Makita SMERIGLIATR.ANGOLARE180mm - GA7020 - Manuale Istruzioni
Makita SMERIGLIATR.ANGOLARE180mm - GA7020 - Manuale Istruzioni
Makita SMERIGLIATR.ANGOLARE180mm - GA7020 - Manuale Istruzioni
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
ENGLISH (Original instructions)<br />
1. Shaft lock<br />
2. Switch trigger<br />
3. Lock lever<br />
4. Wheel guard<br />
5. Screw<br />
6. Bearing box<br />
7. Nut<br />
8. Lever<br />
9. Lock nut<br />
10. Depressed center wheel<br />
11. Super flange<br />
Explanation of general view<br />
12. Inner flange<br />
13. Lock nut wrench<br />
14. Abrasive disc<br />
15. Rubber pad<br />
16. Wire cup brush<br />
17. Wire wheel brush<br />
18. Abrasive cut-off wheel/diamond<br />
wheel<br />
19. Wheel guard for abrasive cut-off<br />
wheel/diamond wheel<br />
20. Outer flange 78<br />
21. Inner flange 78<br />
22. Exhaust vent<br />
23. Inhalation vent<br />
24. Commutator<br />
25. Insulating tip<br />
26. Carbon brush<br />
27. Brush holder cap<br />
28. Screwdriver<br />
SPECIFICATIONS<br />
Model <strong>GA7020</strong> <strong>GA7020</strong>S GA7021 GA9020 GA9020S<br />
Depressed center wheel diameter 180 mm 230 mm<br />
Max. wheel thickness<br />
6.5 mm<br />
Spindle thread<br />
M14 or 5/8” (country specific)<br />
Rated speed (n)/No load speed (n 0 ) 8,500 min -1 6,600 min -1<br />
Overall length<br />
473 mm<br />
Net weight 5.5 kg 5.7 kg 5.5 kg 5.8 kg 5.9 kg<br />
Safety class<br />
/II<br />
• Due to our continuing program of research and development, the specifications herein are subject to change without<br />
notice.<br />
• Specifications may differ from country to country.<br />
• Weight according to EPTA-Procedure 01/2003<br />
Intended use<br />
ENE048-1<br />
The tool is intended for grinding, sanding and cutting of<br />
metal and stone materials without the use of water.<br />
Power supply<br />
ENF002-2<br />
The tool should be connected only to a power supply of<br />
the same voltage as indicated on the nameplate, and can<br />
only be operated on single-phase AC supply. They are<br />
double-insulated and can, therefore, also be used from<br />
sockets without earth wire.<br />
For public low-voltage distribution systems of<br />
between 220 V and 250 V.<br />
ENF100-1<br />
Switching operations of electric apparatus cause voltage<br />
fluctuations. The operation of this device under<br />
unfavorable mains conditions can have adverse effects to<br />
the operation of other equipment. With a mains<br />
impedance equal or less than 0.27 Ohms it can be<br />
presumed that there will be no negative effects. The<br />
mains socket used for this device must be protected with<br />
a fuse or protective circuit breaker having slow tripping<br />
characteristics.<br />
General Power Tool Safety<br />
Warnings<br />
WARNING Read all safety warnings and all<br />
instructions. Failure to follow the warnings and<br />
instructions may result in electric shock, fire and/or<br />
serious injury.<br />
GEA010-1<br />
Save all warnings and<br />
instructions for future reference.<br />
GRINDER SAFETY WARNINGS<br />
GEB033-7<br />
Safety Warnings Common for Grinding, Sanding,<br />
Wire Brushing, or Abrasive Cutting-Off Operations:<br />
1. This power tool is intended to function as a<br />
grinder, sander, wire brush or cut-off tool. Read all<br />
safety warnings, instructions, illustrations and<br />
specifications provided with this power tool.<br />
Failure to follow all instructions listed below may result<br />
in electric shock, fire and/or serious injury.<br />
2. Operations such as polishing are not<br />
recommended to be performed with this power<br />
tool. Operations for which the power tool was not<br />
designed may create a hazard and cause personal<br />
injury.<br />
3. Do not use accessories which are not specifically<br />
designed and recommended by the tool<br />
manufacturer. Just because the accessory can be<br />
attached to your power tool, it does not assure safe<br />
operation.<br />
4. The rated speed of the accessory must be at least<br />
equal to the maximum speed marked on the power<br />
tool. Accessories running faster than their rated<br />
speed can break and fly apart.<br />
5. The outside diameter and the thickness of your<br />
accessory must be within the capacity rating of<br />
5