You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
SCHERMATURA con copertura al 100%<br />
La schermatura è formata da:<br />
- nastro accoppiato di alluminio/poliestere 9/12<br />
micron<br />
- filo di drenaggio in rame stagnato<br />
- nastro poliestere da 12 micron applicato sul cavo<br />
secondo le norme CEI 46-5.<br />
La guaina esterna in PVC del tipo RZ di colore bianca,<br />
azzurra, rossa o grigia è flessibile e non propagante<br />
incendio secondo le norme CEI 20/22 II Edizione.<br />
CAVo <strong>ALLARME</strong> GR2<br />
Per le sue caratteristiche costruttive, a seguito di test<br />
superati positivamente, tale cavo è in “grado 2” con<br />
un isolamento di 250 V.<br />
CAVo <strong>ALLARME</strong> GR3<br />
Sezione/Size<br />
0,50 mmq n° 16 Ø 0,20 mm in rame rosso (red copper)<br />
0,75 mmq<br />
n° 24 Ø 0,20 mm in rame rosso (red copper)<br />
1,00 mmq<br />
n° 32 Ø 0,20 mm in rame rosso (red copper)<br />
1,50 mmq<br />
0,22 mmq<br />
GUAINA ESTERNA<br />
Per la sua costruzione particolare (con guaina esterna<br />
maggiorata), questo cavo è di “tipo grado 3” e quindi utilizzabile<br />
per un collocamento interno in canaline, anche<br />
in presenza di altri cavi, con un isolamento di 450 V.<br />
CAVo <strong>ALLARME</strong> GR4<br />
Caratteristiche tecniche • Technical characteristics<br />
Per la sua costruzione particolare (con doppia guaina esterna<br />
maggiorata), questo cavo è di “tipo grado 4” e quindi utilizzabile<br />
sia per un collocamento interno in canaline, anche<br />
in presenza di altri cavi, sia all’esterno essendo conforme alle<br />
norme CEI 64,8 IV edizione con un isolamento di 750 V.<br />
CoNDUTToRI<br />
I conduttori unipolari costituenti i fili di alimentazione (0,50-<br />
0,75-1,00 -1,50) sono isolati in PVC tipo R2 e superano la<br />
prova di tensione prevista dalle norme CEI 20-20 ossia: 5<br />
primi a 6000 Vcc a secco senza screpolature dell’isolante.<br />
I fili di segnalamento (0,22) sono isolati in PVC tipo R2 e<br />
superano la prova di tensione prevista dalle norme CEI<br />
20-20 ossia: 5 primi a 1000 Vcc a secco senza screpolature<br />
dell’isolante.<br />
Fili/Wires<br />
n° 48 Ø 0,20 mm in rame rosso (red copper)<br />
n° 07 Ø 0,20 mm in rame rosso (red copper)<br />
Diametro<br />
Diameter mm<br />
1,50<br />
1,80<br />
2,00<br />
2,40<br />
1,00<br />
Resistenza elettrrica<br />
MAX<br />
Electr. resist. Ohm/Km<br />
8/10 n° 1 Ø 8/10 mm in rame rosso (red copper) 1,40 42<br />
GuAiNA/SHEATH<br />
100% SHIELDING covering<br />
Shielding is made by:<br />
- coupled ribbon of aluminium / polyester 9/12 micron<br />
- drainage wire in tinned copper braid conductor<br />
- ribbon of polyester of 12 micron stuck on joined cable<br />
according to CEI 46-5 regulations.<br />
External jacket white, blue, red or grey is made by<br />
flexible PVC type RZ and not spreading fire according<br />
to CEI 20/22 - II Edition regulations.<br />
<strong>ALARM</strong> CABLE GR2 TYPE<br />
Owing to its making features, following to good results in<br />
tests, this cable is “GR2” with insulation of 250 V.<br />
<strong>ALARM</strong> CABLE GR3 TYPE<br />
EXTERNAL JACKET<br />
Owing to its particular making (with oversize external<br />
jacket), this cable is “Type GR3”, it can be put inside channels<br />
even with other cables with insulation of 450 V.<br />
<strong>ALARM</strong> CABLE GR4 TYPE<br />
Owing to its particular making (with double oversize<br />
external jacket), this cable is “Type GR4”, it can be<br />
put inside channels even with other cables and<br />
outdoor, according to CEI 64.8 regulations with an<br />
insulation of 750 V.<br />
UNIPOLAR WIRES<br />
Unipolar feeding wires (0,50-0,75-1,00-1,50) are insulated<br />
in PVC type R2. They pass the test of voltage according to<br />
CEI 20-20 regulations: 5 minutes with 6000 V. in dry direct<br />
current without any crack of insulation covering.<br />
Unipolar signal wires (0,22) are insulated in PVC type R2.<br />
They pass the test of voltage according to CEI 20-20 regulations:<br />
5 minutes with 1000 V. in dry direct current without<br />
any crack of insulation covering.<br />
sCherMO ALLuMiNiO/pOLiestere<br />
ALUMINIUM/POLYESTER SHIELD<br />
FiLO tAGLiAGuAiNA<br />
RIP CORD<br />
NAstrO pOLiestere<br />
RIBBON OF POLYESTER<br />
39<br />
26<br />
20<br />
14<br />
99<br />
FiLO dreNAGGiO<br />
iN rAMe stAGNAtO COrdAtO<br />
DRAINAGE WIRE<br />
IN TINNER COPPER-BRAID<br />
FiLi di<br />
seGNALe<br />
SIGNAL<br />
WIRES<br />
FiLi di<br />
ALiMeNtAziONe<br />
FEEDING WIRES