Water Dispenser Distributeur d'eau - Greenway Water Technology

Recommendations

Info

Draining the Reservoirs: IMPORTANT! Unplug the dispenser before performing this procedure. Dispense hot water until temperature drops to a safe level to avoid the risk of scalding. 1. Turn off the water supply, using manual shut-off valve at the rear of the dispenser. 2. Press both dispensing buttons until water stops flowing. 3. Place a container/bucket beneath the drain valve located at the rear of the dispenser (See Fig. 18). 4. Remove the drain cap and plug from the drain valve and let the remaining water flow into the container/bucket. Replace the cap and plug. Going Away on Vacation: When not using the dispenser for long periods of time or when going on vacation, unplug the dispenser and drain the reservoirs (see Draining the Reservoirs). Follow Initial Product Cleaning Procedures upon return and startup of the dispenser. specIfIcatIons: GWD9500W-POU / GWD9500BLS-POU Heating Temp (approx.): 194°F / 90°C Cooling Temp (approx.): 35 - 52°F / 2°C - 11°C Hot Cold Output per hr: 1.2 gal / 4.6 L 0.5 gal / 2.0 L Internal Tank: 0.2 gal / 0.6 L 0.8 gal / 3.6 L Power Consumption: 1150 W 88 W Working Water Pressure: Up to 120psi tr o u b l e s H o o t In G tIps: Attention: Do not return this product to the store. For questions on operation, assembly or parts, please contact us at www.greenwaywt.com or 1-866-253-0447. PROBLEM POSSIBLE CAUSE SUGGESTED SOLUTION Water dispenser is leaking. Check all water line connections for leaks. Filter not properly secured and locked. Drain cap and plug are not secure. Cold tank reservoir is overfilled. 10 Repair water line connections and make sure blue locking “c-clips” are installed on water lines. Secure Filter and lock. Ensure drain plug is secure and tighten drain cap. See RE-SETTING WATER OVERFLOW PROTECTION
No hot water. Insufficient water levels in the reservoir. The unit is unplugged. Kettle Feature button was not activated. Temperature limit switch tripped. No cold water. The circuit breaker in your home is tripped or the fuse is blown. Water dispenser is not dispensing water. Alarm is beeping continuously. The unit is unplugged. Thermostat needs to be adjusted colder. Make sure all water shut-off valves are open. Plug in the power cord. Activate the Kettle Feature button. The temperature limit switch will re-set automatically when the temperature of the water drops. Reset the breaker or replace the fuse. Plug in the power cord. Adjust thermostat between L (warm) and H (colder) levels to achieve desired temperature. Water shut-off valves are closed. Open all water shut-off valves. Water leakage detection system is activated. 11 Refer to Water Leakage Detection System instructions in the manual.
Page 1 and 2: Water Technologies Water Technologi
Page 3 and 4: YOUR GREENwAY ® wATER DISPENSER 1.
Page 5 and 6: Tools Required: • Plastic Pipe/Tu
Page 7 and 8: UNLOCKED LOCKED Fig. 10 Fig. 11 •
Page 9 and 10: 3. To access the reservoir system,
Page 11: Cleaning the Outside of the Water D
Page 15 and 16: Merci d'avoir acheté un distribute
Page 17 and 18: InstructIons d'InstallatIon: Il est
Page 19 and 20: Introduisez la conduite d'eau dans
Page 21 and 22: SYSTÈME DE DÉTECTION DE FUITES D'
Page 23 and 24: à gauche puis appuyez/maintenez en
Page 25 and 26: RÉENCLENCHEMENT DE LA PROTECTION C
Page 27 and 28: Garantie NE PAS RETOURNER CE SYSTÈ
Page 29 and 30: si no comprende, en su totalidad, l
Page 31 and 32: HERRAMIENTAS NECESARIAS: • Tuber
Page 33 and 34: BLOQUEADO DESBLOQUEADO Fig. 10 Fig.
Page 35 and 36: intentar cualquier operación de li
Page 37 and 38: lIMpIeZa y MantenIMIento Ver "Limpi
Page 39 and 40: suGerencIas para la solucIÓn de pr

Water Dispenser Distributeur d'eau - Greenway Water Technology

Create successful ePaper yourself

Delete template?

Save as template?