BlackandDecker Tagliabordi A Filo- Gl720 - Type 5 - Instruction Manual (Inglese)
BlackandDecker Tagliabordi A Filo- Gl720 - Type 5 - Instruction Manual (Inglese)
BlackandDecker Tagliabordi A Filo- Gl720 - Type 5 - Instruction Manual (Inglese)
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
GL701<br />
GL710<br />
GL716<br />
GL720<br />
GL741
English (Original instructions) 4<br />
A<br />
B<br />
C<br />
2<br />
D
E<br />
F<br />
G<br />
H<br />
I<br />
J<br />
3
Intended use<br />
Your Black & Decker trimmer has been designed for trimming<br />
and finishing lawn edges and to cut grass in confined spaces.<br />
This appliance is intended for consumer use only.<br />
Safety instructions<br />
Warning! When using mains-powered appliances, basic<br />
safety precautions, including the following, should always be<br />
followed to reduce the risk of fire, electric shock, personal<br />
injury and material damage.<br />
u Read all of this manual carefully before operating the<br />
appliance.<br />
u The intended use is described in this manual. The use of<br />
any accessory or attachment or the performance of any<br />
operation with this appliance other than those recommended<br />
in this instruction manual may present a risk of personal<br />
injury.<br />
u Retain this manual for future reference.<br />
Using your appliance<br />
Always take care when using the appliance.<br />
u Always use safety glasses or goggles.<br />
u Never allow children or people unfamiliar with the<br />
instructions to use the appliance.<br />
u Do not allow children or animals to come near the work<br />
area or to touch the appliance or power supply cord.<br />
u Close supervision is necessary when the appliance is<br />
used near children.<br />
u This appliance is not intended for use by young or infirm<br />
persons without supervision.<br />
u This appliance is not to be used as a toy.<br />
u Only use the appliance in daylight or good artificial light.<br />
u Use in a dry location only. Do not allow the appliance to<br />
become wet.<br />
u Do not immerse the appliance in water.<br />
u Do not open the body casing. There are not userserviceable<br />
parts inside.<br />
u Do not operate the appliance in explosive atmospheres,<br />
such as in the presence of flammable liquids, gases or dust.<br />
u To reduce the risk of damage to plugs or cords, never pull<br />
the cable to remove the plug from a socket.<br />
Safety of others<br />
u This appliance is not intended for use by persons<br />
(including children) with reduced physical, sensory or<br />
mental capabilities, or lack of experience and knowledge,<br />
unless they have been given supervision or instruction<br />
concerning use of the appliance by a person responsible<br />
for their safety.<br />
u Children must be supervised to ensure that they do not<br />
play with the appliance.<br />
After use<br />
u When not in use, the appliance should be stored in a dry,<br />
well ventilated place out of reach of children.<br />
u Children should not have access to stored appliances.<br />
u When the appliance is stored or transported in a vehicle it<br />
should be placed in the boot or restrained to prevent<br />
movement following sudden changes in speed or direction.<br />
Inspection and repairs<br />
u Before use, check the appliance for damaged or defective<br />
parts. Check for breakage of parts and any other<br />
conditions that may affect its operation.<br />
u Do not use the appliance if any part is damaged or defective.<br />
u Have any damaged or defective parts repaired or replaced<br />
by an authorised repair agent.<br />
u Never attempt to remove or replace any parts other than<br />
those specified in this manual.<br />
Using an extension cable<br />
Always use an approved extension cable suitable for the<br />
power input of this appliance (see technical data). The extension<br />
cable must be suitable for outdoor use and marked accordingly.<br />
Up to 30 m of 1.5 mm 2 HO5VV-F extension cable can be used<br />
without loss of product performance. Before use, inspect the<br />
extension cable for signs of damage, wear and ageing.<br />
Replace the extension cable if damaged or defective.<br />
When using a cable reel, always unwind the cable completely.<br />
Additional safety instructions for grass trimmers<br />
Warning! Cutting elements continue to rotate after the motor<br />
is switched off.<br />
u Be familiar with the controls and the proper use of the<br />
appliance.<br />
u Before use, check the power supply cord and extension<br />
cord for signs of damage, ageing and wear. If a cord<br />
becomes damaged during use, disconnect the cord from<br />
the mains supply immediately. DO NOT TOUCH THE<br />
CORD BEFORE DISCONNECTING THE SUPPLY.<br />
u Do not use the appliance if the cords are damaged or worn.<br />
u Wear stout shoes or boots to protect your feet.<br />
u Wear long trousers to protect your legs.<br />
u Before using the appliance, check that your cutting path is<br />
free from sticks, stones, wire and any other obstacles.<br />
u Only use the appliance in the upright position, with the<br />
cutting line near the ground. Never switch the appliance<br />
on in any other position.<br />
u Move slowly when using the appliance. Be aware that<br />
freshly cut grass is damp and slippery.<br />
u Do not work on steep slopes. Work across the face of<br />
slopes, not up and down.<br />
u Never cross gravel paths or roads while the appliance is<br />
running.<br />
4
u Never touch the cutting line while the appliance is<br />
running.<br />
u Do not put the appliance down until the cutting line has<br />
come to a complete standstill.<br />
u Use only the appropriate type of cutting line.<br />
Never use metal cutting line or fishing line.<br />
u Be careful not to touch the line trimming blade.<br />
u Take care to keep the mains cable away from the cutting<br />
line. Always be aware of the position of the cable.<br />
u Keep hands and feet away from the cutting line at all<br />
times, especially when switching on the motor.<br />
u Before using the appliance and after any impact, check<br />
for signs of wear or damage and repair as necessary.<br />
u Never operate the appliance with damaged guards or<br />
without guards in place.<br />
u Take care against injury from any device fitted for<br />
trimming the filament line length. After extending new<br />
cutter line always return the machine to its normal<br />
operating position before switching on.<br />
u Always ensure that the ventilation slots are kept clear of<br />
debris.<br />
u Do not use the lawn trimmer (edge trimmer), if the cords<br />
are damaged or worn.<br />
u Keep extension cords away from cutting elements.<br />
Labels on appliance<br />
The following warning symbols are found on the appliance:<br />
+ Read the manual prior to operation.<br />
F<br />
8<br />
R<br />
Electrical safety<br />
#<br />
Wear safety glasses or goggles when operating this<br />
appliance.<br />
Keep people and animals at least 6 m away from<br />
the cutting area.<br />
Do not expose the appliance to rain or high<br />
humidity.<br />
This appliance is double insulated; therefore no earth<br />
wire is required. Always check that the power supply<br />
corresponds to the voltage on the rating plate.<br />
u If the supply cord is damaged, it must be replaced by the<br />
manufacturer or an authorised Black & Decker Service<br />
Centre in order to avoid a hazard.<br />
Features<br />
This appliance includes some or all of the following features.<br />
1. On/off switch<br />
2. Handle<br />
3. Cable restraint<br />
4. Power inlet<br />
5. Secondary handle<br />
6. Adjustment button<br />
7. Tube<br />
8. Guard<br />
9. Line trimming blade<br />
10. Spool housing<br />
11. Cutting line<br />
12. Edge guide<br />
Assembly<br />
Warning! Before assembly, make sure that the appliance is<br />
switched off and unplugged.<br />
Fitting the guard (fig. A)<br />
u Remove the hexagonal screws (13) from the head (14).<br />
u Place the guard (8) onto the appliance as shown.<br />
u Firmly press the guard until it snaps into place.<br />
u Secure the guard with the hexagonal screws.<br />
u Tighten the hexagonal screws using the hexagonal key<br />
(15) provided.<br />
Warning! Never use the appliance unless the guard is<br />
properly fitted.<br />
Releasing the cutting line<br />
In transit, the cutting line is taped to the spool housing.<br />
u Remove the tape holding the cutting line (11) to the spool<br />
housing (10).<br />
Connecting the appliance to the mains<br />
u Connect the female plug of a suitable extension cable to<br />
the power inlet (4).<br />
u Loop the cable through the cable restraint (3).<br />
u Insert the mains plug into a mains outlet.<br />
Warning! The extension cable must be suitable for outdoor use.<br />
Residual risks.<br />
Additional residual risks may arise when using the tool which<br />
may not be included in the enclosed safety warnings. These<br />
risks can arise from misuse, prolonged use etc.<br />
Even with the application of the relevant safety regulations<br />
and the implementation of safety devices, certain residual<br />
risks can not be avoided. These include:<br />
u Injuries caused by touching any rotating/moving<br />
parts.<br />
u Injuries caused when changing any parts, blades or<br />
accessories.<br />
5
u Injuries caused by prolonged use of a tool. When<br />
using any tool for prolonged periods ensure you take<br />
regular breaks.<br />
u Impairment of hearing.<br />
u Health hazards caused by breathing dust developed<br />
when using your tool (example:- working with wood,<br />
especially oak, beech and MDF.)<br />
Use<br />
Warning! Let the tool work at its own pace. Do not overload.<br />
Setting the appliance to trimming or edging mode<br />
(fig. B - D)<br />
The appliance can be used in trimming mode as shown in<br />
fig. B or in edging mode to trim overhanging grass along lawn<br />
edges and flower beds as shown in fig. C.<br />
Trimming mode (fig. B & D)<br />
For trimming, the trimmer head should be in the position<br />
shown in fig. B. If it is not:<br />
u Depress the adjustment button (6).<br />
u Rotate the tube (7), while releasing the button.<br />
u When the head is in position, the button will lock into place.<br />
Note: The tube will only rotate in one direction.<br />
Edging mode (fig. C & D)<br />
For edging, the trimmer head should be in the position shown<br />
in fig. C. If it is not:<br />
u Depress the adjustment button (6).<br />
u Rotate the tube (7), while releasing the button.<br />
u When the head is in position, the button will lock into place.<br />
Note: The tube will only rotate in one direction.<br />
Adjusting the height of the appliance (fig. D)<br />
This appliance has a telescopic mechanism, allowing you to<br />
set it to a comfortable height. There are three height settings.<br />
To adjust the height setting, proceed as follows:<br />
u Depress the adjustment button (6).<br />
u Gently pull the tube (7) out of the motor housing (16) to<br />
the desired height, while releasing the button.<br />
u When the tube is in position, the button will lock into place.<br />
Switching on and off<br />
u To switch the appliance on, squeeze the trigger lever (1).<br />
u To switch the appliance off, release the trigger lever.<br />
Warning! Never attempt to lock the trigger lever in the on<br />
position.<br />
Hints for optimum use<br />
General<br />
u In order to achieve optimum cutting results, only cut dry<br />
grass.<br />
6<br />
Trimming<br />
u Hold the appliance as shown in fig. B.<br />
u Gently swing the trimmer from side to side.<br />
u When cutting long grass, work in stages from the top.<br />
Take small cuts.<br />
u Keep the appliance away from hard objects and delicate<br />
plants.<br />
u If the appliance starts running slowly, reduce the load.<br />
Edging<br />
Optimum cutting results are achieved on edges deeper than<br />
50 mm.<br />
u Do not use the appliance to create edges.<br />
To create edges, use an edging spade.<br />
u Guide the appliance as shown in fig. C.<br />
u To make a closer cut, slightly tilt the appliance.<br />
Fitting a new spool of cutting line (fig. E & G)<br />
Replacement spools of cutting line are available from your<br />
Black & Decker dealer (cat. no. A6495).<br />
u Keep the tabs (17) depressed and remove the spool cover<br />
(18) from the housing (10).<br />
u Remove the empty spool (19) from the spool housing.<br />
u Remove any dirt and grass from the spool cover and<br />
housing.<br />
u Place the new spool onto the boss in the spool housing<br />
with the lines parked in the slots (23) (fig. F).<br />
u Insert the line ends through the appropriate eyelets (20) in<br />
the housing (10). Pull the slack line until it pulls out of the<br />
parked slots (23) (fig. G).<br />
u Align the tabs (17) on the spool cover with the cut outs (21)<br />
in the housing.<br />
u Push the cover (18) onto the housing (10) until it snaps<br />
securely into place.<br />
Note: Make sure that the cover is positioned, listen for two<br />
audible clicks to ensure both tabs (17) are correctly located.<br />
Warning! If the cutting lines protrude beyond the trimming<br />
blade (9), cut them off so that they just reach the blade.<br />
Winding new line onto an empty spool (fig. H - J)<br />
You may wind new cutting line onto an empty spool.<br />
Replacement packs of cutting line are available from your<br />
Black & Decker dealer (cat. no. A6171).<br />
u Remove the empty spool from the appliance as described<br />
above.<br />
u Remove any remaining cutting line from the spool.<br />
u First wind new line onto the uppermost part of the spool:<br />
- Feed 2 cm of cutting line into one of the slots in the<br />
upper section of the spool as shown.<br />
- Wind the cutting line onto the spool in the direction of<br />
the arrow. Make sure to wind the line on neatly and in<br />
layers. Do not criss-cross.
- When the wound cutting line reaches the recesses (22),<br />
cut the line.<br />
- Temporarily park the line in the slots (23) on one side of<br />
the spool as shown.<br />
u Repeat the above procedure for the second cutting line on<br />
the lower section of the spool. Park the line in the unused<br />
slots (23).<br />
u Proceed as described above to fit the spool on the<br />
appliance. Do not forget to release the cutting line from<br />
the parking slots (23).<br />
Warning! Only use the appropriate type of Black & Decker<br />
cutting line. Ensure that cutting line is present in both sections<br />
of the spool.<br />
Mains plug replacement (U.K. & Ireland only)<br />
If a new mains plug needs to be fitted:<br />
u Safely dispose of the old plug.<br />
u Connect the brown lead to the live terminal in the new plug.<br />
u Connect the blue lead to the neutral terminal.<br />
Warning! No connection is to be made to the earth terminal.<br />
Follow the fitting instructions supplied with good quality plugs.<br />
Recommended fuse: 5 A.<br />
Troubleshooting<br />
If your tool seems not to operate properly, follow the<br />
instructions below. If this does not solve the problem,<br />
please contact your local Black & Decker repair agent.<br />
Warning! Before proceeding, unplug the tool.<br />
Appliance runs slowly<br />
u Check that the spool housing can rotate freely.<br />
Carefully clean it if necessary.<br />
u Check that the cutting line does not protrude more than<br />
11 cm from the spool housing. If it does, cut it off so that it<br />
just reaches the line trimming blade.<br />
Automatic line feed does not work<br />
u Keep the tabs depressed and remove the spool cover<br />
from the housing.<br />
u Pull the cutting line until it protrudes 11 cm from the<br />
housing. If insufficient cutting line is left on the spool,<br />
install a new spool of cutting line as instructed above.<br />
u Align the tabs on the spool cover with the cut outs in the<br />
housing.<br />
u Push the cover onto the housing until it snaps securely<br />
into place.<br />
u If the cutting line protrudes beyond the trimming blade,<br />
cut it off so that it just reaches the blade.<br />
If the automatic line feed still does not work or the spool is<br />
jammed, try the following suggestions:<br />
u Carefully clean the spool cover and housing.<br />
u Remove the spool and check if the lever can move freely.<br />
u Remove the spool and unwind the cutting line, then wind it<br />
on neatly again as described above. Replace the spool as<br />
instructed.<br />
Maintenance<br />
Your Black & Decker corded/cordless appliance/tool has been<br />
designed to operate over a long period of time with a minimum<br />
of maintenance. Continuous satisfactory operation depends<br />
upon proper tool care and regular cleaning.<br />
Warning! Before performing any maintenance on corded/<br />
cordless power tools:<br />
u Switch off and unplug the appliance/tool.<br />
u Or switch off and remove the battery from the appliance/<br />
tool if the appliance/tool has a separate battery pack.<br />
u Or run the battery down completely if it is integral and then<br />
switch off.<br />
u Unplug the charger before cleaning it. Your charger does<br />
not require any maintenance apart from regular cleaning.<br />
u Regularly clean the ventilation slots in your appliance/tool/<br />
charger using a soft brush or dry cloth.<br />
u Regularly clean the motor housing using a damp cloth.<br />
Do not use any abrasive or solvent-based cleaner.<br />
u Regularly open the chuck and tap it to remove any dust<br />
from the interior (when fitted).<br />
Protecting the environment<br />
Z<br />
Separate collection. This product must not be<br />
disposed of with normal household waste.<br />
Should you find one day that your Black & Decker product<br />
needs replacement, or if it is of no further use to you, do not<br />
dispose of it with household waste. Make this product<br />
available for separate collection.<br />
z<br />
Separate collection of used products and packaging<br />
allows materials to be recycled and used again.<br />
Re-use of recycled materials helps prevent<br />
environmental pollution and reduces the demand for<br />
raw materials.<br />
Local regulations may provide for separate collection of<br />
electrical products from the household, at municipal waste<br />
sites or by the retailer when you purchase a new product.<br />
Black & Decker provides a facility for the collection and<br />
recycling of Black & Decker products once they have reached<br />
the end of their working life. To take advantage of this service<br />
please return your product to any authorised repair agent who<br />
will collect them on our behalf.<br />
7
You can check the location of your nearest authorised repair<br />
agent by contacting your local Black & Decker office at the<br />
address indicated in this manual. Alternatively, a list of<br />
authorised Black & Decker repair agents and full details of our<br />
after-sales service and contacts are available on the Internet<br />
at: www.2helpU.com<br />
Technical data<br />
GL701 GL710 GL716<br />
TYPE 3-5 TYPE 3-5 TYPE 3-5<br />
Input voltage V AC 230 230 230<br />
Power input W 550 520 580<br />
No-load speed min -1 6,500 6,500 6,500<br />
Weight kg 3.2 3.2 3.2<br />
GL720 GL741<br />
TYPE 3-5 TYPE 3-5<br />
Input voltage V AC 230 230<br />
Power input W 600 700<br />
No-load speed min -1 6,500 6,500<br />
Weight kg 3.2 3.2<br />
Hand/arm weighted vibration value according to EN 786:<br />
= 7.5 m/s 2 , Uncertainty = 1.5 m/s 2 )<br />
EC declaration of conformity<br />
MACHINERY DIRECTIVE<br />
OUTDOOR NOISE DIRECTIVE<br />
%<br />
GL701/GL710/GL716/GL720/GL741<br />
Black & Decker declares that these products described under<br />
"technical data" are in compliance with:<br />
98/37/EC (until Dec. 28, 2009), 2006/42/EC<br />
(from Dec. 29, 2009), EN 60335-1, EN 60335-2-91<br />
2000/14/EC, Lawn Trimmer, L ≤ 50 cm, Annex VIII<br />
KEMA Quality B.V., Utrechtseweg 310, 6802 ED Arnhem,<br />
The Netherlands<br />
Notified Body ID No.: 0344<br />
Level of accoustic power according to 2000/14/EC<br />
(Article 12, Annex III, L ≤ 50 cm):<br />
L WA (measure sound power) 95 dB(A)<br />
Uncertainty = 3 dB(A)<br />
L WA (guaranteed sound power) 96 dB(A)<br />
Uncertainty = 3 dB(A)<br />
These products also comply with directive 2004/108/EC.<br />
For more information, please contact Black & Decker at the<br />
following address or refer to the back of the manual.<br />
The undersigned is responsible for compilation of the technical<br />
file and makes this declaration on behalf of Black & Decker.<br />
_<br />
Kevin Hewitt<br />
Vice-President Global Engineering<br />
Black & Decker Europe, 210 Bath Road, Slough,<br />
Berkshire, SL1 3YD<br />
United Kingdom<br />
01-10-2009<br />
UK patent application no. 059745.6<br />
European Community design application nos.: 340385-0001 &<br />
339544-0001<br />
8
Guarantee<br />
Black & Decker is confident of the quality of its products and<br />
offers an outstanding guarantee. This guarantee statement is<br />
in addition to and in no way prejudices your statutory rights.<br />
The guarantee is valid within the territories of the Member<br />
States of the European Union and the European Free Trade<br />
Area.<br />
If a Black & Decker product becomes defective due to faulty<br />
materials, workmanship or lack of conformity, within 24 months<br />
from the date of purchase, Black & Decker guarantees to<br />
replace defective parts, repair products subjected to fair wear<br />
and tear or replace such products to ensure minimum<br />
inconvenience to the customer unless:<br />
u The product has been used for trade, professional or hire<br />
purposes;<br />
u The product has been subjected to misuse or neglect;<br />
u The product has sustained damage through foreign<br />
objects, substances or accidents;<br />
u Repairs have been attempted by persons other than<br />
authorised repair agents or Black & Decker service staff.<br />
To claim on the guarantee, you will need to submit proof of<br />
purchase to the seller or an authorised repair agent. You can<br />
check the location of your nearest authorised repair agent by<br />
contacting your local Black & Decker office at the address<br />
indicated in this manual. Alternatively, a list of authorised<br />
Black & Decker repair agents and full details of our after-sales<br />
service and contacts are available on the Internet at:<br />
www.2helpU.com<br />
Please visit our website www.blackanddecker.co.uk to<br />
register your new Black & Decker product and to be kept up to<br />
date on new products and special offers. Further information<br />
on the Black & Decker brand and our range of products is<br />
available at www.blackanddecker.co.uk<br />
9
10
ENGLISH<br />
Do not forget to register your product!<br />
www.blackanddecker.co.uk/productregistration<br />
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product<br />
code to Black & Decker in your country.
Australia<br />
Black & Decker (Australia) Pty. Ltd. Tel. 03-8720 5100<br />
20 Fletcher Road, Mooroolbark, Fax 03-9727 5940<br />
Victoria, 3138<br />
New Zealand<br />
Black & Decker Tel. +64 9 259 1133<br />
5 Te Apunga Place Fax +64 9 259 1122<br />
Mt Wellington<br />
Auckland 1060<br />
United Kingdom<br />
Black & Decker Tel. 01753 511234<br />
210 Bath Road Fax 01753 551155<br />
Slough, Berkshire SL1 3YD Helpline 01753 574277<br />
90552981 REV-0 10/2009