br />
OFF<br />
OFF<br />
>50mW<br />
Standard<br />
Widescreen<br />
D. Test results :<br />
IEC 62087/Ed. 2.0<br />
Dynamic Broadcast (Po Broadcast ) : On mode (W) 36.3 PASS<br />
Standby power ( 10 min average) (W) 0.07 PASS<br />
Off mode power ( 10 min average) (W) 0.07 PASS<br />
E. Average result of static signals :<br />
Peak luminance home-mode (Nits) 320<br />
Peak luminance of brightest on-mode (Nits) 490<br />
Peak luminance ratio 65.3% PASS<br />
F. Other information :<br />
Auto power down after X minutes 240 PASS<br />
Presence of alert message before Auto shut down yes PASS<br />
Hazardous substance - Mercury (mg) 0<br />
Hazardous substance - Lead (present/not present)<br />
present<br />
G. Additional compliance test: Test Condition : Static picture ; default Out of box mode<br />
Is light sensor ON; in default out of Box mode yes PASS<br />
Ambient light = Room light(About 300 lux); Peak<br />
luminance home-mode (Nits)<br />
Ambient light =