Save Our PDF Price List 2012-13 in - Suvchem

R
PTFE JAR Type
Size OD
X LT
Unit Price
50 ML 50 X 46 13.50
100 ML 54 X 68 25.00
250 ML 70 X 95 50.00
500 ML 85 X 120 80.00
1000 ML 110 X 150 130.00
2000 ML 130 X 200 290.00
5000 ML 175 X 250 520.00
PTFE JAR WITH INTERCHANGABLE SCREW
CAP
PTFE TEST TUBE RACK Type Size Unit Price
HOLES DIA HT
27 8 45 48.00
21 13 60 48.00
10 19 70 48.00
4 30 80 48.00
STANDARD SIZE: 180 X 160 X 80
CUSTOM DESIGN WELCOME
PTFE EVAPORATING DISH Type
Size OD
X LT
Unit Price
TALL FORM WITH SPOUT
25 ML 38 X 34 8.80
50 ML 40 X 50 20.00
100 ML 64 X 50 37.00
150 ML 78 X 43 55.00
180 ML 80 X 50 65.00
250 ML 97 X 50 90.00
350 ML 100 X 60 125.00
FLAT FORM
25 ML 42 X 25 6.50
50 ML 60 X 20 13.50
100 ML 80 X 28 12.50
180 ML 78 X 46 36.00
PTFE BOTTLE Type Size
HEIGHT
OD -MT
Unit Price
10 ML 50 26- 12 15.50
25 ML 61 33 - 19 19.00
50 ML 76 43 - 25 25.00
100 ML 88 52 - 35 40.00
150 ML 90 60 - 35 46.00
250 ML 115 67 - 42 50.00
500 ML 150 80 - 52 95.00
1000 ML 185 100 - 57 170.00
2000 ML 240 120 - 60 290.00
NARROW MOUTH + 10%
WITH SCREW CAP ORING OPTIONAL
ALL PRODUCTS FOR LAB USE ONLY (NOT FOR DRUG / MEDICNAL / HOUSEHOLD USE)
sales@suvchem.com
84.00
70
PTFE TEST TUBE Type
Size
OD X LT
Unit Price
5 ML 16 X 75 8.00
10 ML 16 X 100 10.00
15 ML 20 X 100 11.00
20 ML 22 X 100 12.00
25 ML 24 X 100 13.00
50 ML 25 X 170 16.00
100 ML 30 X 200 21.00
TEST TUBE OF DIFFERENT TYPE WITHOUT CAP,
FLAT BOTTOM, ROUND BOTTOM, CONICAL
BOTTOM. ADD 10% FOR SCREW CAP
PTFE FUNNEL
PTFE DRYING TRAY
PTFE TWEEZERS
PROPERTIES OF SUV PTFE LABWARE PRODUCTS
Type Size
Height
Unit Price
DIAMETER STEM DIA
30 MM 8 MM 50 MM 8.00
50 MM 10 MM 85 MM 13.00
70 MM 12 MM 110 MM 24.00
100 MM 14 MM 170 MM 47.00
150 MM 16 MM 220 MM 78.00
Size
L X W X T
Unit Price
250 X 150 X 50 240.00
200 X 100 X 50 125.00
150 X 150 X 40 115.00
TRAYS AS PER CUSTOM DESIGN
CAN ALSO BE MADE
Size
LENGTH
Unit Price
100 MM SHARP 20.00
150 MM SHARP 28.00
200 MM SHARP 36.00
100 MM SQUARE 22.00
150 MM SQUARE 30.00
200 MM SQUARE 38.00
PTFE FLASK Type
SIZE
OD X HT
NECK ID Unit Price
25 ML 42 X 70 21 8.00
50 ML 51 X 82 21 16.00
100 ML 64 X 105 25 26.00
150 ML 72 X 124 28 32.00
250 ML 85 X 140 34 47.00
500 ML 104 X 176 34 78.00
1000 ML 131 X 220 42 156.00
NARROW MOUTH + 10%
WITH SCREW CAP + 15%
ROUND BOTTOM + 10%
Non - Stick Very few solid substances will permanently adhere to a "SUV" coating. And while tacky materials may show some adhesion, allmost all substances release easily.
Non - Wetting Since "SUV" surfaces are both oleo phobic and hydrophobic, they are not readily wet. Clean-up is easier, more through and in many cases self-cleaning.
Heat Resistance There is no decomposition of "SUV" finishes below 400o F; insignificant decomposition between 400 and 500 F which requires no special precautions. From 500 to
575 F, intermittent service is possible with adequate ventilation.
Low Coefficient of The coefficient of friction of "SUV" is generally in the range of 0.05 to 0.20, depending upon the load, sliding speed and particular "SUV" finish used.
Friction
Cryogenic Stability Many "SUV" will withstand severe temperatures extremes without loss of physical properties. "SUV" may be considered for use at temperatures as low as -450o F.
Unique Electrical
Properties
Over a wide range of frequencies, "SUV" has high dielectric strength, a low dissipation factor, and very high surface resistivity. By special techniques, it can be made
conductive enough to be used as an anti-static coating.
Chemical Resistance "SUV" is normally unaffected by chemical environments. However, certain coatings are permeable or have a lower resistance to attack. The only chemicals known to
affect all "SUV" finishes are the alkali metals and highly reactive fluorinating agents.