Roco 41260... 16stg.

More documents

Recommendations

Info

GB Starting locomotive operation GB Maintenance of the model Unwrap model: Take out loco cautiously using foil (fig. 1). Power car – assembly: see fig. 3. Operating instructions: Before use is advisable to let the loco go around about 30 minutes forwards and 30 minutes backwards without load, to obtain an optimal circuit and best tractive power. The smallest radius this model should run is R2 of the ROCO track system (R2 = 358 mm). Your locomotive will run smoothly on clean tracks only. For this purpose we recommend using item no. 46400, Roco track cleaning van, or item no. 10002, Roco track cleaning rubber, for removing heavy dirt. Fittings: In the enclosed accessory bag you will find small kits to be fitted on your locomotive. Please mount them cautiously. Attention! Use glue only if indicated (fig. 2). Running in digital mode: First remove the jumper from the interface and then put the plug of the chip into the interface (fig. 6). PLEASE NOTE! Double-heading during digital operation >> When double-heading two powered trains in a digitally operated system both power cars must be equipped with identical (same type and manufacturer) decoders! >> Both power cars must be coupled head to head i. e. facing each other! >> Both decoders must be programmed at the same time! To enjoy your locomotive for a long time, it ist necessary to service it regularly (i.e. after it has been in operation for approximately 30 hours). 1. Cleaning of wheel contacts: Wheel contacts easily get dirty on tracks which are not entirely clean. Use a small brush to remove dirt from spots marked in fig. 9. First remove gear cover (fig. 7). ➭ Assembly 2. Lubrication: Apply tiny oil drops to spots marked in fig. 8. Prior to lubrication dismantle locomotve / gear cover (fig. 4/7). We recommend using item no 10906, Roco oiler. For lubrication the gear-parts (e.g. cog-wheels, worm) we would recommend our Roco special grease (item No. 10905). Attention: Please do not oil these parts when using our grease. ➭ Assembly 3. Change of lights: First remove loco body (fig. 4) and then change lights (fig. 5). ➭ Assembly 4. Change of traction tyre: First remove gear cover (fig. 7). Take out the wheel set and remove traction tyre using a pin or a fine screwdriver. When pressing on the new traction tyre please avoid twisting it (fig. 10). ➭ Assembly 5. Carbon Brush Changing: First remove loco body (fig. 4), and then the motor (fig. 11). ➭ Assembly Assembly: During assembly please take care of correct position of contacts. Off you go! A.C. operation: see fig 12 + (I-XII). 4 13
Fig. 1 Fig. 2 Fig. 2 Fig. 3 Fig. 3 Motorwagen (mit Motor) Power car (with motor) Motrice (avec moteur) Abteilwagen Compartment coach Voiture à compartiments Abteilwagen Compartment coach Voiture à compartiments Speisewagen Dining car Voiture restaurant Küchenwagen Kitchen car Voiture cuisine Großraumwagen Open plan coach Voiture couloir central Motorwagen (ohne Motor) Dummy power car (no motor) Motrice (sans moteur) VT 11.5010 Vm11.516 Vm11.5117 Vm11.5302 VM11.5402 Vm11.5201 VT 11.5011 wahlweise optional à choisir Beleuchtungssätze: Lighting sets: Jeux d’éclairage: 101366 ➞ VT... (Motorwagen / Power car / Motrice) 40360 ➞ Vm... (Wagen / Coaches / Voitures) 8 9
Page 2 and 3: D Inbetriebnahme Ihrer Lokomotive D
Page 6 and 7: Fig. 4 1. 2. 2. Fig. 4 1. 1. VT...
Page 8: Fig. 10 Fig. 11 1. 1. 1. 3. 2. 3. 2

Roco 41260... 16stg.

Create successful ePaper yourself

Delete template?

Save as template?